Developed by Delft University of Technology, the tri-component polyurethane modified cold binder (PMCB) displays impressive durability and strength in asphalt mixtures, showing promise as a reliable binder for cold in-place recycling. However, when applying PMCB for rapid, in-situ recycling, the presence of moisture in reclaimed asphalt pavement (RAP) poses a significant challenge. To address this, an innovative approach involving treatment of the wet RAP with Calcium dioxide (CaO) prior to the integration of PMCB was tested. Evaluation methods used included the Indirect Tensile Test (ITT), followed by the calculation of the Indirect Tensile Strength Ratio (ITSR) to assess moisture susceptibility. Furthermore, Cantabro tests were performed to determine the material loss under abrasion and weathering conditions. These assessments underscored the feasibility of this approach. The treatment of wet RAP with CaO has proven a viable strategy for rapid in-situ recycling with PMCB, contributing to sustainable pavement construction. In addition, the research identified that a 5.5% concentration of the PMCB binder maximizes structural integrity and performance in the considered RAP.

@en

The film thickness of asphalt mixtures is critical for determining their performance and aging durability. However, understanding of the appropriate film thickness and its influence on performance and aging behavior for high-content polymer-modified asphalt (HCPMA) mixtures is still limited. This research aims to examine the relationship between film thickness, performance, and aging behavior of HCPMA mixtures in order to establish an optimal film thickness that ensures satisfactory performance and aging durability. HCPMA specimens with film thicknesses ranging from 6.9 μm to 17 μm were prepared using a 7.5% SBS-content-modified bitumen. Various tests, including Cantabro, SCB, SCB fatigue, and Hamburg wheel-tracking tests, were conducted to evaluate raveling, cracking, fatigue, and rutting resistance before and after aging. The key findings indicate that insufficient film thickness negatively affects aggregate bonding and performance, while excessive thickness reduces mixture stiffness and resistance to cracking and fatigue. A parabolic relationship between the aging index and film thickness was observed, suggesting that increasing film thickness improves aging durability up to a point, beyond which excessive thickness adversely impacts aging durability. The optimal film thickness for HCPMA mixtures, considering performance before and after aging and aging durability, falls within the 12.9 to 14.9 µm range. This range ensures the best balance between performance and aging durability, offering valuable insights for the pavement industry in designing and utilizing HCPMA mixtures.@en

High-Content SBS Polymer Modified Asphalt Mixtures (HCPMA) combined with fibers have gained popularity in porous pavement construction due to their superior performance. Although the aging behavior of HCPMA has been extensively studied, the impact of fibers on performance and aging susceptibility remains unclear. This research investigates the influence of two representative fibers (lignin and polyester) on the raveling, cracking, fatigue, and rutting resistance of HCPMA before and after aging using Cantabro loss tests, SCB strength tests, SCB fatigue tests, and Hamburg Wheel-Tracking tests. The results indicate that in the original state, polyester fiber slightly enhances HCPMA performance, while lignin fiber shows limited or even adverse effects on cracking, raveling, fatigue, and rutting resistance. However, both fibers exhibit a more pronounced enhancement effect after short- and long-term aging. FTIR analysis reveals that fiber addition does not significantly impact bitumen oxidation and polymer degradation. The excellent properties of High-Content SBS Polymer Modified Bitumen (HCPMB) in the original state create a "masking" effect that conceals the enhancement effect of fibers, which becomes more evident after
long-term aging. Consequently, it is recommended that the performance evaluation and design of open-graded asphalt mixtures containing HCPMB be based on post-aging performance. @en

This research aimed to investigate the attenuation mode of the layer modulus of asphalt pavement in accelerated pavement testing (APT). A full-scale experimental section was constructed and tested using the APT facility. Two non-destructive testing (NDT) methods, named falling weight deflectometer (FWD) technique and portable seismic property analyzer (PSPA) test, were used to obtain the layer moduli of asphalt pavement during the APT test. The variation patterns of layer moduli obtained by FWD and PSPA tests were calculated and compared after the temperature was corrected to 20 ℃. It was found that the variation pattern of surface layer modulus based on field FWD measurements was consistent with the one measured from PSPA tests. That is the modulus of the surface layer increases with the APT load repetitions firstly and then decreases with the rise of the repetitions. The modulus values of the surface layer measured from PSPA tests are obviously larger than those backcalculated based on deflection basins. The ratio of the measured surface layer modulus based on the PSPA test to the backcalculated one based on the FWD test ranges between 2.06 and 2.71. The backcalculated base layer modulus always declines with the increasing loading repetitions. The attenuation patterns of the surface layer modulus and the base layer modulus in the damage stage are described as E_a=421100*N^-0.6119 and E_b=128000*N^-0.1096, respectively.

@en

In a mechanistic-empirical (ME) pavement design method, the modulus of asphalt concrete (AC) is essential. The in-situ AC modulus can be obtained by the surface wave method (SWM). However, the measured modulus needs to be adjusted to the design frequency values. This study aimed to propose a frequency adjustment method for the in-situ AC seismic modulus. For this purpose, coring and dynamic modulus tests, FWD (Falling Weight Deflectometer) tests, and PSPA (Portable Seismic Pavement Analyzer) tests were carried out in the accelerated pavement test (APT). The master curves generated by the dynamic modulus results correlated well with the moduli determined from the other tests. Based on this relationship, a frequency adjustment factor was developed for the seismic modulus of the undamaged AC layer. For the damaged AC layer, the proposed factor was modified by incorporating the effect of the damage. Finally, to validate the frequency adjustment factor, the measured maximum tensile strains in the APT were compared with the values determined from the adjusted seismic moduli. The results prove that the frequency adjustment factor is appropriate to obtain the design modulus from the surface wave test. The PSPA test is also recommended to obtain the in-situ AC seismic modulus.

@en

The modulus back-calculation of asphalt pavement layers using falling weight deflectometer (FWD) data has become one of the most important methods of evaluating pavement bearing capacity. Several back-calculation methods have been proposed to estimate material properties. A new modulus back-calculation method called the deflection basin regulation algorithm (DBRA) has emerged recently. This algorithm requires an inertial point and two characteristic points in a deflection basin for back-calculating the moduli of three-layer pavement. However, the existing characteristic point positions are determined based on the theoretically calculated deflections and have not been verified by measured deflections. In this research, the field-measured deflection basins of different pavement structures are used to determine the optimal characteristic point positions to improve the new back-calculation method. First, the optimal point positions are determined based on the effects of the positions on the back-calculation variability. Then the back-calculated results based on the optimal characteristic points are compared to the results obtained using the MODULUS program. Finally, the improved modulus back-calculation method is also verified by the deflections from two pavement structures at different temperatures and loading levels. It was found that the optimal characteristic point positions were located at distances of 0 and 60 cm from the load center. Both comparative analysis and independent verification prove that the determined optimal characteristic point positions work well for back-calculating the layer moduli of other pavement structures. The findings of this research may facilitate the application of the DBRA for modulus back-calculation.

@en

Asphalt concrete (AC) modulus reduction caused by repeated axle loading significantly affects pavement long-term performance; including when built on a semi-rigid layer. However, quantifying this effect is challenging. The primary objective of this paper was to monitor and evaluate modulus reduction and fatigue damage accumulation at various AC depths utilizing data obtained from two semi-rigid pavement sections. During loading, a non-destructive method, portable seismic pavement analyzer (PSPA), was used to predict the modulus ratio. PSPA test results show that the damage is nonlinear with respect to the loading passes. Also, depth and AC thickness can influence the development of damage. A developed model showed that it could predict the aforementioned nonlinear relationship. The model parameters can be used to identify the damage level at various AC depths. Unexpected compared with previous understanding, the damage in AC layers was found to increased first, then decreased, and finally increased with the depth. Since PSPA is cheap, portable, and easy to apply, this method to identify the damage level in AC layers is proven to be applicable and practical.

@en

Asphalt pavement is a multi-layer continuous structure with an interlayer bonding condition that can greatly influence its bearing capacity and must be monitored over the whole service length. Hence, proper maintenance and rehabilitation measures are taken and better feedback can be made for the design. Nevertheless, asphalt pavement interlayer bonding condition plays a hidden role and is difficult to quantify unless applying damage discovery techniques like drilling core process. The original structure is destroyed by the damage detection approaches, the results also suffer from low coverage rate and high dispersion, therefore, actual engineering demands are not satisfied. Here, some recent methods are briefly presented based on asphalt pavement interlayer bonding condition non-destructive diagnosis and their restrictions are discussed. Moreover, a new technique is provided with the merits of utilizing only mechanical simulation and overall superficial distresses condition evaluation index with high accuracy. This simulation procedure adopts bridging principles to build a connection between asphalt pavement superficial distresses and asphalt pavement micro mechanic parameters. It uses a structure behavior equation capable of identifying four typical deterioration modes and has specific physical meaning parameters to predict asphalt pavement overall superficial distresses. The established model allows the asphalt pavement interlayer bonding acting as a hypothetical input variable. The known input variables include easily obtainable design parameters of the asphalt pavement structure, historical superficial distresses, surface deflection, traffic load, and environmental factors, however, the output is the predicted asphalt pavement overall superficial distresses condition. The asphalt pavement interlayer bonding condition is defined by contrasting the theoretical asphalt pavement overall superficial distresses conditions between its complete bonding condition and discontinuous bonding condition to a certain degree. Examples in parts of the Jingha highway show that great discrepancies exist between theoretical asphalt pavement overall superficial distress in the condition of complete interlayer bonding and actual asphalt pavement overall superficial distress. The actual asphalt pavement sections in overall superficial conditions are deteriorated much faster than normal ones. By setting the asphalt pavement interlayer bonding continuations as 75% and 90% for K315-K316 section and K316-K317 section, respectively, the revised and predicted overall superficial distresses of the theoretical asphalt pavement are consistent with the real ones. The hypothetical values are then chosen as the diagnosed quantitative asphalt pavement interlayer bonding continuations and are proven to be correct through drilling core sample results. The analyses in other sections show that middle traffic volume asphalt pavement structure is quite weak when its interlayer bonding continuation is 70%, and under this value, its bearing capacity is almost equivalent to the situation when its interlayer bonding continuation is 0%; when its interlayer bonding continuation is 85% or more, its bearing capacity is almost equivalent to the situation where its interlayer bonding continuation is 100%. This proposed non-destructive diagnosis method for asphalt pavement interlayer bonding condition is effective and shows good application prospects in road engineering.

@en

The modulus of asphalt mixture is traditionally measured from the laboratory dynamic modulus test. However, different laboratory test methods often lead to obviously different test results. To evaluate the moduli of asphalt mixtures as constructed in field pavements, this study back-calculated the moduli of the pavement layers, based on measured strain data in Accelerated Pavement Testing (APT). Field tests were conducted to measure strains at different locations of the built pavement section at different temperatures and wheel motion speed. The loading frequencies of the asphalt layer subject to different motion speeds were calculated based on the duration of measured strain pulses. Subsequently, the relationship between the motion speed and the loading frequency was established. An finite element (FE) model of the pavement section was created, which was used to back-calculate the moduli of asphalt pavement layers using the measured strain data. Based on the back-calculation results at different loading conditions, the master curve of the field asphalt layer was determined. This master curve was further used to compare with that obtained from laboratory uniaxial compressive test. The relationship between the field and laboratory moduli was determined to be E_Laboratory= 1.298E_Field.

@en

The asphalt-based pavement performance evaluation includes the derivation of the dynamic moduli and loading frequencies of pavement layers under various traffic- and climatic-induced loading conditions. The traffic-induced strain pulses and loading frequencies of commonly used (semi-rigid, flexible, and steel deck) asphalt pavements were experimentally determined by vehicular loading field tests with embedded strain gauges for different axle loads, motion speeds, and temperatures. It was found that the axle load values had no noticeable effect on the pavement loading frequency, which was mainly controlled by the vehicular motion speed. The transverse frequencies were found to be higher than longitudinal ones, while the distributions of loading frequencies by pavement depth differed for three pavements under study. The frequency values at temperatures over 35 °C exceeded those at lower temperatures, while in the temperature range from 4 to 31 °C, the motion speed vs. loading frequency relations for three pavements were nearly identical. The loading frequency f increased approximately linearly with the motion speed V, according to the unified fitting equation for three types of pavements under study, namely f = 0.127 × V. This unified equation was further proved valid to predict the dynamic modulus properties of field asphalt pavement layers. Moreover, several previous prediction models for loading frequency, including the Brown model, Ullidtz model, MEPDG procedure and Ulloa model, were compared to the results in this study. These previous models were found to overestimate the loading frequencies within the asphalt layer. The prediction errors of the Brown model and the Ullidtz model were pronounced. The loading frequencies calculated by the MEPDG procedure and the Ulloa model need to be modified by dividing 2.8 and 1.7, respectively.

@en

The modulus of an asphalt layer subjected to repeated loadings was measured to reasonably analyze the damage development therein. The ratio of the reduction in the modulus to the modulus of the undamaged asphalt layer is used to reflect the damage of the asphalt layer; the evolution of the damage with the number of the loadings was analyzed. Full-scale accelerated pavement testing was conducted to simulate the repeated vehicle loadings on the asphalt layer. Falling-weight deflectometer, pavement seismic property analyzer (PSPA), and uniaxial compression dynamic modulus tests were conducted to obtain the modulus of the undamaged asphalt layer in the unloaded area. PSPA was used to obtain the moduli of the damaged asphalt layers in the loading area; the ratios of the reduction in these moduli to the modulus of the undamaged asphalt layer were calculated. The damage development in the asphalt layer was analyzed, and a nonlinear damage-evolution model was established, which assisted in obtaining the speed of the damage development in the asphalt layers at different depths. It is found that the S-type master curve can be used to unify the undamaged moduli derived from the three tests. The results of the field-detection method are in accordance with the predictions obtained from the laboratory master curves. In addition, the regression parameter in the damage-evolution model assists in judging the speed of the damage development in the asphalt layer. The normalization result shows that the lateral asphalt layer at the outer edge of the wheel paths and that at the center of the wheel gap experience slower damage as the depth increases. The mid-depth asphalt layers at the other positions and directions experience faster damage. In conclusion, the nonlinear damage-evolution model can provide the basis for damage development judgment and lay foundation for optimizing the maintenance timing and strategy.

@en

The temperature field of asphalt pavement with thick asphalt layer (>30 cm) was analyzed. Based on the cumulative effect of air temperature and solar radiation on pavement temperature, a regression analysis was conducted on the measured pavement temperature from four selected test sites and the obtained meteorological data. The prediction models for different sites were determined as a function of depth, average air temperature and total solar radiation. Then, the cause for the difference between the models at each site was analyzed, and the historical mean monthly air temperatures were incorporated into the model. The model can be applied to the pavement temperature prediction in different areas. The results show that the model has high applicability and high accuracy.

@en

To meet the high temperature and anti-reveling properties required in open-graded friction course, high content polymer modified asphalt (HCPMA) is gradually widely used in China, but the rheological, chemical and aging characteristic is not clear yet. In this paper, HCPMA with different SBS content and different base asphalt are prepared, and Pressure Aging Vessel (PAV) aging was conducted to simulate the long-term aging condition. The chemical and rheological evaluation of HCPMA before and after aging were tracked with Fourier transform infrared, gel permeation chromatography test, dynamic shear oscillatory test, master curve and multiple stress creep and recovery test. The results show that firstly, the aging of HCPMA is combined with hardening of asphalt and degradation of Styrene–butadiene–styrene (SBS) polymer. Furthermore, the addition of high content of SBS polymer can reduce the formation of carbonyl, but the degradation rate of SBS polymer is not related to the content of SBS or the type of base asphalt. Besides, HCPMA with a higher SBS content will have better rheological properties, but in consideration of economy, 9% is optimum dosage. At last, HCPMA prepared with Esso asphalt as base binder exhibits better rheological properties than HCPMA prepared with SK asphalt. However, the rheology difference reduces with the increase of SBS content and after PAV aging.

@en

Buton rock asphalt (BRA) is a natural asphalt modifier that can improve different properties of mixture. The traditional mixing process for BAR mixture is to mix aggregates with BRA firstly, and then mix them with heated base asphalt and mineral powder in that order. However, it results in an unevenness of asphalt film thickness, which can influence the performance of mixtures. Therefore, the primary objective of this research is to develop an advanced mixing process for BRA mixture. Six mixing processes were attempted. Air void, dynamic stability (DS), indirect tensile strength, and tensile strength ratio (TSR) were selected as the evaluation parameters. By comparison, the optimum mixing process is changed by adding the BRA and base asphalt in different orders. Lastly, contact angle measurements and inverse gas chromatography (IGC) were conducted to analyze the adhesion work in different mixing processes, which can explain the improvements of the advanced mixing process.@en

Temperature is one of the most important factors affecting functional as well as structural performance of asphalt pavements with thick asphalt layer (>30 cm). For a successful pavement design, it is vital to accurately predict the pavement temperatures at various depths. However, most previous researches focused on the temperature predictions for conventional asphalt pavements, of which the asphalt thickness is less than 30 cm. This suggests their proposed models are applicable in top layers, but may not be so effective for temperature predictions at deeper depths. As a result, the primary objective of this research was to develop a statistical model to predict temperatures at deep depths. Three test sites were selected, and they were instrumented with a number of sensors and a data logger to record the pavement temperature hourly. Also, all test sections can provide meteorological monitoring to collect hourly air temperatures and hourly total solar radiation. The recorded meteorological conditions were found to have cumulative effect on the measured pavement temperatures at various depths. On basis of their relationship, a statistical regression was performed, and the temperature prediction model was determined as a function of depth, average air temperature and total solar radiation calculated in the cumulative time. For an improvement in applicability, historical mean monthly air temperatures were also incorporated into the mode. The accuracy and applicability of the improved model were validated by applying it to additional sites for which the measured pavement temperatures and meteorological data were available. Also, by comparing with existing models, the developed model was testified to be more effective for asphalt pavements with thick asphalt layer, promising the model's potential use.

@en

Terminal Blend (TB) hybrid asphalt binders are composed of crumb rubber, SBS polymer and polyphosphoric acid (PPA). Understanding the relationship between the chemical composition and low temperature properties has a guiding significance for asphalt modification. In this study, BBR (Bending Beam Rheometer) test, GPC (Gel Permeation Chromatography) test, FTIR (Fourier Transform Infrared) test and DSC (Differential Scanning Calorimetry) test were used to evaluate the rheological and chemical properties of TB hybrid binder and TSRST (Thermal Stress Restrained Specimen test) was conducted to estimate the low temperature properties of mixture. The results indicated that crumb rubber and SBS improved low temperature properties, while PPA had an adverse effect. Furthermore, during the degradation of crumb rubber, aliphatic component was released, which played an important role in improving low temperature properties. Finally, TB hybrid asphalt mixture also had better low temperature properties than SBS modified asphalt mixtures according to TSRST results.

@en

Rutting is closely related to the pavement temperature field. As a result, using the concept of rutting equivalent temperature to predict rutting distress is a common method. Different from previous studies, this study puts forward a calculation method of the rutting equivalent temperature for asphalt pavement at different depth, which is based upon the pre-established prediction models of asphalt temperature field and rutting distress. Meanwhile, the rutting equivalent temperature prediction model considering regional differences and asphalt material properties is initially established and tested. Compared with the existing rutting equivalent temperature prediction model, the proposed model reflects the influences of different depth, different regions and different types of asphalt materials. It is demonstrated that this model has better applicability.

@en

Styrene-butadiene-styrene (SBS) is widely used in asphalt modification and the investigations about SBS modified asphalt are focused on high temperature property, storage stability and the compatibility between SBS and asphalt. While the study on influencing factors on low temperature properties are not sufficient yet. In this paper, a systematical research was conducted to evaluate the influencing level of important factors such as SBS polymer type, SBS content, sulfur content and addition of rubber processing oil. Firstly, bending beam rheometer (BBR) test associated with Burger's model was used to evaluate the low temperature property and relaxation capacity. Furthermore, FTIR, GPC and DSC tests were conducted to investigate the chemical changes in SBS modified asphalt. At last, the low temperature performance of SBS modified asphalt mixture was investigated with thermal stress restrained specimen test (TSRST). In this paper, the optimum modification scheme of SBS modified asphalt binder and mixture was investigated and summarized. SBS polymer is swollen by saturates and aromatics which made the base binder lack of maltene fraction. While the further addition of rubber processing oil supplemented the maltenes which improved the low temperature property.

@en

The determination of a single temperature to stimulate permanent deformation is quite significant in pavement design and maintenance. The practical use of this single temperature to replace the seasonal temperature fluctuation throughout the whole year can apparently simplify the prediction of permanent deformation of an asphalt pavement. This single temperature is termed effective temperature (T_eff) and is defined as a simulated temperature to achieve a permanent deformation, which is accumulated due to the traffic loading and pavement temperature within an entire year. However, most previous studies on effective temperature focus on investigating the performance temperature for permanent deformation instead of simplifying the prediction of this distress. For this reason, the primary goal of this study was to develop a T_eff model and simplify the prediction of permanent deformation of asphalt pavement. The predicted distress and the T_eff results used to build the models and find the optimized coefficients were obtained by the rut depth prediction model, which was based on shear stress and widely applied in China. The proposed T_eff models incorporated degree-days and the earth temperature, which was represented by mean annual air temperature (MAAT). By incorporating those parameters, these temperature models predominantly considered the effect of high temperature on the permanent deformation and can be utilized to improve their prediction in various regions. In addition, the asphalt mixture properties and vehicle speeds were also incorporated in the models. By comparing with different models in previous studies, the proposed models were testified to be reasonable.

@en