Urban drainage models (UDMs) are often used to manage urban flooding. However, these models generally involve many parameters to represent the underlying complex hydrodynamic processes. This results in significant challenges to achieving effective and robust model calibration especially with frequently limited observations, leading to unreliable model predictions. This paper makes the first attempt at UDM calibration using the Bayesian-based Ensemble Smoother (ES) method. Three ES variants are considered, that is, the primary ES, the versions with multiple data assimilation (ES-MDA) and iterative local update (ES-ILU). Two synthetic cases and one real-world application with up to 5,236 calibration parameters are tested. Results obtained show that: (a) both ES-MDA and ES-ILU can produce effective model calibration with ES-ILU outperforming ES-MDA in terms of both accuracy and uncertainty while ES exhibits limited performance; (b) for the real-world case, both the ES-MDA and ES-ILU methods provide better calibration results than the best-known solution manually obtained, (c) a minimum number of observations are required to enable an overall accurate model calibration (e.g., four and ten more monitoring sites are needed in the two synthetic cases); and (d) the model calibrated using an intense rainfall event is generally robust to make reliable predictions across different rainfall events while the model calibrated using less intense rainfall event does not perform well for more intense rainfall events. It was also found that ubiquitous parameter equifinality significantly hinders unique parameter identification even when overall accurate state estimates are obtained. This should be clearly understood in practical applications.

Most of the contamination source localization methods for water distribution systems (WDSs) assume the availability of accurate water quality models and multi-parameter online sensors, which are often out of reach of many water utilities. To address this, a novel manual grab-sampling method (MGSM) is developed to effectively and efficiently locate continuous contamination sources in a WDS using a dynamic and cyclical sampling strategy. The grab samples are collected at a pre-specified number of hydrants by the corresponding teams followed by laboratory tests. The MGSM optimizes the sampling plan at each cycle by making the probability of contamination source(s) in each sub-network as equal as possible, where sub-networks are determined by the selected hydrants and current flow pipe directions. The CS's size is reduced at each cycle by exploiting sample testing results obtained in the previous cycle until there are no further hydrants to sample from. Two real-world WDSs are used to demonstrate the effectiveness of the proposed MGSM. The results obtained show that the MGSM can significantly reduce the spatial range of the CS (to about 5% of the entire WDS) for a range of scenarios including multiple contamination sources and pipe flow direction changes. We found that an optimal number of sampling teams exists for a given WDS, representing a balanced trade-off between detection efficiency and sampling/testing budgets. Due to its relative simplicity, the proposed MGSM can be used in engineering practice straightaway and it represents a viable alternative to the methods associated with water quality models and sensors.

Improving the resilience of water distribution systems (WDSs) to handle natural disasters (e.g., earthquakes) is a critical step toward sustainable urban water management. This requires the water utility to be able to respond quickly to such disaster events, and in an organized manner, to prioritize the use of available resources to restore service rapidly while minimizing the negative impacts. Many methods have been developed to evaluate the WDS resilience, but few efforts are made so far to improve the resilience of a postdisaster WDS through identifying optimal sequencing of recovery actions. To address this gap, the authors propose a new dynamic optimization framework in this study in which the resilience of a postdisaster WDS is evaluated using six different metrics. A tailored genetic algorithm is developed to solve the complex optimization problem driven by these metrics. The proposed framework is demonstrated using a real-world WDS with 6,064 pipes. Results obtained show that the proposed framework successfully identifies near-optimal sequencing of recovery actions for this complex WDS. The gained insights, conditional on the specific attributes of the case study, include the following: (1) the near-optimal sequencing of a recovery strategy heavily depends on the damage properties of the WDS; (2) replacements of damaged elements tend to be scheduled at the intermediate-late stages of the recovery process due to their long operation time; and (3) interventions to damaged pipe elements near critical facilities (e.g., hospitals) should not be necessarily the first priority to recover due to complex hydraulic interactions within the WDS.

This paper proposes a multistage method for burst leak localization through valve operations (VOs) and smart demand metering in district meter areas (DMAs) of water distribution systems (WDSs). Each stage includes partitioning of the DMA into two subregions using VOs and identification of potentially leaking pipes within the subregions through water balance analysis based on smart demand meters. Such a process is performed repeatedly (multiple stages) to narrow down the spatial range for pinpointing leak locations. To improve efficiency, a bisection optimization problem is formulated to localize the minimum leak areas using the lowest number of VOs, which is solved by a graph theory-based method. The utility of the proposed method is demonstrated using two DMAs (DMA1 and DMA2) of a real WDS with different topological properties. Results show that the proposed method can efficiently localize artificial burst leaks in DMA1 within 7–15% of the total pipe length, implying that the proposed method is theoretically effective in localizing pipe burst leaks. The real application to DMA2 has identified two leak regions with 2.3 and 4.2 km of pipe length (around 3–6% of the entire DMA2) using 18 VOs. These two burst leaks have been subsequently confirmed and pinpointed using listening rods by practitioners of the local water utility. These results indicate that the proposed multistage method is effective and efficient for burst leak localization, which can be promising for wide practical applications due to rapid developments of smart WDSs (e.g., smart demand meters or control valves).