Flooding is expected to increase due to climate change, urbanisation, and land use change. To address this issue, Nature-Based Solutions (NBSs) are often adopted as innovative and sustainable flood risk management methods. Besides the flood risk reduction benefits, NBSs offer co-benefits for the environment and society. However, these co-benefits are rarely considered in flood risk management due to the inherent complexities of incorporating them into economic assessments. This research addresses this gap by developing a comprehensive methodology that integrates the monetary analysis of co-benefits with flood risk reduction in economic assessments. In doing so, it aspires to provide a more holistic view of the impact of NBS in flood risk management. The assessment employs a framework based on life-cycle cost-benefit analysis, offering a systematic and transparent assessment of both costs and benefits over time supported by key indicators like net present value and benefit cost ratio. The methodology has been applied to the Tamnava basin in Serbia, where significant flooding occurred in 2014 and 2020. The methodology offers valuable insights for practitioners, researchers, and planners seeking to assess the co-benefits of NBS and integrate them into economic assessments. The results show that when considering flood risk reduction alone, all considered measures have higher costs than the benefits derived from avoiding flood damage. However, when incorporating co-benefits, several NBS have a net positive economic impact, including afforestation/reforestation and retention ponds with cost-benefit ratios of 3.5 and 5.6 respectively. This suggests that incorporating co-benefits into economic assessments can significantly increase the overall economic efficiency and viability of NBS.

@en

Low-lying coastal cities are vulnerable to compound floods caused by many factors including river flows, tides and local rainfall. Many previous studies focus on the impacts of rainfall and tidal levels (two driving factors) on estuaries or regions near the main single river, while research about the three influencing factors on the floods for complex urban river networks remain relatively scarce. This paper proposes a framework to simulate the coastal compound flooding process, with a series of scenarios designed to explore the main flooding drivers and their worst possible combination. The approach is used to quantify the induced flooding consequences, in which a two-dimensional model is employed to conduct a case study for a city with complex river networks. The Qianshan River basin in Zhuhai City, located in the Guangdong-Hong Kong-Macao Greater Bay Area (GBA) of China is used as the case study. Application results show that: (i) the occurrence and properties of flooding in this coastal area are jointly affected by upstream river flows, downstream tidal levels and local rainfall intensity with different contribution levels, (ii) compared to tidal levels, local rainfall intensity has a larger impact on the flooding levels of the study region, and (iii) the worst scenario where a 50-year return period upstream river flow co-occurring with high tide and a 100-year return period rainfall can produce a flooding area up to 50 km² for the study region, with an average of 1.3 m flooded depth. The proposed framework with its findings offers an in-depth understanding and quantification of coastal urban flood characteristics within the GBA of China.

@en

Bursts in water distribution systems (WDSs) lead to water wastage and negative environmental impacts. Optimizing pressure sensor placement (PSP) for effective burst detection is crucial for prompt response and adverse event mitigation. While many optimization methods are available for this purpose, their resulting PSP strategies often exhibit large variability caused by background noise or metering accuracy, representing low robustness. This consequently hinders the wide application of existing PSP methods for burst detection in WDSs. This study proposes a novel multi-objective PSP method aimed at maximizing burst detection while minimizing the number of sensors. Within this method, a new threshold metric is introduced to quantify the minimum detectable burst outflow across all pipes. The metric has the key advantage of taking into account the fact that the relative magnitude of the detectable threshold for different pipes is independent of noise, thereby addressing the low robustness issue. The proposed method is applied to three WDSs, and results show that it can consistently achieve robust optimal PSP strategies across diverse noise conditions. Comprehensive comparisons between the proposed method and the other benchmark approaches are conducted using five metrics, including detection performance and layout characteristics. These comparisons reveal the properties of each optimization method and show how detection performance is affected by various placement features. It is anticipated that the proposed method can be useful in engineering practice due to its great robustness in determining the optimal PSP strategies for burst detection in WDSs compared to other alternatives.@en

Isolation valve closures (IVCs) can effectively assist pipe maintenance and management in water distribution systems (WDSs), but they inevitably cause secondary impacts on the WDS’s performance. Previous studies have mainly focused on how to optimally operate or locate valves, but few efforts have been made on investigating the secondary impacts induced by IVCs. To this end, six quantitative metrics are proposed to comprehensively evaluate physical, hydraulic, and water quality impacts caused by IVCs. These metrics are used to explore how different network topologies, valve closing strategies, and valve placement strategies affect an IVC’s overall impact on WDS performance. Applications to three real WDSs show the following: (1) the proposed metrics can effectively reveal underlying impacts caused by IVCs, especially the associated water quality risk that has rarely been considered before; (2) in addition to their surrounding pipes, IVCs can affect the water quality in pipes that are far away from the isolated segments; (3) a highly looped WDS is more likely to have higher water quality risk (e.g., due to flow direction reversal) but a lower hydraulic influence level (e.g., low pressure) compared to a WDS with many branched structures; and (4) while closing valves near the failed pipe is an overall strategy to reduce hydraulic impacts, it may also produce high water quality risk. The proposed metrics and the assessment framework are practically meaningful as they offer not only an improved understanding of the secondary impacts caused by IVCs, but also guidance for the decision-making process regarding valve maintenance and management.@en

Water distribution networks (WDNs) are a vital component of urban water infrastructure. They transport water from production sites (sources) to spatially distributed consumers (sinks). Multiobjective optimization procedures are often used to minimize construction costs and at the same time maximize the resilience of such systems, which is usually a very computationally expensive task. Recently, highly efficient approaches based on complex network analysis (CNA) have been developed to solve this task more computationally efficiently. With CNA, very large WDNs can be optimized, considering network topology and demand distribution (using, e.g., demand edge betweenness centrality). However, existing CNA approaches do not consider network topography (i.e., height differences between sources and sinks). Comparing design solutions based on CNA with those found by evolutionary algorithms shows that the least-cost CNA design cannot compete with the latter. In this work, a hybrid approach is developed, where low-cost design CNA solutions are evaluated with a hydraulic solver (Epanet2), and subsequently the demand edge betweenness centrality distribution is iteratively altered for nodes with pressure deficits. This enhanced CNA-based optimization is tested on two different large case studies from the literature and shows promising results (2% cost increase). These solutions were obtained using significantly less computational effort (at least factor 1,000 faster), enabling solving very large WDN optimization problems (>150,000 decision variables).

@en

Wastewater-based epidemiology (WBE) has been proven to be a useful tool in monitoring public health-related issues such as drug use, and disease. By sampling wastewater and applying WBE methods, wastewater-detectable pathogens such as viruses can be cheaply and effectively monitored, tracking people who might be missed or under-represented in traditional disease surveillance. There is a gap in current knowledge in combining hydraulic modeling with WBE. Recent literature has also identified a gap in combining machine learning with WBE for the detection of viral outbreaks. In this study, we loosely coupled a physically-based hydraulic model of pathogen introduction and transport with a machine learning model to track and trace the source of a pathogen within a sewer network and to evaluate its usefulness under various conditions. The methodology developed was applied to a hypothetical sewer network for the rapid detection of disease hotspots of the disease caused by the SARS-CoV-2 virus. Results showed that the machine learning model's ability to recognize hotspots is promising, but requires a high time-resolution of monitoring data and is highly sensitive to the sewer system's physical layout and properties such as flow velocity, the pathogen sampling procedure, and the model's boundary conditions. The methodology proposed and developed in this paper opens new possibilities for WBE, suggesting a rapid back-tracing of human-excreted biomarkers based on only sampling at the outlet or other key points, but would require high-frequency, contaminant-specific sensor systems that are not available currently.

@en

Under global climate change, urban flooding occurs frequently, leading to huge economic losses and human casualties. Extreme rainfall is one of the direct and key causes of urban flooding, and accurate rainfall estimates at high spatiotemporal resolution are of great significance for real-time urban flood forecasting. Using existing rainfall intensity measurement technologies, including ground rainfall gauges, ground-based radar, and satellite remote sensing, it is challenging to obtain estimates of the desired quality and resolution. However, an approach based on processing distributed surveillance camera network imagery through machine learning algorithms to estimate rainfall intensities shows considerable promise. Here, we present a novel approach that first extracts raindrop information from the surveillance camera images (rather than using the raw imagery directly), followed by the use of convolutional neural networks to estimate rainfall intensity from the resulting raindrop information. Evaluation of the approach on 12 rainfall events under both daytime and nighttime conditions shows that generalization ability, and especially nighttime predictive performance, is significantly improved. This represents an important step toward achieving real-time, high spatiotemporal resolution, measurement of urban rainfall at relatively low cost.

@en

Biofilm detachment contributes to water quality deterioration. However, the contributions of biofilm detachment from different pipes have not been quantified or compared. Following the introduction of partial reverse osmosis (RO) in drinking water production, this study analyzed particles at customers’ ends and tracked their origins to water distribution mains and service lines. For doing so, filter bags were installed in front of water meters to capture upstream detached particles, while biofilm from water main and service line were sampled by cutting pipe specimens. The results showed that elemental concentrations of the biofilm in mains were higher than those of service lines (54.3–268.5 vs. 27.1–44.4 μg/cm2), both dominated by Ca. Differently, filter bags were dominated by Fe/Mn (77.5–98.1%). After introducing RO, Ca significantly decreased in biofilms of mains but not service lines, but the released Fe/Mn rather than Ca arrived at customers’ ends. The ATP concentrations of service lines were higher than mains, which decreased on mains but increased in service lines after introducing RO. For the core ASVs, 13/24 were shared by service lines (17), mains (21), and filter bags (17), which were assigned mainly to Nitrospira spp., Methylomagnum spp., Methylocytis spp., and IheB2–23 spp. According to source tracking results, service lines contributed more than mains to the particulate material collected by filter bags (57.6 ± 13.2% vs. 13.0 ± 11.6%). To the best of our knowledge, the present study provides the first evidence of service lines’ direct and quantitative contributions to potential water quality deterioration at customers’ ends. This highlights the need for the appropriate management of long-neglected service line pipes, e.g., regarding material selection, length optimization, and proper regulation.@en

Urban drainage models (UDMs) are often used to manage urban flooding. However, these models generally involve many parameters to represent the underlying complex hydrodynamic processes. This results in significant challenges to achieving effective and robust model calibration especially with frequently limited observations, leading to unreliable model predictions. This paper makes the first attempt at UDM calibration using the Bayesian-based Ensemble Smoother (ES) method. Three ES variants are considered, that is, the primary ES, the versions with multiple data assimilation (ES-MDA) and iterative local update (ES-ILU). Two synthetic cases and one real-world application with up to 5,236 calibration parameters are tested. Results obtained show that: (a) both ES-MDA and ES-ILU can produce effective model calibration with ES-ILU outperforming ES-MDA in terms of both accuracy and uncertainty while ES exhibits limited performance; (b) for the real-world case, both the ES-MDA and ES-ILU methods provide better calibration results than the best-known solution manually obtained, (c) a minimum number of observations are required to enable an overall accurate model calibration (e.g., four and ten more monitoring sites are needed in the two synthetic cases); and (d) the model calibrated using an intense rainfall event is generally robust to make reliable predictions across different rainfall events while the model calibrated using less intense rainfall event does not perform well for more intense rainfall events. It was also found that ubiquitous parameter equifinality significantly hinders unique parameter identification even when overall accurate state estimates are obtained. This should be clearly understood in practical applications.

@en

Urban flooding is a major issue worldwide, causing huge economic losses and serious threats to public safety. One promising way to mitigate its impacts is to develop a real-time flood risk management system; however, building such a system is often challenging due to the lack of high spatiotemporal rainfall data. While some approaches (i.e., ground rainfall stations or radar and satellite techniques) are available to measure and/or predict rainfall intensity, it is difficult to obtain accurate rainfall data with a desirable spatiotemporal resolution using these methods. This paper proposes an image-based deep learning model to estimate urban rainfall intensity with high spatial and temporal resolution. More specifically, a convolutional neural network (CNN) model called the image-based rainfall CNN (irCNN) model is developed using rainfall images collected from existing dense sensors (i.e., smart phones or transportation cameras) and their corresponding measured rainfall intensity values. The trained irCNN model is subsequently employed to efficiently estimate rainfall intensity based on the sensors’ rainfall images. Synthetic rainfall data and real rainfall images are respectively utilized to explore the irCNN's accuracy in theoretically and practically simulating rainfall intensity. The results show that the irCNN model provides rainfall estimates with a mean absolute percentage error ranging between 13.5% and 21.9%, which exceeds the performance of other state-of-the-art modeling techniques in the literature. More importantly, the main feature of the proposed irCNN is its low cost in efficiently acquiring high spatiotemporal urban rainfall data. The irCNN model provides a promising alternative for estimating urban rainfall intensity, which can greatly facilitate the development of urban flood risk management in a real-time manner.

@en

Most of the contamination source localization methods for water distribution systems (WDSs) assume the availability of accurate water quality models and multi-parameter online sensors, which are often out of reach of many water utilities. To address this, a novel manual grab-sampling method (MGSM) is developed to effectively and efficiently locate continuous contamination sources in a WDS using a dynamic and cyclical sampling strategy. The grab samples are collected at a pre-specified number of hydrants by the corresponding teams followed by laboratory tests. The MGSM optimizes the sampling plan at each cycle by making the probability of contamination source(s) in each sub-network as equal as possible, where sub-networks are determined by the selected hydrants and current flow pipe directions. The CS's size is reduced at each cycle by exploiting sample testing results obtained in the previous cycle until there are no further hydrants to sample from. Two real-world WDSs are used to demonstrate the effectiveness of the proposed MGSM. The results obtained show that the MGSM can significantly reduce the spatial range of the CS (to about 5% of the entire WDS) for a range of scenarios including multiple contamination sources and pipe flow direction changes. We found that an optimal number of sampling teams exists for a given WDS, representing a balanced trade-off between detection efficiency and sampling/testing budgets. Due to its relative simplicity, the proposed MGSM can be used in engineering practice straightaway and it represents a viable alternative to the methods associated with water quality models and sensors.

@en

An early contamination warning system with deployed water quality sensors is often used to enhance the safety of a water distribution system (WDS). While algorithms have been developed to select an optimal water quality sensor placement strategy (WQSPS) for WDSs, many of them do not account for the influences caused by future uncertainties, such as sensor failures and system changes (e.g., demand variations and configuration/expansion changes in the WDS). To this end, this paper proposes a comprehensive framework to evaluate the robustness of WQSPSs to these possible uncertainties. This is achieved by considering five different performance objectives of WQSPSs as well as possible future demand and typology variations of WDSs under a wide range of sensor failure scenarios. More specifically, an optimization problem is formulated to evaluate the robustness of the WQSPSs, in which an evolutionary-based optimization approach coupled with an efficient data-archive method is used to solve this optimization problem. The framework is demonstrated on two real-world WDSs in China. The results show that: (1) the WQSPS's robustness can be highly dependent on the performance objectives considered, implying that an appropriate objective needs to be carefully selected for each case driven by practical needs, (2) the WDS's demand and configuration changes can have a significant influence on the WQSPS's robustness, in which the solution with more sensors in or close to the affected area is likely to better cope with these system changes, and (3) the proposed framework enables critical sensors to be identified, which can then be targeted for prioritizing maintenance actions.

@en

The Water Informatics in Science and Engineering Centre for Doctoral Training (WISE CDT) offers a postgraduate programme that fosters enhanced levels of innovation and collaboration by training a cohort of engineers and scientists at the boundary of water informatics, science and engineering. The WISE CDT was established in 2014 with funding from the UK Engineering and Physical Sciences Research Council (EPSRC) amongst the universities of Bath, Bristol, Cardiff and Exeter. The WISE CDT will ultimately graduate over 80 PhD candidates trained in a non-traditional 4-year UK doctoral programme that integrates teaching and research elements in close collaboration with a range of industrial partners. WISE focuses on cohort-based education and equips the PhD candidates with a wide range of skills developed through workshops and other activities to maximise candidate abilities and experiences. We discuss the need for, the structure and results of the WISE CDT, which has been ongoing from 2013-2022 (final year of graduation). We conclude with lessons learned and an outlook for PhD training, based on our experience with this programme.@en

Hydraulic modeling of a foul sewer system (FSS) enables a better understanding of the behavior of the system and its effective management. However, there is generally a lack of sufficient field measurement data for FSS model development due to the low number of in-situ sensors for data collection. To this end, this study proposes a new method to develop FSS models based on geotagged information and water consumption data from smart water meters that are readily available. Within the proposed method, each sewer manhole is firstly associated with a particular population whose size is estimated from geotagged data. Subsequently, a two-stage optimization framework is developed to identify daily time-series inflows for each manhole based on physical connections between manholes and population as well as sewer sensor observations. Finally, a new uncertainty analysis method is developed by mapping the probability distributions of water consumption captured by smart meters to the stochastic variations of wastewater discharges. Two real-world FSSs are used to demonstrate the effectiveness of the proposed method. Results show that the proposed method can significantly outperform the traditional FSS model development approach in accurately simulating the values and uncertainty ranges of FSS hydraulic variables (manhole water depths and sewer flows). The proposed method is promising due to the easy availability of geotagged information as well as water consumption data from smart water meters in near future.

@en

Urban sewer networks (SNs) are increasingly facing water quality issues as a result of many challenges, such as population growth, urbanization and climate change. A promising way to addressing these issues is by developing and using water quality models. Many of these models have been developed in recent years to facilitate the management of SNs. Given the proliferation of different water quality models and the promise they have shown, it is timely to assess the state-of-the-art in this field, to identify potential challenges and suggest future research directions. In this review, model types, modeled quality parameters, modeling purpose, data availability, type of case studies and model performance evaluation are critically analyzed and discussed based on a review of 110 papers published between 2010 and 2019. The review identified that applications of empirical and kinetic models dominate those of data-driven models for addressing water quality issues. The majority of models are developed for prediction and process understanding using experimental or field sampled data. While many models have been applied to real problems, the corresponding prediction accuracies are overall moderate or, in some cases, low, especially when dealing with larger SNs. The review also identified the most common issues associated with water quality modeling of SNs and based on these proposed several future research directions. These include the identification of appropriate data resolutions for the development of different SN models, the need and opportunity to develop hybrid SN models and the improvement of SN model transferability.

@en

Real-time hydraulic modelling can be used to address a wide range of issues in a foul sewer system and hence can help improve its daily operation and maintenance. However, the current bottleneck within real-time FSS modelling is the lack of spatio-temporal inflow data. To address the problem, this paper proposes a new method to develop real-time FSS models driven by water consumption data from associated water distribution systems (WDSs) as they often have a proportionally larger number of sensors. Within the proposed method, the relationship between FSS manholes and WDS water consumption nodes are determined based on their underlying physical connections. An optimization approach is subsequently proposed to identify the transfer factor k between nodal water consumption and FSS manhole inflows based on historical observations. These identified k values combined with the acquired real-time nodal water consumption data drive the FSS real-time modelling. The proposed method is applied to two real FSSs. The results obtained show that it can produce simulated sewer flows and manhole water depths matching well with observations at the monitoring locations. The proposed method achieved high R², NSE and KGE (Kling-Gupta efficiency) values of 0.99, 0.88 and 0.92 respectively. It is anticipated that real-time models developed by the proposed method can be used for improved FSS management and operation.

@en

Water distribution networks (WDNs) are vital parts of the urban infrastructure, and their construction, operation, and maintenance incur major investments. Therefore, many different approaches for optimizing WDNs exist. However, when it comes to large real WDNs, computational time becomes a significant factor, as the possible number of potential solutions grows exponentially. This paper discusses a highly efficient approach for Pareto-optimal design of WDNs based on complex network analysis (CNA). A real WDN with about 4,000 pipes (decision variables) was optimized first using a straightforward evolutionary algorithm approach with two objectives being cost minimization and resilience maximization. By systematically investigating topological features of the obtained Pareto-optimal solutions, insights into optimal networks are generated and a new design approach based on CNA is developed, which outperforms the results of the evolutionary algorithm. The proposed CNA approach is then successfully used to optimize a WDN with the same objectives where the evolutionary algorithm approach is computationally infeasible (semi-real case study with 157,040 decision variables).

@en

This paper proposes a multistage method for burst leak localization through valve operations (VOs) and smart demand metering in district meter areas (DMAs) of water distribution systems (WDSs). Each stage includes partitioning of the DMA into two subregions using VOs and identification of potentially leaking pipes within the subregions through water balance analysis based on smart demand meters. Such a process is performed repeatedly (multiple stages) to narrow down the spatial range for pinpointing leak locations. To improve efficiency, a bisection optimization problem is formulated to localize the minimum leak areas using the lowest number of VOs, which is solved by a graph theory-based method. The utility of the proposed method is demonstrated using two DMAs (DMA1 and DMA2) of a real WDS with different topological properties. Results show that the proposed method can efficiently localize artificial burst leaks in DMA1 within 7–15% of the total pipe length, implying that the proposed method is theoretically effective in localizing pipe burst leaks. The real application to DMA2 has identified two leak regions with 2.3 and 4.2 km of pipe length (around 3–6% of the entire DMA2) using 18 VOs. These two burst leaks have been subsequently confirmed and pinpointed using listening rods by practitioners of the local water utility. These results indicate that the proposed multistage method is effective and efficient for burst leak localization, which can be promising for wide practical applications due to rapid developments of smart WDSs (e.g., smart demand meters or control valves).

@en

Water quality sensors are often spatially distributed in water distribution systems (WDSs) to detect contamination events and monitor quality parameters (e.g., chlorine residual levels), thereby ensuring safety of a WDS. The performance of a water quality sensor placement strategy (WQSPS) is not only affected by sensor spatial deployment that has been extensively analyzed in literature, but also by possible sensor failures that have been rarely explored so far. However, enumerating all possible sensor failure scenarios is computationally infeasible for a WQSPS with a large number of sensors. To this end, this paper proposes an evolutionary algorithm (EA) based method to systematically and efficiently investigate the WQSPS′ global resilience considering all likely sensor failures. First, new metrics are developed in the proposed method to assess the global resilience of a WQSPS. This is followed by a proposal of an efficient optimization approach based on an EA to identify the values of global resilience metrics. Finally, the sensors within the WQSPS are ranked to identify their relative importance in maintaining the WQSPS's detection performance. Two real-world WDSs with four WQSPSs for each case study are used to demonstrate the utility of the proposed method. Results show that: (i) compared to the traditional global resilience analysis method, the proposed EA-based approach identifies improved values of global resilience metrics, (ii) the WQSPSs that deploy sensors close to large demand users are overall more resilient in handling sensor failures relative to other design solutions, thus offering important insight to facilitate the selection of WQSPSs, and (iii) sensor rankings based on the global resilience can identify those sensors whose failure would significantly reduce the WQSPS's performance thereby providing guidance to enable effective water quality sensor management and maintenance.

@en

The optimization of water networks supports the decision-making process by identifying the optimal trade-off between costs and performance (e.g., resilience and leakage). A major challenge in the domain of water distribution systems (WDSs) is the network (re)design. While the complex nature of WDS has already been explored with complex network analysis (CNA), literature is still lacking a CNA of optimal water networks. Based on a systematic CNA of Pareto-optimal solutions of different WDSs, several graph characteristics are identified, and a newly developed CNA design approach for WDSs is proposed. The results show that obtained designs are comparable with results found by evolutionary optimization, but the CNA approach is applicable for large networks (e.g., 150,000 pipes) with a substantially reduced computational effort (runtime reduction up to 5 orders of magnitude).

@en