Nowadays, Sn-based electrocatalysts for the electrochemical CO2 reduction reaction (eCO2RR) toward formic acid have been reported to reach industrially relevant current densities and Faradaic efficiencies approaching 100%. However, electrocatalyst stability remains inadequate and appears to be a crucial piece to the puzzle, as lifetimes in the range of several thousands of hours should be reached for practical application and economic viability. Here, we provide insights into stability issues related to Sn-based electrocatalysts and electrolyzers for formic acid production. By determining the chemical and physical phenomena that occur during the electrochemical reduction reaction on the surface and bulk of Sn-based catalysts, we intend to elucidate the most common degradation mechanisms that impair long-term electrocatalytic activity of these catalysts. Moreover, highlighting the importance of correctly selected process conditions and an optimized reactor design allows us to unveil all necessary aspects for a stable Sn-based eCO2RR toward formic acid.

Direct electrochemical reduction of CO2 to C2 products such as ethylene is more efficient in alkaline media, but it suffers from parasitic loss of reactants due to (bi)carbonate formation. A two-step process where the CO2 is first electrochemically reduced to CO and subsequently converted to desired C2 products has the potential to overcome the limitations posed by direct CO2 electroreduction. In this study, we investigated the technical and economic feasibility of the direct and indirect CO2 conversion routes to C2 products. For the indirect route, CO2 to CO conversion in a high temperature solid oxide electrolysis cell (SOEC) or a low temperature electrolyzer has been considered. The product distribution, conversion, selectivities, current densities, and cell potentials are different for both CO2 conversion routes, which affects the downstream processing and the economics. A detailed process design and techno-economic analysis of both CO2 conversion pathways are presented, which includes CO2 capture, CO2 (and CO) conversion, CO2 (and CO) recycling, and product separation. Our economic analysis shows that both conversion routes are not profitable under the base case scenario, but the economics can be improved significantly by reducing the cell voltage, the capital cost of the electrolyzers, and the electricity price. For both routes, a cell voltage of 2.5 V, a capital cost of $10,000/m2, and an electricity price of <$20/MWh will yield a positive net present value and payback times of less than 15 years. Overall, the high temperature (SOEC-based) two-step conversion process has a greater potential for scale-up than the direct electrochemical conversion route. Strategies for integrating the electrochemical CO2/CO conversion process into the existing gas and oil infrastructure are outlined. Current barriers for industrialization of CO2 electrolyzers and possible solutions are discussed as well.

A zero-gap flow electrolyzer with a tin-coated gas diffusion electrode as the cathode was used to convert humidified gaseous CO₂ to formate. The influence of humidification, flow pattern and the type of membrane on the faradaic efficiency (FE), product concentration, and salt precipitation were investigated. We demonstrated that water management in the gas diffusion electrode was crucial to avoid flooding and (bi)carbonate precipitation, to uphold a high FE and formate concentration. Direct water injection was validated as a novel approach for water management. At 100 mA/cm², direct water injection in combination with an interdigitated flow channel resulted in a FE of 80 % and a formate concentration of 65.4+/−0.3 g/l without salt precipitation for a prolonged CO₂ electrolysis of 1 h. The use of bipolar membranes in the zero-gap configuration mainly produced hydrogen. These results are important for the design of commercial scale CO₂ electrolyzers.

We use a high-pressure semicontinuous batch electrochemical reactor with a tin-based cathode to demonstrate that it is possible to efficiently convert CO₂ to formic acid (FA) in low-pH (i.e., pH < pK_a) electrolyte solutions. The effects of CO₂ pressure (up to 50 bar), bipolar membranes, and electrolyte (K₂SO₄) concentration on the current density (CD) and the Faraday efficiency (FE) of formic acid were investigated. The highest FE (?80%) of FA was achieved at a pressure of around 50 bar at a cell potential of 3.5 V and a CD of ?30 mA/cm². To suppress the hydrogen evolution reaction (HER), the electrochemical reduction of CO₂ in aqueous media is typically performed at alkaline conditions. The consequence of this is that products like formic acid, which has a pK_a of 3.75, will almost completely dissociate into the formate form. The pH of the electrolyte solution has a strong influence not only on the electrochemical reduction process of CO₂ but also on the downstream separation of (dilute) acid products like formic acid. The selection of separation processes depends on the dissociation state of the acids. A review of separation technologies for formic acid/formate removal from aqueous dilute streams is provided. By applying common separation heuristics, we have selected liquid-liquid extraction and electrodialysis for formic acid and formate separation, respectively. An economic evaluation of both separation processes shows that the formic acid route is more attractive than the formate one. These results urge for a better design of (1) CO₂ electrocatalysts that can operate at low pH without affecting the selectivity of the desired products and (2) technologies for efficient separation of dilute products from (photo)electrochemical reactors.