Many superconducting on-chip filter-banks suffer from poor coupling to the detectors behind each filter. This is a problem intrinsic to the commonly used half-wavelength filter, which has a maximum theoretical coupling of 50 %. In this paper, we introduce a phase-coherent filter, called a directional filter, which has a theoretical coupling of 100 %. In order to study and compare different types of filter-banks, we first analyze the measured filter frequency scatter, losses, and spectral resolution of a DESHIMA 2.0 filter-bank chip. Based on measured fabrication tolerances and losses, we adapt the input parameters for our circuit simulations, quantitatively reproducing the measurements. We find that the frequency scatter is caused by nanometer-scale line width variations and that variances in the spectral resolution is caused by losses in the dielectric only. Finally, we include these realistic parameters in a full filter-bank model and simulate a wide range of spectral resolutions and oversampling values. For all cases, the directional filter-bank has significantly higher coupling to the detectors than the half-wave resonator filter-bank. The directional filter eliminates the need to use oversampling as a method to improve the total efficiency, instead capturing nearly all the power remaining after dielectric losses.

@en

Context. Integrated superconducting spectrometers (ISSs) for wide-band submillimeter (submm) astronomy use quasi-optical systems for coupling radiation from the telescope to the instrument. Misalignment in these systems is detrimental to the system performance. The common method of using an optical laser to align the quasi-optical components requires an accurate alignment of the laser to the submm beam from the instrument, which is not always guaranteed to a sufficient accuracy. Aims. We develop an alignment strategy for wide-band ISSs that directly uses the submm beam of the wide-band ISS. The strategy should be applicable in both telescope and laboratory environments. Moreover, the strategy should deliver similar quality of the alignment across the spectral range of the wide-band ISS. Methods. We measured the misalignment in a quasi-optical system operating at submm wavelengths using a novel phase and amplitude measurement scheme that is capable of simultaneously measuring the complex beam patterns of a direct-detecting ISS across a harmonic range of frequencies. The direct detection nature of the microwave kinetic inductance detectors in our device-under-test, DESHIMA 2.0, necessitates the use of this measurement scheme. Using geometrical optics, the measured misalignment, a mechanical hexapod, and an optimisation algorithm, we followed a numerical approach to optimise the positioning of corrective optics with respect to a given cost function. Laboratory measurements of the complex beam patterns were taken across a harmonic range between 205 and 391 GHz and were simulated through a model of the ASTE telescope in order to assess the performance of the optimisation at the ASTE telescope. Results. Laboratory measurements show that the optimised optical setup corrects for tilts and offsets of the submm beam. Moreover, we find that the simulated telescope aperture efficiency is increased across the frequency range of the ISS after the optimisation.

@en

In this article, the wrong figure appeared as Figures 1 and 2; the figure should have appeared as shown below Figure 1 (right side of the figure only): (Figure presented.) Figure 2: (Figure presented.)

@en

Terahertz Integral Field Unit with Universal Nanotechnology (TIFUUN) is a wideband spectral mapper operating at (sub)-millimeter wavelengths. The instrument is under development for ground-based astronomy and will be deployed to the ASTE telescope in Chile. In this work, the building blocks for TIFUUN’s wideband (2:1) mappers are discussed. These components are based on multi-lens focal plane arrays of leaky lens antennas coupled to filter banks based on Microwave Kinetic Inductance Detectors.@en

Photonic technologies offer numerous functionalities that can be used to realize astrophotonic instruments. The most spectacular example to date is the ESO Gravity instrument at the Very Large Telescope in Chile that combines the light-gathering power of four 8 m telescopes through a complex photonic interferometer. Fully integrated astrophotonic devices stand to offer critical advantages for instrument development, including extreme miniaturization when operating at the diffraction-limit, as well as integration, superior thermal and mechanical stabilization owing to the small footprint, and high replicability offering significant cost savings. Numerous astrophotonic technologies have been developed to address shortcomings of conventional instruments to date, including for example the development of photonic lanterns to convert from multimode inputs to single mode outputs, complex aperiodic fiber Bragg gratings to filter OH emission from the atmosphere, complex beam combiners to enable long baseline interferometry with for example, ESO Gravity, and laser frequency combs for high precision spectral calibration of spectrometers. Despite these successes, the facility implementation of photonic solutions in astronomical instrumentation is currently limited because of (1) low throughputs from coupling to fibers, coupling fibers to chips, propagation and bend losses, device losses, etc, (2) difficulties with scaling to large channel count devices needed for large bandwidths and high resolutions, and (3) efficient integration of photonics with detectors, to name a few. In this roadmap, we identify 24 key areas that need further development. We outline the challenges and advances needed across those areas covering design tools, simulation capabilities, fabrication processes, the need for entirely new components, integration and hybridization and the characterization of devices. To realize these advances the astrophotonics community will have to work cooperatively with industrial partners who have more advanced manufacturing capabilities. With the advances described herein, multi-functional integrated instruments will be realized leading to novel observing capabilities for both ground and space based platforms, enabling new scientific studies and discoveries.

@en

Advances in far infrared astronomy have been, and will be, defined by instrument capabilities. Especially relevant is the development of imaging spectrometers for the wavelength range of 0.03-3 mm, which are not available at all at this moment. We will discuss recent advances in this field: First, we discuss the development of miniature on-chip spectrometers, that can operate in a 0.09-1 THz by using lossless superconducting circuits to create miniature spectrometers. For higher frequencies this is not possible due to material limitations, moreover instruments have to be operated in space due to the opacity of the atmosphere. Recent proposals for new missions focus on space-based observatories with optics cooled down to 4K, which offer unprecedented spectral imaging speeds, but require large arrays of extremely sensitive detectors. In the second part of this paper we will discuss the development of microwave Kinetic Inductance detectors with a sensitivity of NEP. 3.1.10-20 W/ãHz, sufficient for these applications.@en

We present a feasibility study for the high-redshift galaxy part of the Science Verification Campaign with the 220–440 GHz deshima 2.0 integrated superconducting spectrometer on the ASTE telescope. The first version of the deshima 2.0 chip has been recently manufactured and tested in the lab. Based on these realistic performance measurements, we evaluate potential target samples and prospects for detecting the [CII] and CO emission lines. The planned observations comprise two distinct, but complementary objectives: (1) acquiring spectroscopic redshifts for dusty galaxies selected in far-infrared/mm-wave surveys; (2) multi-line observations to infer physical conditions in dusty galaxies.

@en

Superconducting resonators and transmission lines are fundamental building blocks of integrated circuits for millimeter-submillimeter astronomy. Accurate simulation of radiation loss from the circuit is crucial for the design of these circuits because radiation loss increases with frequency, and can thereby deteriorate the system performance. Here we show a stratification for a 2.5-dimensional method-of-moment simulator Sonnet EM that enables accurate simulations of the radiative resonant behavior of submillimeter-wave coplanar resonators and straight coplanar waveguides (CPWs). The Sonnet simulation agrees well with the measurement of the transmission through a coplanar resonant filter at 374.6 GHz. Our Sonnet stratification utilizes artificial lossy layers below the lossless substrate to absorb the radiation, and we use co-calibrated internal ports for de-embedding. With this type of stratification, Sonnet can be used to model superconducting millimeter-submillimeter wave circuits even when radiation loss is a potential concern.

@en

Low-loss deposited dielectrics will benefit superconducting devices such as integrated superconducting spectrometers, superconducting qubits, and kinetic inductance parametric amplifiers. Compared with planar structures, multilayer structures such as microstrips are more compact and eliminate radiation loss at high frequencies. Multilayer structures are most easily fabricated with deposited dielectrics, which typically exhibit higher dielectric loss than crystalline dielectrics. We measure the subkelvin and low-power microwave and millimeter-submillimeter-wave dielectric loss of hydrogenated amorphous silicon carbide (a-SiC:H), using superconducting chips with Nb-Ti-N/a-SiC:H/Nb-Ti-N microstrip resonators. We deposit the a-SiC:H by plasma-enhanced chemical vapor deposition at a substrate temperature of 400°C. The a-SiC:H has a millimeter-submillimeter loss tangent ranging from 0.9×10-4 at 270 GHz to 1.5×10-4 at 385 GHz. The microwave loss tangent is 3.1×10-5. These are the lowest low-power subkelvin loss tangents that have been reported for microstrip resonators at millimeter-submillimeter and microwave frequencies. The a-SiC:H films are free of blisters and have low stress: -20 MPa compressive at 200-nm thickness to 60 MPa tensile at 1000-nm thickness.

@en

The next technological breakthrough in millimeter–submillimeter astronomy is three-dimensional imaging spectrometry with wide instantaneous spectral bandwidths and wide fields of view. The total optimization of the focal-plane instrument, the telescope, the observing strategy, and the signal-processing software must enable efficient removal of foreground emission from the Earth’s atmosphere, which is time-dependent and highly nonlinear in frequency. Here, we present Time-dependent End-to-end Model for Post-process Optimization (TiEMPO) of the DEep Spectroscopic HIgh-redshift MApper (DESHIMA) spectrometer. TiEMPO utilizes a dynamical model of the atmosphere and parameterized models of the astronomical source, the telescope, the instrument, and the detector. The output of TiEMPO is a time stream of sky brightness temperature and detected power, which can be analyzed by standard signal-processing software. We first compare TiEMPO simulations with an on-sky measurement by the wideband DESHIMA spectrometer, and find good agreement in the noise and sensitivity. We then use TiEMPO to simulate the detection of the line emission spectrum of a high-redshift galaxy using the DESHIMA 2.0 spectrometer in development. The TiEMPO model is open source. Its modular and parametrized design enables users to adapt it to optimize the end-to-end performance of spectroscopic and photometric instruments on existing and future telescopes

@en

Integrated superconducting spectrometer (ISS) technology will enable ultra-wideband, integral-field spectroscopy for (sub)millimeter-wave astronomy, in particular, for uncovering the dust-obscured cosmic star formation and galaxy evolution over cosmic time. Here, we present the development of DESHIMA 2.0, an ISS for ultra-wideband spectroscopy toward high-redshift galaxies. DESHIMA 2.0 is designed to observe the 220–440 GHz band in a single shot, corresponding to a redshift range of z = 3.3–7.6 for the ionized carbon emission ([C II] 158 μ m). The first-light experiment of DESHIMA 1.0, using the 332–377 GHz band, has shown an excellent agreement among the on-sky measurements, the laboratory measurements, and the design. As a successor to DESHIMA 1.0, we plan the commissioning and the scientific observation campaign of DESHIMA 2.0 on the ASTE 10-m telescope in 2023. Ongoing upgrades for the full octave-bandwidth system include the wideband 347-channel chip design and the wideband quasi-optical system. For efficient measurements, we also develop the observation strategy using the mechanical fast sky-position chopper and the sky-noise removal technique based on a novel data-scientific approach. In the paper, we show the recent status of the upgrades and the plans for the scientific observation campaign.

@en

Superconducting circuit elements used in millimeter-submillimeter (mm-submm) astronomy would greatly benefit from deposited dielectrics with small dielectric loss and noise. This will enable the use of multilayer circuit elements and thereby increase the efficiency of mm-submm filters and allow for a miniaturization of microwave kinetic inductance detectors (MKIDs). Amorphous dielectrics introduce excess loss and noise compared with their crystalline counterparts, due to two-level system defects of unknown microscopic origin. We deposited hydrogenated amorphous silicon films using plasma-enhanced chemical vapor deposition, at substrate temperatures of 100°C, 250°C, and 350°C. The measured void volume fraction, hydrogen content, microstructure parameter, and bond-Angle disorder are negatively correlated with the substrate temperature. All three films have a loss tangent below 10-5 for a resonator energy of 105 photons, at 120 mK and 4 to 7 GHz. This makes these films promising for MKIDs and on-chip mm-submm filters.

@en

We present a "mix-and-match"process to create large structures with submicrometer features by combining UV contact lithography and 100 kV electron-beam lithography in a single layer of negative-tone resist: Micro-Resist-Technology ma-N1405. The resist is successfully applied for the fabrication of an on-chip terahertz spectrometer, where the design requires 450 nm wide lines and 300 nm wide trenches in a 150 nm thick niobium-titanium-nitride layer, tolerating errors of ± 30 nm. We use a resist thickness of 500 nm, optimized to allow reliable SF 6/O 2-based reactive ion etching of structures with 30 nm accuracy. We find that resist requires an electron-beam cross-linking dose of 1100 μ C / c m 2 for an acceleration voltage of 100 kV in combination with a 180 s 100 °C bake on a hot plate and 45 s development. The smallest resist bars made with our dedicated recipe are 100 nm wide, with the smallest gaps about 300 nm. The difference between the designed and realized feature size is between 2 and 30 nm for structures up to 700 nm wide. The optical exposure dose is 300 m J / c m 2 for the same development time and is optimized to produce a positive sloped edge profile allowing good step coverage for subsequent layers. The resist can be applied, shipped, and processed in a time span of a couple of days without notable deterioration of patterning quality.

@en

We present a lab-on-chip experiment to accurately measure losses of superconducting microstrip lines at microwave and submillimeter wavelengths. The microstrips are fabricated from Nb-Ti-N, which is deposited using reactive magnetron sputtering, and amorphous silicon which is deposited using plasma-enhanced chemical vapor deposition (PECVD). Submillimeter wave losses are measured using on-chip Fabry-Perot resonators (FPRs) operating around 350 GHz. Microwave losses are measured using shunted half-wave resonators with an identical geometry and fabricated on the same chip. We measure a loss tangent of the amorphous silicon at single-photon energies of tan⁡δ=3.7±0.5×10-5 at approximately 6GHz and tan⁡δ=2.1±0.1×10-4 at 350 GHz. These results represent very low losses for deposited dielectrics, but the submillimeter wave losses are significantly higher than the microwave losses, which cannot be understood using the standard two-level system loss model.

@en

A superconducting microstrip half-wavelength resonator is proposed as a suitable band-pass filter for broadband moderate spectral resolution spectroscopy for terahertz (THz) astronomy. The proposed filter geometry has a free spectral range of an octave of bandwidth without introducing spurious resonances, reaches a high coupling efficiency in the pass-band and shows very high rejection in the stop-band to minimize reflections and cross-talk with other filters. A spectrally sparse prototype filter-bank in the band 300400 GHz has been developed employing these filters as well as an equivalent circuit model to anticipate systematic errors. The fabricated chip has been characterized in terms of frequency response, reporting an average peak coupling efficiency of 27% with an average spectral resolution of 940.

@en

This paper discusses the science case for a sensitive spectro-polarimetric survey of the microwave sky. Such a survey would provide a tomographic and dynamic census of the three-dimensional distribution of hot gas, velocity flows, early metals, dust, and mass distribution in the entire Hubble volume, exploit CMB temperature and polarisation anisotropies down to fundamental limits, and track energy injection and absorption into the radiation background across cosmic times by measuring spectral distortions of the CMB blackbody emission. In addition to its exceptional capability for cosmology and fundamental physics, such a survey would provide an unprecedented view of microwave emissions at sub-arcminute to few-arcminute angular resolution in hundreds of frequency channels, a data set that would be of immense legacy value for many branches of astrophysics. We propose that this survey be carried out with a large space mission featuring a broad-band polarised imager and a moderate resolution spectro-imager at the focus of a 3.5 m aperture telescope actively cooled to about 8K, complemented with absolutely-calibrated Fourier Transform Spectrometer modules observing at degree-scale angular resolution in the 10–2000 GHz frequency range. We propose two observing modes: a survey mode to map the entire sky as well as a few selected wide fields, and an observatory mode for deeper observations of regions of specific interest.

@en

A superconducting on-chip microstrip filter bank spectrometer prototype for Far-Infrared (FIR) Astronomy is presented. The measurements showcase its capabilities towards moderate spectral resolution (f/\Delta f\sim 500) broadband FIR spectroscopy. In this sub-mm-wave filter bank, each spectral channel consists of an 'I-shaped' microstrip THz bandpass filter that couples the radiation to a Microwave Kinetic Inductance Detector (MKID) for a background limited detection and a scalable frequency-multiplexed microwave readout.

@en

The integrated superconducting spectrometer (ISS) enables ultra-wideband, large field-of-view integral-field-spectrometer designs for mm-submm wave astronomy. DESHIMA (Deep Spectroscopic High-redshift Mapper) is a single-pixel ISS spectrometer for the ASTE 10-m telescope, designed to observe the 220-440 GHz band in a single shot, corresponding to a [CII]-line redshift range of z=3.3-7.6.In this colloquium I will present the instrument concept, design, and first on-sky results of DESHIMA, obtained from October to December 2017 on the ASTE telescope. On the ISS chip of DESHIMA, the signal is captured by a lens-antenna and subsequently travels through a coplanar waveguide made of superconducting NbTiN, from which NbTiN bandpass filters branch out to divide the signal into separate frequency channels. At the output of each filter is a NbTiN/Al hybrid microwave kinetic inductance detector (MKID). The first generation of DESHIMA (DESHIMA 1.0) is a 1-pixel spectrometer that covers the 332-377 GHz band with 49 spectral channels, offering a spectral resolution F/dF ~ 380. We present detection of molecular emission lines from various sources, including a weakly redshifted CO line from the luminous infrared galaxy VV 114. The on-sky performance shows excellent agreement between the design and laboratory measurement in terms of the sensitivity, optical efficiency and beam pattern. In addition, we present wideband spectral maps of extended sources to demonstrate the potential of the ISS technology towards spectroscopic direct imaging. Ongoing upgrades towards the octave-bandwidth full system (DESHIMA 2.0) include the development of a filterbank chip with ~350 channels and higher optical efficiency, a wideband quasioptical design, and observing methods for efficiently removing the atmosphere. DESHIMA is a collaboration between the Netherlands (TU Delft, SRON, Leiden University, +) and Japan (University of Tokyo, Nagoya University, Kitami Institute of Technology, NAOJ, +) Reference Endo et al., "First light demonstration of the integrated superconducting spectrometer," Nature Astronomy 3, 989-996 (2019) https://arxiv.org/abs/1906.10216 DESHIMA website: http://deshima.ewi.tudelft.nl @en