A novel test setup called the asymmetric shock tube for experiments on nonideal rarefaction waves (ASTER) has been commissioned at Delft University of Technology. The ASTER, which works according to the principle of Ludwieg tubes, is designed to generate and measure the speed of small and finite amplitude waves propagating in the dense vapors of fluids formed by complex organic molecules, therefore in the nonideal compressible fluid dynamics regime. The ultimate goal of the associated research is to prove the existence of nonclassical gasdynamics. The setup consists of a high-pressure charge tube and a vacuum tank separated by a glass disk equipped with a breaking mechanism for rarefaction waves experiments. When the glass disk is broken, an expansion wave propagates into the tube in the direction opposite to the fluid flow. The propagation speed of this wave is measured using a time-of-flight method with the help of four fast-response pressure sensors placed equidistantly in the middle of the tube. The charge tube can withstand pressures and temperatures of up to 15 bar and 400∘C. Preliminary rarefaction experiments were successfully conducted using dodecamethylcyclohexasiloxane, D₆, as the working fluid and at pressures and temperatures of up to 9.4 bar and 372∘C, respectively. The results of an experiment featuring the initial state for which a theoretical model predicts the nonclassical acceleration of rarefaction waves show that the propagation is qualitatively different from that put into evidence by experiments for which the propagation is classic. Upcoming setup improvements and experimental campaigns are planned with the objective of experimentally verifying the existence of nonclassical gasdynamics. Graphical abstract: (Figure presented.)

@en

Micro-pin-fin evaporators are a promising alternative to multi-microchannel heat sinks for two-phase cooling of high power-density devices. Within pin-fin evaporators, the refrigerant flows through arrays of obstacles in cross-flow and is not restricted by the walls of a channel. The dynamics of bubbles generated upon flow boiling and the associated heat transfer mechanisms are expected to be substantially different from those pertinent to microchannels; however, the fundamental aspects of two-phase flows evolving through micro-pin-fin arrays are still little understood. This article presents a systematic analysis of flow boiling within a micro-pin-fin evaporator, encompassing bubble, thin-film dynamics and heat transfer. The flow is studied by means of numerical simulations, performed using a customised boiling solver in OpenFOAM v2106, which adopts the built-in geometric Volume of Fluid method to capture the liquid–vapour interface dynamics. The numerical model of the evaporator includes in-line arrays of pin-fins of diameter of 50μm and height of 100μm, streamwise pitch of 91.7μm and cross-stream pitch of 150μm. The fluid utilised is refrigerant R236fa at a saturation temperature of 30 °C. The range of operating conditions simulated includes values of mass flux G=500–2000kg/(m²s), heat flux q=200kW/m², and inlet subcooling ΔT_sub=0–5K. This study shows that bubbles nucleated in a pin-fin evaporator tend to travel along the channels formed in between the pin-fin lines. Bubbles grow due to liquid evaporation and elongate in the direction of the flow, leaving thin liquid films that partially cover the pin-fins surface. The main contributions to heat transfer arise from the evaporation of this thin liquid film and from a cross-stream convective motion induced by the bubbles in the gap between the cylinders, which displace the hot fluid otherwise stagnant in the cylinders wakes. When the mass flow rate is increased, bubbles depart earlier from the nucleation sites and grow more slowly, which results in a reduction of the two-phase heat transfer. Higher inlet subcooling yields lower two-phase heat transfer coefficients because condensation becomes important when bubbles depart from the hot pin-fin surfaces and reach highly subcooled regions, thus reducing the two-phase heat transfer.

@en

The present study investigates pool boiling heat transfer of Novec 649 on structured copper surfaces. Structures with varying height and spacing, in the range of 400–1200 µm, were machined on the boiling surface using electro-discharge machining (EDM). Pool boiling experiments have been performed to estimate the heat transfer performance of pin-fin structures using Novec 649 as the cooling fluid. The heat transfer coefficient (HTC) and the critical heat flux (CHF) limit of the structured surfaces have been estimated and compared to those of the unstructured ones, both in the horizontal and vertical orientation. In this work, the effects of pin fin heights and spacing, with dimensions similar to the capillary length scale, on the heat transfer coefficient and critical heat flux limit are examined. The experimental results demonstrate that adding pin-fin structures significantly enhances boiling heat transfer. Specifically, the HTC and CHF increases by factors of up to 10 and 2.8, respectively, compared to the smooth surface. This enhancement is primarily driven by the wetted area increase due to the pin-fin structures. The HTC per unit wetted area was found to be independent of geometry during the early stage of nucleate boiling and only exhibited a weak dependence on geometry in the later stages. Notably, the HTC per unit wetted area deteriorates when the pin fin spacing is less than the capillary length scale.@en

Recent advancements in laser and imaging systems, as well as in computational processing capabilities, have made quantitative optical imaging, which is often combined with laser illumination, highly adaptable, robust and reliable. Laser-based diagnostic techniques, such as planar laser-induced fluorescence (PLIF), offer the possibility of simultaneous spatiotemporally resolved measurements of temperature fields in the liquid phase at boiling conditions. In this paper, we examine the applicability of two-colour PLIF (2cPLIF), where the ratio between individual fluorescent emissions from uniformly dispersed dyes is used to take temperature measurements in the liquid phase in the presence of moving vapour-liquid interfaces typical of boiling flow. The implementation of 2cPLIF necessitates uniformity in the concentration of different dyes across the flow field. However, in the case of a multiphase flow such as boiling, thermophoresis can lead to inhomogeneous dye distributions. To overcome this challenge, a single-dye multispectral planar laser-induced fluorescence (SDMS-PLIF) method has been developed, which employs fluorescent emissions in different spectral bands of the same dye (Nile Red). The spectral characteristics of Nile Red were measured using a spectrometer to identify its temperature-sensitive bands over a wide range of dye concentrations, from 0.3 to 30 mg/L. Following this, we demonstrate the measurement capabilities of SDMS-PLIF thermography as applied to a boiling flow in a miniaturised vertical square channel, gaining insight into the thermohydrodynamic interactions between vapour bubbles and a heated wall.

@en