Glass casting displays great forming potential allowing for the realisation of three-dimensional glass elements of virtually any shape and size, as showcased in glass art. Disposable mould technology seems to be ideal for the fabrication of such customised and complex geometries, including for architectural and structural cast glass components deriving from structural topology optimization, since it offers great shape freedom and cost effectiveness. However, currently, glass casting on disposable moulds faces the major drawback of a resulting rough and opaque glass surface quality, requiring considerable post-processing to yield a glossy, smooth surface. This in turn results in a compromised dimensional accuracy and on increased time and production costs. If the surface remains unprocessed, it can greatly affect not only the visual but also the mechanical properties of the cast glass element. Aim of this research is to improve the surface quality of complex glass components cast in disposable moulds, directly during demoulding, reducing in this way the need for post-processing. To achieve this the research focuses on exploring ways to pre-process disposable moulds. In specific, the research focuses on series of kiln-cast laboratory experiments at various maximum firing temperatures / annealing schedules involving the use of two different types of disposable moulds, 3D-printed sand moulds and silica plaster moulds (Crystalcast®), and the application of refractory coatings, coating combinations and protective layers. The experimental work conducted thus far indicates that the best results are obtained at the lowest maximum temperature tested (870 °C), with the combination offering the best finishing quality to be a synthetic (ceramic) sand mould coated with Crystalcast® and Zirkofluid® (6672, 1219). Scaling-up of the kiln-cast prototypes unveils a complex correlation between the maximum dwell time at the maximum firing temperature and the casting effectivity/ performance of mould materials and coatings.@en

This paper introduces the use of structural topology optimization (TO) as a new design approach that enables the creation of monolithic load-bearing cast glass components of substantial dimensions with significantly reduced annealing times, rendering such components viable in terms of manufacturing. Using topology optimization, the glass mass can be optimized to match design loads whilst maintaining high stiffness and a homogeneous mass for even cooling. Initially, the two main TO approaches are discussed in terms of suitability for cast glass. A strain-based optimization is eventually preferred over Von Mises optimization in the specific study. To explore the potential of TO for optimizing structural cast glass components, three distinct studies are analyzed in ANSYS workbench: (i) a structural glass node, (ii) a cast glass floor and (iii) a pedestrian bridge. These lead to the establishment of a set of design/input criteria, taking into account glass as a material, casting as a manufacturing method, addressing also the safety of the structure. The design studies also reveal the inherent challenges of using TO for load-bearing glass components, which, in turn, lead to the establishment of design guidelines for developing a TO tool specifically for glass. Towards the real-life applicability of such complex-shaped, customized components, possible manufacturing methods are also discussed.@en

Among the environmental factors affecting glass weathering are humidity, exposure time, temperature, and the presence of pollutants in the atmosphere. Notwithstanding that the weathering produced depends on numerous factors, the important weathering effect of high humidity may be specifically mitigated by using a good chemical composition for the glass. To evaluate this relationship, flat glass samples from three suppliers were studied. The chemical composition of the samples was determined and the variability in compositions was evaluated to verify to what extent these small differences can affect their chemical durability. The chemical durability of the samples was evaluated by determining the hydrolytic resistance of crushed glass powder and using a visual appearance evaluation of bulk samples. The results demonstrate that when the samples are frequently washed, the compositional differences found between the suppliers can cause a significant difference in durability. The samples possessing the highest molar concentrations of Al2O3, and alkaline earth oxides (MgO + CaO) exhibited the highest hydrolytic resistance and the least visual deterioration. Differences encountered for the weathering products of glasses of comparable bulk compositions highlight that the process parameters play a major role in the alteration of the surface compositions of the glasses. For the unwashed samples, no consistent correlation was found between hydrolytic resistance and visual deterioration.@en

Up to now, fabricating cast glass components of substantial mass and/or thickness involves a lengthy and perplex annealing process. This has limited the use of this glass manufacturing method in the built environment to simple objects up to the size of regular building bricks, which can be annealed within a few hours. For the first time, structural topological optimization (TO) is investigated as an approach to design monolithic loadbearing cast-glass elements of substantial mass and dimensions, with significantly reduced annealing times. The research is two-fold. First, a numerical exploration is performed. The potential of reducing mass while maintaining satisfactory stiffness of a structural component is done through a case-study, in which a cast-glass grid shell node is designed and optimised. To achieve this, several design criteria in respect to glass as a material, casting as the manufacturing process and TO as a design method, are formulated and applied in the optimisation. It is concluded that a TO approach fully suited for three-dimensional glass design is as of yet not available. For this research, strain- or compliance based TO is selected for the optimization of the three-dimensional, cast glass grid shell node; in our case, we consider that a strain based TO allows for a better exploration of the thickness reduction, which, in turn, has a major influence on the annealing time of cast glass. In comparison, in a stress-based optimization, the considerably lower tensile strength of glass would become the main restrain, leaving underutilized the higher compressive strength. Furthermore, it is determined that a single, unchanging and dominant load-case is most suited for TO optimisation. Using ANSYS Workbench, mass reductions of up to 69% compared to an initial, unoptimized geometry are achieved, reducing annealing times by an estimated 90%. Following this, the feasibility of manufacturing the resulting complex-shaped glass components is investigated though physical prototypes. Two manufacturing techniques are explored: lost-wax casting using 3D-printed wax geometries, and kiln-casting using 3D-printed disposable sand moulds. Several glass prototypes were successfully cast and annealed. From this, several conclusions are drawn regarding the applicability and limitations of TO for cast glass components and the potential of alternative manufacturing methods for making such complex-shaped glass components.@en

An adhesively bonded, solid-glass brick pavilion has been designed by Konstantin Arkitekter as a landmark within the Aasivissuit – Nipisat UNESCO heritage in Greenland. The sculptural glass structure, measuring approximately 3.2 m in diameter × 2 m in height, faces a diverse set of engineering challenges compared to existing adhesively bonded glass brick structures. Placed in a remote location in the arctic circle, it has to withstand winter temperatures as low as -35 °C, and be built under a limited budget with the aid of the local population. Hence, key for the successful construction of the pavilion is finding an adhesive that satisfies the structural and aesthetic requirements of the project and simultaneously provides a simple and fast construction that spares the need for specialized building crew and sophisticated equipment, and is able to withstand the polar winter temperatures. Applicability and shear tests in (i) lab temperature conditions and (ii)) -5 °C lead to the final selection of: (a) 3M™ Scotch-Weld™ Polyurethane Adhesive DP610, which has a higher shear strength capacity, 1 mm gap filling capacity and is clear in colour, for bonding the bottom rows of the pavilion where higher strength is required due to the reduced overlapping of the bricks; and of (b) DOWSIL Experimental Fast Curing Adhesive developed by Dow Silicones Belgium particularly for this project, with a satisfactory shear strength, 3 mm gap filling capacity and white colour for the rest of the pavilion; its considerably larger gap filling capacity facilitates the ease of assembly as it can accommodate within the joint thickness the anticipated ± 1.5 mm standard size deviations of the soda-lime cast glass solid bricks and the possible accumulated deviations during construction. The paper further describes the application of the adhesive, first on a small-scale prototype, and then on site, and presents the encountered engineering and logistical challenges during the construction of the pavilion in Greenland.@en

The shaping freedom of cast glass in combination with the robustness of the resulting voluminous components opens up new, exciting directions in the field of structural glass. Yet, cast glass components remain brittle, limiting their structural applications in hyper-static compressive structures designed with conservative safety factors. Stretching these limits, this work investigates the reinforcement of cast glass by incorporating metal bars during the casting process, in a similar principle to reinforced concrete. Aim is to increase the ductility of the composite glass component, provide a warning mechanism prior to ultimate fracture and secure a postfailure load-bearing capacity. The development of hybrid glass components involves kiln-casting experiments using different metal-glass combinations, of similar thermal expansion coefficients. The method of introducing the metal bar in the glass during casting, and the effect of the selected forming temperature are investigated. The resulting metal-glass interfaces are examined for micro-cracks using a digital microscope, and for internal stresses using cross-polarized light. Two material combinations are found successful; soda lime silica with titanium and alkali borosilicate with Kovar. A hybrid borosilicate-Kovar 30*30*240mm beam is further tested in 4-point bending until failure, while its displacement is measured by Digital Image Correlation. The flexural response of the composite component is compared to the performance of unreinforced cast glass beams of similar composition. Although reinforced and unreinforced specimens show a comparable flexural strength, the reinforced specimen exhibits a warning mechanism well before failure, a gradual fracture and a post-failure load-bearing capacity. These attributes encourage the further exploration of cast glass reinforcement.@en

This paper presents the casting of volumetric glass components from glass waste as an alternative glass-recycling approach. The approach is characterized by its flexibility to accommodate a variety of compositions and ability to yield volumetric (solid or thick-walled) glass products that can tolerate higher contamination rates without a significant compromise to their properties. The novelty of the proposed glass-to-glass recycling method lies in the “as-received” recycling of glass waste, using relatively low forming temperatures (750–1200 °C). This reduces both the need for expensive, labour-intensive and logistically complex purifying, segregation and treatment (e.g. removal of coatings) techniques, and the required energy and CO₂ emissions for product forming. Aim of this paper is to provide an overview of the potential but also of the technical and supply-chain challenges and limitations that still need to be tackled, in order to introduce this recycling approach to the market. Addressing the supply-chain barriers of glass recycling, the principal challenges linked to the collection and separation of glass waste and the established quality standards for the prevailing glass production technologies are identified, in order to argue upon the potential of this new recycling approach. In continuation, addressing the technical challenges that are mainly linked to contamination, an overview is provided of the main experimental findings on the influence of cullet contaminants and casting parameters on the generation of defects, and how these affect the mechanical properties. The experiments study a broad variety of glass compositions, including soda-lime, borosilicate, aluminosilicate and lead/barium glasses, and different levels of cullet contamination, of embedded (e.g. frit, wire) or external (e.g. stones, glass ceramics) character. Based on the cullet characteristics and imposed firing schedules, different glass quality grades arise and critical defects are highlighted. Thereafter, the most promising glass waste sources that can be recycled via this novel recycling approach are distinguished and directions for future research are highlighted.

@en

Cast glass is a promising, three-dimensional expression of the material for architectural and structural applications, particularly for the creation of all-transparent, self-supporting structures and envelopes. Typically applied in the form of solid blocks, cast glass components can be used as repetitive units to comprise fully-transparent, cast glass masonry walls. To maximize transparency and ensure an even load distribution, the glass blocks are bonded together by a colourless adhesive. Currently, there is a lack of standardized structural specifications, strength data and building guidelines for such adhesively-bonded cast glass-block systems. As a result, any new application is accompanied by experimental testing to select the adhesive and certify the adhesively bonded system. Since the choice of adhesive is highly dependent on the prerequisites set for each case-study -such as the structural and visual performance, available budget, the structure’s geometry and climate conditions- the preselection of the most prominent adhesive family at an early project stage can prevent an excessive budget and construction complications. This paper, therefore, aims to shed light on the selection process of adhesives for cast glass assemblies by first providing an overview of the most suitable bonding media families for such systems; these include stiff adhesives, flexible adhesives and cement-based mortars. Following, the paper reviews the research & development process of the adhesively-bonded glass-block systems in three distinct built projects, in which the TU Delft team has been involved: The Crystal Houses façade (NL), the LightVault, a robotically assembled glass vault (UK) and the Qaammat pavilion in the arctic circle (GL). The adhesive requirements for each of the three case studies are discussed in terms of structural and visual performance and ease-of-assembly (constructability). These criteria are decisive in pointing out the most promising bonding media family per case-study. The final shortlist of adhesive candidates within that bonding media family is subject to the full list of performance criteria, but also to market availability. The shortlist of adhesive candidates are typically experimentally evaluated, first via application testing and then via strength tests in order to choose the most suitable candidate. Based on the above, the review concludes in proposing guidelines for the effective selection, design and experimental verification of adhesively-bonded cast glass assemblies.@en

Cast glass has great application potential in the architectural realm, yet, despite its possibilities and attractiveness, designers, engineers and developers are, from an early design stage, hesitant to employ it; the limited available and craft-based manufacturing facilities, the questionable quality of the product, the missing engineering data and quality control processes and the uncertainties linked with the structural application of cast glass, lead to discouraging high cost/ high risk solutions. Within the listed challenges and uncertainties, perhaps the most striking is our inability to answer the most obvious question: what is the strength of cast glass? A simple answer to this question does not exist, as the mechanical properties of cast glass vary from product to product, and are directly influenced by the employed chemical composition, thermal history, and casting process. Adding to this complexity, further questions over the mechanical properties and quality arise, once waste (contaminated) glass cullet and lower processing temperatures are used, in the efforts of reducing the environmental impact of cast glass components. Focusing on this knowledge gap, the aim of this work is to develop an understanding of the effect of the casting parameters on the meso-level structure of cast glass, and thereupon of the relationship between this meso-level structure and the strength, stiffness and fracture resistance of cast glass components. Towards this aim, the dissertation adopts an experimental approach based on physical prototyping by kiln-casting, and destructive and non-destructive testing. The experimental work shows that by kiln-casting, a larger variety of chemical compositions can be cast, even at relatively low processing temperatures. As a consequence, a broad range of mechanical properties arises, especially when waste cullet is employed. Based on the casting parameters, combinations of different defects, grouped in meso-level structures, are commonly found in cast glass, yet these can often be tolerable when situated in the glass bulk. The dissertation highlights the potential of recycling-by-casting of currently challenging to recycle glass waste into reliable and aesthetically unique structural components, and the advantages of engineering composite cast glasses. It also underlines the need for manufacturing guidelines, test data, product certifications and quality control protocols, for the successful implementation of cast glass in the built environment. @en

Beginning of November 2020, five years after realizing the famous Crystal House concept with architectural firm MVRDV, the Glass Research Group of the Faculty of Architecture and the Built Environment of the Technical University of Delft was contacted by architect Konstantin Ikonomidis with the request to provide glass expertise for a small - yet challenging - project.@en

This paper explores a novel restoration approach for consolidating historic structures using structural glass to substitute for the missing elements, preserving at the same time the structural integrity of the structure. A restoration design is proposed for the hypothetical consolidation of the remaining tower of Schaesberg Castle, in Limburg, The Netherlands. The masonry walls suffer from a significant loss of material and a temporary steel structure currently prevents the tower from collapsing. It is proposed to use stacked float glass to fill the missing parts of the wall. The connection between the old masonry and new glass is the most challenging aspect given the different physical and mechanical properties of the materials, which need to work together in a coherent way. Shear tests of various connecting materials are carried out in order to evaluate the performance of this connection with respect to aspects of compatibility and feasibility.@en

The emerging interest in the architectural applications of cast glass components reveals a knowledge gap on the mechanical properties of cast glass. Apart from its chemical composition, cast glass is characterized by its manufacturing history and thermal profile, often inheriting a set of defects that define its properties. The role that inhomogeneities in the bulk of voluminous glass components have on the strength of the final product is also uncertain. Systematic testing is therefore necessary for the safe structural application of cast glass. Towards this direction, the presented research aims to experimentally investigate the fracture resistance of cast glass under sharp contact loading, by means of a customized splitting test using a sharp linear indenter. Cubic specimens with 50 mm sides are kiln-cast at low forming temperatures, employing a variety of silicate-based cullet and firing schedules and their inherent defects are documented. The results of the splitting tests show that the borosilicate specimens fail at the highest splitting force, followed by the soda lime float specimens, while the fused or porous specimens have a significantly lower resistance to fracture. The strength order of the various glasses, as this results from the splitting tests- is opposite to that found earlier in four-point bending tests, due to the different fracture mechanisms activated. The fracture resistance of a glass specimen is governed, first by its ability to deform around the indenter to relief the developing stresses and then by its bond strength to resist crack propagation. Thus, a good balance between glass network flexibility and high bond dissociation energy is required, explaining why the tested homogeneous borosilicate and soda lime glasses are more resistant than the modified soda lime compositions with high alkali content. In addition, the fractographic analysis indicates that the non-stress inducing flaws in the bulk have a negligible contribution to the fracture resistance of the specimens.@en

Cast glass has great potential for diverse load-bearing, architectural applications; through casting, volumetric glass components can be made that take full advantage of glass’s stated compressive strength. However, the lack of engineering, production and quality control standards for cast glass and the intertwined ambiguities over its mechanical properties-particularly due to the variety in chemical compositions and the lack of understanding of the influence of flaws occurring in the glass bulk-act as an impediment to its wide-spread application. Addressing the above uncertainties, this work studies a total of 64 silicate-based glass specimens, prepared in 20 * 30 * 350 mm beam size, either by kiln-casting at relatively low forming temperatures (970–1120 ∘C), or by modification of industrially produced glass. For the kiln-casting of the specimens, pure and contaminated recycled cullet are used, either individually or in combination (composite glasses). The defects introduced in the glass specimens during the casting process are identified with digital microscopy and qualitative stress analysis using cross polarized light, and are categorized as stress-inducing, strength-reducing or harmless. The Impulse Excitation Technique is employed to measure the Young’s modulus and internal friction of the different glasses. Differential Scanning Calorimetry is used on a selection of glasses, to investigate changes in the glass transition range and fictive temperature of the kiln-cast glasses due to the slower cooling and prolonged annealing. The four-point bending experiments are shedding light upon the flexural strength and stiffness of the different glasses, while the fractographic analysis pinpoints the most critical defects per glass category. The experiments show the flexural strength of cast glass ranging between 30–73 MPa, according to the level of contamination and the chemical composition. The measured E moduli by both methods are in close agreement, ranging between 60–79 GPa. The comparison of the flexural strength with prior testing of cast glass involving shorter span fixtures showed a decreasing strength with increasing size for the contaminated specimens, but similar strengths for pure compositions. The results highlight the versatile role of defects in determining the glass strength and the complexity that arises in creating statistical prediction models and performing quality control.@en

Connecting glass with heat bonds is a way to create all-transparent glass structures. Two methods have been researched in theory and practice, glass welding, through local heating, and glass fusion through global heating. Both methods have been applied to produce 10 mm thick T-sections of soda lime glass while preventing thermal shock failure and minimizing residual stress. These specimen, and specimen with an adhesive joint, have been tested destructively. It is concluded that it is possible to connect 10 mm thick soda lime glass by welding, if the glass is preheated and the surrounding temperature remains elevated during the welding process. Additionally, glass fusion of a similar product through global heating is possible for the applied temperature schedule. The mould has a paramount influence on the quality of the product. For both production methods, the annealing schedule was adequate to reduce residual stress. The average strength of the fused specimen was 44% larger. The standard deviation of the welded specimen was smaller: the standard deviation relative to the mean value was 9% for the welded specimen and 60% for the fused specimen. However, the amount of tested specimen is little. This research is a proof of concept for heat bonding soda lime glass of a structurally relevant thickness. @en

It is not obvious to talk about glass recycling when we realize that a mature recycling procedure for glass bottles is already working well. However, apart from glass bottles, unfortunately, that a large amount of glass will disappear into landfills. This large quantity of unrecycled glass indicates that there is a large potential in upgrading the glass recycling process. In the field of architecture, we see a fast-growing interest in using glass, also for structures. The glass bricks of Crystal Houses in Amsterdam are a good illustration. Aiming at maximizing the recyclability of glass, this paper focuses on the structural use of the glass components made from recycled glass through kiln casting method. An overview of the existing glass recycling industry is given at the beginning, followed by a discussion of glass type to be recycled. After this the experimental process of the glass recycling is introduced, which uses coated float glass with tints as the basic material to be recycled. Following this, a further exploration in three structural properties of the recycled products is conducted, namely: Young’s modulus, coefficient of thermal expansion and the fracture strength, with mechanical experiments. Finally, the test results are analyzed together with the chemical composition of the recycled products, which is derived from X-ray fluorescence (XRF) analysis. The result contains the value of mechanical properties and it evaluates the possibility of the structural use as a recycled-float-glass beam. In the end of this paper, the future possibility and feasibility in structural application of recycling waste float glass are discussed.@en

The problem of sustainability represents one of the most important issues that the world has to face nowadays, not only in terms of energy consumption and of the consequent CO2 emissions, but also in terms of material waste streams that end in landfill. 38 million tons of glass waste are produced every year in the European Union and new targets have been set for 2020 towards a more sustainable management of such wastes. Nowadays, only the container glass industry has reached a considerable recycling rate, while for all the other sectors we are still witnessing downgrading processes. Looking at the world of construction, glass has been more and more employed as a structural material thanks to its high transparency and compression strength. Although the use of glass can be attractive under multiple aspects and its production is continuously increasing, once employed as a construction element, it is rarely reused or recycled due to the high-quality requirement demanded to the industry of production. Nevertheless, besides its main applications as a 2-dimensional element, the new technology of cast glass has been recognised as a potential mean of glass recycling. Here, glass is designed and used under the form of repetitive 3-dimensional units assembled in a whole geometrical shape. In fact, thanks to its higher load-bearing capacity under monolithic shapes, this glass can admit less restrictions and potentially incorporate different types of waste. For this reason, the aim of this experimental work is to find a possible combination between glass families, specifically soda-lime, borosilicate and lead-crystal glass, to be recycled as cast glass components. Each type of glass was powdered or grinded under the form of cullet and different mixtures were prepared to be melted at temperatures of 970°C, 1120°C and 1200°C through the kiln-cast tecnique. Finally, an experimental splitting test was performed to define a force trend and a fracture behaviour for each sample. Some preliminary results have been achieved drawing the guidelines for a further investigation. Soda-lime-silica glass and lead-crystal glass mixture revealed to be the most compliant glass recipe with the required physical and mechanical properties, when reheated at 1120°C. The decrease in the melting temperature of the compound and the higher transparency given by the addition of lead glass revealed the potential benefit, in terms of sustainability, for future projects.@en

This paper explores two alternative mould fabrication technologies that allow for the casting of (solid) glass components with a great degree of freedom in shape and size and/or of a customized design, in a cost-efficient way. In specific, the paper discusses the research, design and experimental work conducted at TU Delft on 3D-printed sand moulds and adjustable, high-precision steel moulds. 3D-printed sand moulds can provide a high-accuracy, cost-effective solution for solid glass components of complex geometry and/or of customized design. Although this mould technique is already used for metal castings, it remains still unexplored in the field of glass casting. Accordingly, this paper presents the first experimental findings at TU Delft of this mould technology: mould samples using different binders and treated with various coatings for surface finishing are tested in the high temperatures anticipated in glass (kiln-)casting. Following, 3D-printed moulds are prepared for a given glass geometry and physical glass prototypes are made by kiln-casting. Adjustable metal moulds are another mould technique that offers a degree of freedom in the modulus of a structure. Essentially, components of different sizes and, to an extent, shapes can be generated by the same mould. Accordingly, the design principles and engineering of such a mould and the potential applications and limitations of this technology are discussed. As a proof of concept, an adjustable mould is made using 3D-printed PLA and laser-cut MDF. The mould is used for the generation of wax models of variable forms, which are used to kiln-cast glass prototypes by the lost-wax technique. Based on the findings on both presented mould technologies, guidelines are given on their suitability according to the production volume, the level of accuracy required and the complexity and variation of forms involved. @en

Currently, tons of high quality commercial glass are down-cycled or landfilled due to contaminants that prevent close-loop recycling. Yet, this glass is potentially a valuable resource for casting robust and aesthetically unique building components. Exploring the potential of this idea, different types of non-recyclable silicate glasses are kiln-cast into 30 × 30 × 240 mm beams, at relatively low temperatures (820–1120∘C). The defects occurring in the glass specimens due to cullet contamination and the high viscosity of the glass melt, are documented and correlated to the casting parameters. Then, the kiln-cast specimens and industrially manufactured reference beams are tested in four-point bending, obtaining a flexural strength range of 9–72 MPa. The results are analysed according to the role of the chemical composition, level of contamination and followed casting parameters, in determining the flexural strength, the Young’s modulus and the prevailing strength-limiting flaw. Chemical compositions of favourable performance are highlighted, so as critical flaws responsible for a dramatic decrease in strength, up to 75%. The defects situated in the glass bulk, however, are tolerated by the glass network and have minor impact on flexural strength and Young’s modulus. The prerequisites for good quality recycled cast glass building components are identified and an outline for future research is provided.@en

The success of projects such as the Crystal Houses façade in Amsterdam has triggered an increasing interest from architects, engineers and glass producers in the development and application of structural cast glass components. This interest raises, simultaneously, the needs for a controlled manufacturing process, a system for quality control and structural validation, to guarantee the production of safe components. Manufacturing-related flaws, such as stones, cord inclusions, or air-bubbles, occurring in the mesostructure of the components, form weak zones within the material and may lead to “spontaneous” cracking. The casting parameters such as the forming temperature and corresponding glass viscosity, the dwell time at this temperature and the cooling rate, largely determine the homogeneity of the final product. Additional complexity arises once the use of waste/recycled glass is considered, due to the probable presence of variable glass compositions and miscellaneous contaminants in the initial batch. The risk of inhomogeneity and resulting eventual mechanical failure, indicates the necessity of understanding the causes of flaw-formation and the impact of the developed flaws on the structural performance of the cast components. Therefore, a series of 50mm cubic glass components are cast at the TU Delft Glass Lab, using a selection of already formulated discarded soda-lime glasses from different commercial applications. The cubes’ meso-structure is documented and- when required- scanned employing a Computer Tomography scanner and a polariscope to identify possible density differentials and internal stresses respectively. Then the cubes are tested for splitting strength and their performance is analyzed in relation to the previously documented flaws. The destructive tests suggest that there is a correlation between the meso-structure, structural performance and failure pattern of the cast glass components.@en