A novel test setup called the asymmetric shock tube for experiments on nonideal rarefaction waves (ASTER) has been commissioned at Delft University of Technology. The ASTER, which works according to the principle of Ludwieg tubes, is designed to generate and measure the speed of small and finite amplitude waves propagating in the dense vapors of fluids formed by complex organic molecules, therefore in the nonideal compressible fluid dynamics regime. The ultimate goal of the associated research is to prove the existence of nonclassical gasdynamics. The setup consists of a high-pressure charge tube and a vacuum tank separated by a glass disk equipped with a breaking mechanism for rarefaction waves experiments. When the glass disk is broken, an expansion wave propagates into the tube in the direction opposite to the fluid flow. The propagation speed of this wave is measured using a time-of-flight method with the help of four fast-response pressure sensors placed equidistantly in the middle of the tube. The charge tube can withstand pressures and temperatures of up to 15 bar and 400∘C. Preliminary rarefaction experiments were successfully conducted using dodecamethylcyclohexasiloxane, D₆, as the working fluid and at pressures and temperatures of up to 9.4 bar and 372∘C, respectively. The results of an experiment featuring the initial state for which a theoretical model predicts the nonclassical acceleration of rarefaction waves show that the propagation is qualitatively different from that put into evidence by experiments for which the propagation is classic. Upcoming setup improvements and experimental campaigns are planned with the objective of experimentally verifying the existence of nonclassical gasdynamics. Graphical abstract: (Figure presented.)

@en

The blade solidity, namely the blade chordtopitch ratio, largely affects the fluiddynamic performance of turbomachinery. For turbomachines operating with air or steam, the optimal value of the solidity which maximizes the efficiency is estimated with empirical correlations such as the ones proposed by Zweifel (1945) and Traupel (1966). However, if the turbomachine operates with unconventional fluids, the accuracy of these correlations becomes questionable. Examples of such working fluids are the nonideal (dense) vapors of organic compounds (e.g., hydrocarbons, siloxanes) used to operate organic Rankine cycle (ORC) power systems. This study investigates the effect of both the working fluid and the flow compressibility on the optimum pitchtochord ratio of turbine stages. A first principle model for the profile losses is developed for this purpose. Charts providing the optimal pitchtochord ratio for unconventional turbine stages are then provided. Numerical simulations of the flow over a turbine stator cascade have been conducted to validate the model results and evaluate the influence of both working fluid, flow compressibility, and solidity value on the loss breakdown. The results show that the optimal solidity of turbine cascades value significantly increases with the flow compressibility. Therefore, models providing the optimal solidity based on the estimate of passage loss only are not suited for unconventional turbines. @en

Waste heat recovery (WHR) from aero engines via compact organic Rankine cycle (ORC) units may increase the fuel efficiency of air transportation. Heat exchangers are arguably the key components of ORC systems for aeronautical applications and their design must be optimized to guarantee the best trade-off between fluid pressure drop, weight, and induced aircraft drag. At present, no heat exchanger design guidelines are available for waste heat recovery systems aboard aircraft. This study, thus, contributes to defining a proper design methodology for ORC systems of such applications. The chosen
test case is a supercritical ORC system with cyclopentane as the working fluid, which recovers waste heat from the auxiliary power unit of an aircraft. The exhaust gas temperature and mass flow rate of the power unit are known and kept constant in the analysis, and so are the ambient conditions, which define the cold sink of the ORC turbogenerator. Three design strategies targeting the minimum mass and maximum net power output of the ORC unit have been assessed. In the first one, the multi-objective optimization is performed by prescribing a priori the geometry and frontal area of the heat exchangers.
Thus, only the cycle parameters are optimized. The second method tackles, instead, the simultaneous optimization of the geometric parameters of the condenser and the cycle parameters. It was found that the integrated design allows for system mass reduction by 10 - 12% for a given ORC power output, highlighting the importance of performing the simultaneous optimization of the thermodynamic process and the heat exchanger geometry. Finally, the third method addresses the same optimal design problem by leveraging a reduced-order model of the condenser to predict the optimal design space of this component. The generated Pareto front obtained with this method is very similar to that found by optimizing simultaneously the complete condenser geometry and the cycle parameters. The mean deviation is about 2%. With just one heat exchanger surrogate model, the Pareto front was generated in one-fourth of the computational time. This is due to the lower number of optimization variables and the faster objective function evaluation.@en

The gas dynamics of single-phase nonreacting fluids whose thermodynamic states are close to vapor-liquid saturation, close to the vapor-liquid critical point, or in supercritical conditions differs quantitatively and qualitatively from the textbook gas dynamics of dilute, ideal gases. Due to nonideal fluid thermodynamic properties, unconventional gas dynamic effects are possible, including nonclassical rarefaction shock waves and the nonmonotonic variation of the Mach number along steady isentropic expansions. This review provides a comprehensive theoretical framework of the fundamentals of nonideal compressible fluid dynamics (NICFD). The relation between nonideal gas dynamics and the complexity of the fluid molecules is clarified. The theoretical, numerical, and experimental tools currently employed to investigate NICFD flows and related applications are reviewed, followed by an overview of industrial processes involving NICFD, ranging from organic Rankine and supercritical CO2 cycle power systems to supercritical processes. The future challenges facing researchers in the field are briefly outlined.@en

In evaporators, the distribution of the liquid and vapor phases among the channels is a convoluted problem, depending on a wide range of parameters. However, maldistribution causes important losses of performance. Due to their complexity, the accurate modeling of such two-phase flows is difficult to handle. Hence, experimental studies are still of great importance to help the understanding of maldistribution behaviors inside evaporators. Most of the experimental investigations of two-phase flow distribution are measuring the liquid and vapor quantities in the channels through a phase separation process, increasing the test duration and complexity. As a consequence, the number of parameters investigated is usually limited. Therefore, a new inline instrumentation method would allow for a more complete study by simplifying the measurement process. In the present work, an isothermal air/water mixture was used as fluid. The distribution of the two phases in eight channels of 10-mm I.D. connected to a simplified header was investigated. The inlet mass flow rates considered ranged from 0 to 0.025 kg/s for the water, and from 0 to 0.022 kg/s for the air. Consequently, qualities x up to 0.7 and void fractions ® up to 0.9 were reached. All the tests were carried at a pressure condition of 7 bar to reach a liquid to vapor density ratio similar to what is encountered for traditional refrigerant. Finally, to allow a continuous measurement process, the mass flow rates in each of the 10-mm I.D. channel were measured using a flowmeter calibrated on a separate line. Since no void fraction meter was coupled, a new iterative methodology, based on the Venturi pressure drops measurement solely, was developed and is proposed here. It proved to successfully predict the vapor and liquid phase flow rates in each channel.

@en

The use of mixtures as working fluids of organic Rankine cycle (ORC) waste heat recovery (WHR) power plants has been proposed in the past to improve the matching between the temperature profile of the hot and the cold streams of condensers and evaporators, thus to possibly increase the energy conversion efficiency of the system. The goal of this study is to assess the benefits in terms of efficiency, environmental (GWP) and operational safety (flammability) that can be obtained by selecting optimal binary mixtures as working fluids of air-cooled ORC bottoming power plants of medium-capacity industrial gas turbines. Furthermore, two thermodynamic cycle configurations are analyzed, namely the simple recuperated cycle and the so-called split-cycle configurations. The benchmark case is a combined cycle power plant formed by an industrial gas turbine and an air-cooled recuperated ORC power unit with cyclopentane as the working fluid. The results of this study indicate that binary mixtures provide the designer with a wider choice of optimal working fluids, however, in the case of the recuperated-cycle configuration, no improvement in terms of combined cycle efficiency over the benchmark case can be achieved. The split-cycle configuration leads to an increase of combined cycle efficiency of the order of 1.5%, both in case of pure and blended working fluids. Furthermore, for this cycle configuration the use of Novec 649 as working fluid is advantageous because it is environmentally and operationally safe, and it does not involve any penalty in terms of combined cycle efficiency if compared to the benchmark case. Additionally, the use of this fluid would lead to a more compact turbine, as the corresponding thermodynamic cycle would determine a turbine volume flow ratio that is half of the value of the benchmark case and a specific enthalpy difference over the expansion that is one fifth.

@en

The aircraft Environmental Control System (ECS) is the primary consumer of non-propulsive power at cruise conditions, hence, its performance optimization is crucial for the reduction of specific fuel consumption. A novel integrated system design optimization method is presented: thermodynamic cycle, component sizing and working fluid are taken into account simultaneously. This method was applied to the ECS of large rotorcraft based on a Vapour Compression Cycle system electrically driven by a high-speed centrifugal compressor. Steady-state and lumped parameter system component models have been developed using the Modelica acausal modelling language. The optimization design framework consists of an in-house code, featuring a Python-Modelica interface. The study case refers to a critical operating condition: the helicopter is on the ground during a hot and humid day. The working fluid is R-134a. The multi-objective optimization targets the maximization of the system efficiency and the minimization of system weight. The results show that more efficient systems can be designed only with heavier components. The design feasibility of high-speed centrifugal compressors is demonstrated. The advantage of an integrated system design optimization framework for complex energy systems is proved, allowing for the analysis of the impact of both component design and working fluid on system performance.

@en

Compressible flows of fluids whose thermophysical properties are related by complex equations are quantitatively and can be qualitatively different from high-speed flows of ideal gases. Nonideal compressible fluid dynamics (NICFD) is concerned with these fluid flows, which are relevant in many processes and power and propulsion systems. Typically, NICFD effects occur if the fluid is an organic compound and its vapor state is close to the vapor–liquid critical point, at high-reduced temperature and pressure (even supercritical). Current design and analysis of devices operating in the nonideal compressible regime demand for validated simulation software, characterized in terms of uncertainty. Moreover, experiments are needed to further validate related theory. Experimental data are limited as generating and measuring these flows is challenging given their high pressure or temperature or both. In addition, flows of organic compounds can be flammable, can thermally decompose, and sealing may demand for special materials. Recently, more research has been devoted to the measurement of these flows using both intrusive and less intrusive techniques relying on optical access and lasers. The transparency and refractive properties of these dense vapors pose additional problems. The ORCHID (organic Rankine cycle hybrid integrated device) at the Aerospace Propulsion and Power Laboratory of Delft University of Technology is a closed-loop facility, used to generate a continuous nonideal supersonic flow of siloxane MM with the vapor at 4bar and 220 °C at the inlet of the test section. Within this work, we have employed particle image velocimetry for the first time to obtain the velocity field in a de Laval nozzle in such flows. Measured velocity fields (expanded uncertainty within 1.1% of the maximum velocity) have been compared with those resulting from a CFD simulation. The comparison between experimental and simulated data is satisfactory, with deviation ranging from 0.1 to 10 % from the throat to the outlet, respectively. This discrepancy is attributed to hardware limitations, which will be overcome in the future experiments. The feasibility of PIV with uncontrolled but fixed seeding density to measure high-speed vapors of organic vapors has been demonstrated, and future experimental campaigns will target flows for which nonideal effects are more pronounced, other paradigmatic configurations, and improvements to the measurement techniques.

@en

This research evaluates Laser Powder Directed Energy Deposition (LP-DED) for producing fine feature internal microchannels. This study is focused on enhancing and characterising the surfaces of microchannels produced using techniques such as abrasive flow machining, chemical milling, chemical mechanical polishing, electrochemical machining, and thermal energy method to modify internal surfaces of microchannels made from NASA HR-1 Fe-Ni-Cr alloy. Flow testing for discharge coefficient measurement is conducted on processed microchannel samples, followed by characterisation through optical microscopy, Scanning Electron Microscopy (SEM), and Computed Tomography. Findings reveal variations in surfaces due to powder adherence, melt pool undulations, and polishing mechanisms. The study emphasises the significance of removing material equivalent to the mean powder diameter to reduce surface roughness and impact the discharge coefficient. The research proposes a ratio for planarising roughness and waviness peak height and density, offering insights for tailored surface adjustments in specific applications requiring reduced flow resistance. Highlights Internal microchannels with thin-walls were fabricated using the laser powder directed energy deposition process. Various surface enhancements and polishing processes were developed to modify the surface texture of the LP-DED channels. Flow testing was conducted to determine the discharge coefficient. Post-test characterisation was completed to obtain cross sectional area, perimeter, surface texture, and general surface condition to analyse results. Ratio of roughness and waviness peak and density (Spk/Spd and Wp/WPc) is proposed as a relevant surface characterisation parameter. Tailored surface modifications for specific end-use applications.

@en

This paper presents a preliminary study about a combined-cycle engine based on a turboshaft engine and an organic-Rankine-cycle (ORC) bottoming unit to be used onboard an aircraft with a turboelectric propulsion system. The aim is to analyse whether benefits with respect to mission fuel consumption can be derived by employing such a combined-cycle
engine when compared to a simple-cycle turboshaft engine. For this purpose, a multidisciplinary optimization framework is developed, incorporating models for the engine, ORC system, ORC turbine, heat exchangers, and mission analysis. This framework is coupled with an optimizer to identify the optimal combined-cycle engine design for minimum mission fuel consumption. The results suggest that fuel savings of around 1.5% are possible with the optimized system if compared to the aircraft employing turboshaft engines. Heat exchanger volume is identified as the most constraining parameter when it comes to combined-cycle performance. The analysis of the results suggests as aspects which might lead to further improvements the evaluation of other ORC architectures, working fluids and heat exchanger topologies.@en

The Environmental Control System (ECS) of passenger aircraft is the main consumer of non-propulsive power aboard. A computationally efficient and accurate thermal model of the fuselage is needed for future sustainable aircraft to address ECS preliminary sizing and control design, as the ECS should be re-designed to exploit possible synergies with other thermal management systems on board. Differently from previous works, the present aircraft thermal model is extensively documented and released open-source. Moreover, it is completely based on first principles and the acausal modeling paradigm. It results that the model is scalable, easily extendable, and allows for the estimation of the aircraft thermal loads given limited information about its configuration and flight mission. The predictive capabilities of the model have been assessed by comparing the thermodynamic state estimated at the pack discharge for three ECS operating points of an Airbus A320 with data provided by the manufacturer. The maximum deviation is limited to 2.4 K and 4.5 kPa. The validated thermal model has been used to compute the operating envelope of the A320 ECS, showing that the air supply requirements vary substantially with ambient conditions and flight phases. This calls for a multi-point design strategy when assessing novel ECS configurations.

@en

This paper describes the design, functioning, and preliminary experiments in the Asymmetric Shock Tube for Experiments on Rarefaction Waves (ASTER), a Ludwieg-type shock tube designed and realised to measure waves propagating in dense vapour flows of organic fluids. The setup is designed to operate at pressures and temperatures of up to 15 bar and 400^∘ C. The high and low-pressure sections of the tube are separated by a glass-disk barrier to ensure quasi-instantaneous opening. When the glass disk is broken, a rarefaction wave propagates into the tube. The wave speed is measured using a time-of-flight method with the help of four pressure transducers placed at known distances from each other. Leakage rates of 2.2 × 10^{- 4} mbar · l · s^{- 1} at vacuum and 5 × 10^{- 4} mbar · l · s^{- 1} at superatmospheric pressures were measured, which is considered sufficient for the conceived experiments. Preliminary rarefaction experiments in the dense vapours of dodecamethylcyclohexasiloxane, D₆, were successfully performed at various thermodynamic conditions. Also, a method for the estimation of sound speeds from the pressure sensor recordings is proposed. Results are found to be within 2.5% of the values predicted by the state-of-the-art thermodynamic model for D₆.

@en

This paper describes an experiment conducted within the nozzle test section of the Organic Rankine Cycle Hybrid Integrated Device (ORCHID) aimed at providing accurate data for the validation of NICFD flow solvers [5]. A supersonic flow of the dense vapor siloxane MM established in the nozzle of the setup was characterized by means of the schlieren technique and by pressure taps along the nozzle profile. The nozzle inlet conditions corresponded to a stagnation temperature and pressure of T0=253∘C and P0=18.36bara. At these inlet conditions, the compressibility factor of the fluid is Z₀= 0.58. The nozzle backpressure was equal to Pb=2.2bara. The experimental data-set includes: 1) the average mid-plane local Mach number, which was derived from the schlieren images by estimating the angle of the Mach waves originating from the roughness of the upper and lower nozzle surfaces, 2) the angle of a shock wave generated by a 5^∘ wedge placed at the nozzle exit, also detectable in the schlieren images, and 3) the static pressure distribution along the flow expansion acquired with a Scanivalve DSA3218 pressure scanner device. The Mach number at the nozzle exit estimated based on the schlieren images is M= 1.95 ± 0.05, very close to the expected value of M= 2 according to the design conditions of the experiment. The static pressure measurements have a maximum absolute uncertainty amounting to ± 1.80 kPa in the initial stages of the expansion. This information was used to assess the capability of the open-source SU2 flow solver in evaluating the NICFD effects in a supersonic flow of MM when the fluid thermodynamic properties are modeled with a cubic equation of state. For this purpose, two-dimensional Euler simulations were carried out with SU2 for the operating conditions achieved in the experiment. The numerical results are in good agreement with the experimental data. The largest deviation between the simulation and experiment is observed in the nozzle uniform region, where two dips in the Mach number occur due to a slight local decrease in flow velocity owing to two weak shock waves. The shock wave generated by the wedge located at the nozzle outlet propagates with two different angles, namely, β_above= 37. 6^∘± 0.86, and β_below= 31. 6^∘± 0.64, due to the axial misalignment of the wedge with respect to the flow.

@en

Metal additive manufacturing (AM) is being used for mission-critical applications in both developmental and production components, driven by economic and technical benefits. Laser powder directed energy deposition (LP-DED) allows manufacturing of thin wall geometric features for various components at diameters larger than 2 m. The characterization of geometric capabilities and limitations is critical for establishing guidelines for end users of the technology. Within this study, several samples of enclosed vertical tracks were fabricated and characterized using LP-DED, with 1 mm-thick walls and varying inclination angles up to 45° using the NASA HR-1 alloy (Fe-Ni-Cr). The wall thickness, melt pool, and surface texture, inclusive of waviness and roughness, were evaluated and results presented. The experimental results indicate that the wall thickness increases exponentially above 30°. The surface texture was shown to be dependent on 1) excess powder adherence, 2) melt pool irregularities causing material droop, and 3) excess material. The experiment revealed that the mean roughness reduces with increasing wall angle for the downskin surface. The upskin roughness reaches a maximum peak at 20° and slowly reduces as powder adheres within the valleys. Both the downskin and upskin surface textures are dominated by irregular waviness generated by the melt pool.@en

Estimating the speed of sound for the dense vapor phase of D₆ (dodecamethylcyclohexasiloxane, C₁₂H₃₆O₆Si₆) is particularly relevant to the study of nonideal compressible fluid dynamics (NICFD), the gas dynamics of fluids whose properties depart significantly from those related by the ideal gas model. If molecular complexity is sufficiently large, dense vapor flows may exhibit so-called nonclassical gasdynamic effects, and D₆ is a candidate for experimental studies aimed at proving for the first time the existence of these exotic phenomena. More in general, speed of sound measurements in the dense vapor phase are important for NICFD applications: for example, complex organic compounds are employed as working fluids in organic Rankine cycle power plants and the correct prediction of the dense-vapor speed of sound is of paramount importance for the design of the supersonic turbines equipping these systems. This type of measurements is challenging and thus rare, especially in the case of complex organic molecules, given the high temperature at which they must be performed, close to the temperature at which the molecule thermally decomposes. Therefore, a new prismatic resonator (the OVAR, organic vapor acoustic resonator) has been conceived, designed, and realized. It is suitable for speed of sound measurements in the vapor phase of organic compounds at temperatures up to approximately 670 K and pressures up to about 1.5 MPa. The speed of sound of D₆ (97.4% pure) has been measured along eight isotherms between 555 and 645 K and from nearly saturated density to densities close to ideal gas conditions (compressibility factor Z ≈ 0.95). The estimated relative uncertainty of these sound speed measurements is 0.14%. In addition, corresponding density values have been obtained with an estimated uncertainty between 0.2 kg·m^-3 and 1.2 kg·m^-3

@en

The environmental control system (ECS) is the largest auxiliary power consumer, i.e, around 75% of non-propulsive power, among the aircraft subsystems. The adoption of a novel ECS architecture, based on an electrically-driven vapor compression cycle system, can enable a twofold increase of coefficient of performance (COP), as compared to the conventional air cycle machine (ACM). The core of this technology is a high-speed, miniature centrifugal compressor, consisting of two impellers mounted in back-to-back configuration, and running on gas bearings operating with refrigerant. The fluid dynamic design optimization of the twin-stage compressor, to be installed in the vapor compression cycle test rig under realization at Delft University of Technology, is documented in this paper. First, the scaling analysis for centrifugal compressor is extended to provide guidelines for the design of twin-stage machines. Then, a multi-objective conceptual design optimization is performed by resorting to an in-house reduced-order model (ROM), coupled to a genetic algorithm. The fluid dynamic performance and the structural integrity of the optimal design are assessed by means of a hybrid framework, encompassing CFD and ROMs, and by FEA. The results show that it is possible to design a twin-stage compressor for the target application, featuring an average efficiency higher than 70%, a maximum compression ratio exceeding 9, and an operating range of 0.27 at the design rotational speed, despite the detrimental effects of motor cooling and miniature size.

@en

The use of mixtures in place of pure fluids in Organic Rankine Cycle (ORC) power plants is proposed as a possible improvement in terms of efficiency, environmental benefit and safety of the system. In particular, zeotropic mixtures exhibit a temperature variation (or glide) during phase change, because the components have different boiling points. This temperature glide improves the temperature profile matching in the heat exchangers and could in turn increase the overall thermoeconomic efficiency of the power plant, especially if it is air cooled. Even though the solution is theoretically beneficial, its practical feasibility has still to be proven. To this scope, we developed an optimization algorithm that determines the optimal mixture composition and thermodynamic parameters of the cycle and performs the preliminary design of the air cooler of the power plant. As initial case study we chose a heat recovery application and ran single objective optimizations to select the binary mixture that maximizes the power plants thermodynamic efficiency. Initial results show that, when the ratio between the turbine and fan power is high and the maximum temperature is constrained by fluid stability considerations, mixtures with low or no glide are the most efficient. The optimization procedure will eventually be extended to include also the economic aspect and additional studies will be performed for the geothermal application, where mixtures are expected to be much more beneficial due to the lower temperature of the heat source. @en

The impact of size and working fluid on the efficiency, operating range, and axial thrust on bearings is examined for high-speed, oil-free centrifugal compressors. First, the development and validation of a reduced-order model based on scaling principles is documented. Then, the validated compressor model is used to generate design maps for stages operating with arbitrary fluid molecules, and characterized by different size. The results show that compressors operating with fluids made by heavy and complex molecules provide lower efficiency over the entire design space, if compared to their simple-molecule counterparts. However, compressors for complex-molecule fluids require lower rotational speed, and generate lower axial thrust on bearings, thus making them particularly suitable for small-scale applications. Furthermore, a decreasing value of the size parameter has a detrimental effect on the stage efficiency, as a result of manufacturing constraints. The results computed by the compressor model suggest that the efficiency penalty is more sensitive to variations of clearance gap than to surface finishing. Lastly, the reduced-order model has been used to perform a design exercise, i.e., the multi-objective optimization of the first compressor stage of the heat pump test rig being realized at Delft University of Technology. The key characteristics of the optimal compressor design has been compared to those derived from the design maps, to corroborate their validity. The optimal design has been extensively characterized by means of CFD, providing further evidence that efficient mini-compressors operating with organic fluids, and featuring pressure ratios up to five at off-design, are feasible.

@en

Heat exchangers for use in propulsion applications are very critical components because they must be efficient, compact and light and often operate with working fluids at extreme temperatures or pressures or both. Various components and systems use heat exchangers such as combustion chambers of gas turbines and internal combustion engines, fuel cells (air supply and thermal management), electric batteries (thermal management), evaporators and recuperators of waste-heat-to-power systems, and rocket engines. Even if the results are more generally applicable, the heat exchangers applications to which this study is more closely related are regeneratively cooled rocket nozzles and chambers, and repressurization systems for the launch vehicles. These components are often thin-walled and contain pressurized fluids, like propellants at cryogenic or elevated temperatures. Given that the environments that these propulsion components must endure are challenging, the manufacturing to meet these specifications often require long lead times due to specialty processes and unique tooling associated with the combined thin-wall integral channel and large-scale structures. Additive manufacturing (AM) offers programmatic advantages for reduction in processing time and cost in addition to various technical advantages, including the possibility to achieve enhanced hardware complexity targeted to superior performance, part consolidation, and the capability of processing of novel alloys. While AM is already being utilized for heat exchanger components in propulsion applications, almost all these AM components are made by means of Laser Powder Bed Fusion (L-PBF). L-PBF allows for fine features but is rather limited with respect to the overall size of the components that can be manufactured. Recent developments are maturing the Laser Powder Directed Energy Deposition (LP-DED) process which may be used, for example, to make integral channel thin-wall regeneratively-cooled rocket nozzles with diameters greater than 1 m. This paper highlights some integral channel heat exchanger demonstrator hardware applications of LP-DED, as well as the characterization of this process in combination with the use of the NASA HR-1 alloy. To properly utilize LP-DED for heat exchanger manufacturing, various aspects are being characterized such as geometry limitations, measurement of surface texture and geometric angled surfaces, surface enhancements for internal channels, and material evaluation. NASA HR-1 (Fe-Ni-Cr) is a high strength hydrogen resistant superalloy developed for use in aerospace applications, such as heat exchangers. Some aspects and considerations about the design of heat exchangers are summarized together with data relevant to LP-DED manufacturing in combination with the NASA HR-1 alloy. Microchannels were successful deposited down to 2.54 mm and 1 mm wall thickness, wall angles of 30°, both with high reproducibility. It was also found that the areal surface roughness is highly dependent on the size of the powder feedstock used for deposition. The characterization of these LP-DED features is critical for fluid flow and heat transfer predictions as it can be exploited to enhance heat transfer at the cost of increased pressure drop. @en

In this work we examine the flow deviation and its relationship to critical choking, i.e., choking of the meridional component of velocity, in transonic turbine cascades operating with non-ideal compressible flows. To this purpose, a generalized expression of the corrected flow per unit area as a function of both the thermodynamic state and the molecular complexity of the working fluid, the Mach number, and the amount of swirl is derived. The trends of the corrected flow with respect to these quantities are used to infer physical insights on the flow deviation and on the operability of transonic turbine cascades in off-design conditions. Moreover, reduced-order models for the estimation of the flow deviation and the preliminary assessment of the losses have been developed and validated against the results of CFD simulations performed on a representative transonic turbine stator. Results suggest that flows of dense organic vapors exhibit larger deviations than those pertaining to compounds made of simple molecules, e.g., air. Furthermore, transonic turbines expanding dense vapors reach critical choking conditions at lower Mach numbers than the ones operating with simple molecules, and are affected by larger dissipation due to viscous mixing.

@en