Circular Image

J.W.G. van de Kuilen

info

Please Note

127 records found

Journal article (2026) - Florian Scharpenack, Andriy Kovryga, Ani Khaloian Sarnaghi, Jan Willem van de Kuilen
Biotic and abiotic climate stressors jeopardize Norway spruce stands, necessitating the evaluation of alternative pathways for structural timber. One promising alternative is the utilization of recovered wood. Dimensional irregularities and design requirements often render reuse infeasible, underscoring the need for processing. Processing corrects dimensional discrepancies; however, prior grading becomes invalid due to cross-sectional changes. To date, there is no German standard for grading recovered wood. Due to additional features compared to new-sawn wood, the applicability of machine grading and the visual standard DIN 4074—1 requires an initial evaluation. This paper experimentally analyzes the general tensile strength of 146 boards (30 × 90 mm2) processed from 22 salvaged rafters. The applicability of DIN 4074—1:2012 is evaluated by assessing visual features and correlating them with tensile properties. Machine grading is evaluated based on an automated scanning process. The findings highlight that visual and machine strength grading are both applicable to the processed recovered wood boards investigated. The graded boards exhibited tensile properties comparable to those of new-sawn wood. In the characterized extent, no impact from fastener holes was observed. ...
Journal article (2026) - Mostafa Abdelrahman, Changxi Yang, Ani Khaloian, Klaus Achterhold, Franz Pfeiffer, Jan Willem Van De Kuilen
This study investigates the fatigue behavior of European ash (Fraxinus excelsior) with density range of 580-620 kg/m3 under relatively short-period cyclic compressive loading. The aim is to understand its mechanical behavior, such as: strain development, recovery, and internal damage mechanisms. Mechanical testings at varying frequencies (0.1, 1.0, and 10 Hz) were performed and the samples were scanned with micro-computed tomography (Micro-CT). Multi-scale assessment of fatigue effects was performed. Strain behavior revealed progressive increases in both viscous and viscoelastic components, demonstrating time- and rate-dependent deformation. For the same loading time, higher loading frequencies resulted in consistently lower accumulated strain; however, no significant differences in strain recovery were observed between frequency groups. Strength and stiffness showed minimal change after up to 2,000 loading cycles at 78 % stress level, highlighting relatively high fatigue resistance of wood under compression. Micro-CT imaging detected internal microcracks in samples pre-loaded with fatigue, inferring that cyclic loading induces more microstructural damage than static conditions. These findings enhance the understanding of the fatigue mechanism in European ash and highlight Micro-CT as a valuable non-destructive tool for internal damage assessment under fatigue loading. ...
Journal article (2026) - Changxi Yang, Mostafa Abdelrahman, Ani Khaloian-Sarnaghi, Yaman Dalal, Jan Willem van de Kuilen
Timber structures are evolving rapidly, featuring increasing spans, greater heights, longer service lives, and a broader range of applications. Some of these applications require a comprehensive understanding of wood’s mechanical behavior, including both creep and fatigue. While wood is known to exhibit nonlinear time-dependent mechanical behavior, existing studies are largely limited to single or static loads, whereas complex load cases, such as varying stress levels or a mixture of fatigue and rheological effects, are underinvestigated. To address this, this study presents an integrated experimental and modeling framework on European ash loaded in longitudinal compression under controlled constant climate conditions. The proposed program employed repeated load–recovery sequences on the same specimen, enabling comparison across multiple stress levels. Three types of loading were studied and compared—ramp, creep, and fatigue at two frequencies (0.1 Hz and 1 Hz). The results revealed elastic, viscoelastic, and viscoplastic strain components across all three loading types. Notably, the irrecoverable strain resulted from both the applied stress level and the duration of the load. Following these observations, a numerical model with a rate-dependent viscoelastic–viscoplastic framework was proposed and calibrated using multi-specimen creep data via a microstructure-based parameter-scaling approach. The calibrated model was used to predict fatigue test results at different frequencies and stress levels. While it captured the time-dependent strain response under sustained loading reasonably well, discrepancies of varying magnitudes were observed relative to the fatigue tests, indicating limitations of the current viscoplastic formulation in describing cyclic strain response. These findings offer new insights about the nonlinear creep and fatigue behavior of complex biomaterials such as wood, and provide opportunities to incorporate additional frequency-dependent mechanisms in advanced applications. ...

A path to low-carbon urbanization for greener societies

Review (2026) - Victor De Araujo, Fernando Mascarenhas, Frederik Laleicke, Andreja Kutnar, Alfredo Dias, Jan van de Kuilen, Martin Hubbe, Francisco Lahr, André Christoforo
By using minerals instead of bioresources in construction, greenhouse gas emissions are nearly doubled. It is vital to transition from this traditional paradigm to a low-carbon model in which woods and bamboos are essential components. To proliferate bio-urbanization, challenges must be overcome in forestry and construction. Our study is a necessary starting point for more sophisticated studies and policies to support the valorization and utilization of bioresources, especially wood and bamboo, in greener construction solutions for a sustainable urbanization. Our main results elucidate examples and benefits of biobased cities and buildings, raise issues and current challenges, and suggest opportune actions to be globally addressed in collaborative proposals. Assertive codes, well-managed resources, resolution of challenges, and clarification campaigns on decarbonization are priority targets in future environmental and societal commitments. ...

Mechanical properties and modified grading rules in DIN 4074-1

Journal article (2026) - Florian Scharpenack, Andriy Kovryga, Jan Willem van de Kuilen
Strength grading is essential to ensure standardized and reliable design processes in timber construction. Current visual strength grading (VSG) standards, such as DIN 4074-1, focus on regulating natural features and grading new sawn timber. Sorting criteria for man-made defects resulting from prior use are lacking. This study examines the potential of VSG for battens processed from salvaged rafters for structural applications and proposes modifications to DIN 4074-1:2012 to make it applicable to battens processed from recovered wood. Battens were visually graded based on natural features, and fastener holes were characterized. Bending strength was tested against EN 338 classes, and the impact of fastener holes was assessed. The results indicate that grades S10 and S13 together account for a total yield of 57%. Clusters of fastener holes reduced bending strength in S10 battens, whereas larger holes affected S13 battens. Modification options for DIN 4074-1:2012 were identified, and their effectiveness was validated. As a result, a new sorting criterion, SRC (strength reducing criteria), was introduced to address the interaction between natural features and fastener holes. Battens processed from recovered wood can serve as an alternative to new timber if classified under the proposed grade W10+. ...
Journal article (2026) - Abhijith Kamath, Jan-Willem van de Kuilen
Phragmites australis L., a widespread vegetation in riparian zones such as rivers and canals, is extensively studied for its ecological benefits such as nutrient removal and hydraulic retention. However, its direct contribution to bank stability through root reinforcement, a key factor for its use in soil bioengineering techniques, has received limited attention. This study investigated the root reinforcement provided by P. australis and its root traits at a soil bioengineering test site on a canal bank in the Province of North-Holland in the Netherlands. Direct measurements of root-soil composite strength were performed using a corkscrew extraction technique at two distinct distances from the canal. Concurrently, root distribution parameters, including Root Area Ratio (RAR) and Root Length Density (RLD), were quantified from extracted soil plugs. Root reinforcement was also indirectly estimated using biomechanical models, incorporating measured root tensile strength and root distribution parameters as inputs. A total of 12 excavations, each 0.25 m2, were conducted for comprehensive root trait analysis at both locations. Direct measurements revealed substantial root reinforcement (max 36 kPa; avg 6–19 kPa). RAR showed effective stabilization values between 0.03 and 0.65 %, peaking at 0.65 % in the area close to canal. Root systems were dominated by fine roots (<0.5 mm diameter), comprising >80 % of total root length and creating dense reinforcing networks. Corkscrew measurements yielded conservative values. Modeled estimates significantly exceeded these field measurements, which is consistent with conventional shear testing. The extensive root surface area (>3.9 m2 m−2) further demonstrates the species' soil-binding capacity, with higher values occurring in hydrologically favorable zones. While the ecological implications of using this widespread species must be contextually considered, its pronounced mechanical reinforcement makes it a highly effective biotechnical tool, particularly in managed environments like canals. ...
Journal article (2026) - Wolfgang Gard, Hanna Botter-Kuisch, Jan Willem van de Kuilen
Brittleheart, also known as compression failure, is a widespread phenomenon observed in numerous tropical wood species, significantly diminishing their strength properties. According to strength grading standards such as BS 5756, NEN 5493 and EN 16,737, timber exhibiting brittleheart characteristics must be rejected. Oftentimes brittleheart remains undetectable on the outer surface and cross-section of sawn timber. This study focuses on qualitatively characterizing compression failures in tropical hardwood and its mechanical properties. In this context, various non-destructive detection methods were explored. Five grades of compression failures were characterized based on the deformation and displacement of wood tissue. Results demonstrate that CT-scanning shows promising as a technique for detecting these five defined grades. Quantitative assessments of brittleheart on the mechanical properties were conducted to determine bending strength (fm) and modulus of elasticity (Em). Multiple regression models were developed to predict the bending strength with a highest coefficient of determination (R²) of 0.778 and a relatively high SEE of 17 N/mm². ...
The majority of bridges in Amsterdam’s historic city centre are built on timber foundation piles, typically 12 to 15 meters in length, which function as end-bearing elements reaching the underlying stiff sand layer. Currently, many timber foundations have been in service for up to 300 years, raising concerns about their remaining load-bearing capacity and the overall safety of the bridges they support. The timber piles beneath the bridges remain fully submerged, where their outer cross-section is exposed to slow bacterial decay in anaerobic conditions, leading to a reduction in the sound load-bearing core of the piles. Despite decay, the piles maintain their structural capacity for many years, although their load-bearing capacity gradually decreases over time. The two primary risks are attributed to the applied loads exceeding the load-bearing capacity of the timber piles, and progressive damage accumulation over time due to sustained loading, ultimately leading to large settlements or failure. In this context, 201 pile segments were extracted from two bridges in Amsterdam and mechanically characterised, with respect to their amount of biological decay and service durations ranging from 100 to 300 years. Large-scale compression tests were carried out to determine the remaining saturated short-term compressive strength of the piles. Micro-drilling measurements were conducted to assess the amount of bacterial decay, validated with Computed Tomography (CT) scanning. On this basis, this study investigates the load history and current loads acting on the timber foundation of Bridge 30 (De Isa van Eeghenbrug) in Amsterdam, to assess the remaining load-bearing capacity of the historical piles, considering mechanical damage and decay as function of time. ...
Journal article (2025) - Changxi Yang, Ani Khaloian-Sarnaghi, Taoyi Yu, Jan Willem van de Kuilen
The strength degradation resulting from duration-of-load (DOL) effect and bacterial decay poses significant challenges to historical timber piles. Many historical European cities still heavily rely on the infrastructure supported by their original timber foundations. A reliable modelling approach on the structural performance of timber piles is needed to avoid the economic loss caused by closing down infrastructure. In this work, we consider a simplified bacterial decay model and develop a numerical framework to integrate the decay model into a standard DOL model. Two approaches are proposed and compared: one considering the homogenised effect of bacterial decay over the entire cross section, and the other taking into account the localised failure accelerated by bacterial decay and applying stiffness reduction to allow stress redistribution. Although the homogenised failure criterion is found to potentially underestimate the effect of bacterial decay, both approaches are able to capture the designated decay pattern. Ultimately, there is a potential for future extension to more intricate loading conditions and decay patterns. ...
Journal article (2025) - Taoyi Yu, Franziska Seeber, Ani Khaloian, Jan Willem van de Kuilen
Humidity fluctuations are a leading cause of damage in wooden constructions. In the case of glulam products, the multitude of possible layups concerning pith locations, diverse material properties across wood species, and the high computational cost associated with multi-field analysis have constrained many research efforts to focus on one specific glulam layup, consequently limiting the generalizability of the findings. To address this challenge, Monte Carlo simulations were employed to assess the significance of various factors. Based on which, two levels of simplification are proposed. The first level reduces the multi-layer problem to a single-layer one by applying appropriate boundary conditions. It substantially reduces the simulation costs and consequently facilitates sophisticated damage analysis, revealing the varying damage pattern across different board types. The second level of simplification further reduces the problem to a single-element model, enabling an analytical estimation of moisture stress. This level of simplification elucidates how factors such as moisture difference, material rotational angle, and other material properties influence the moisture-induced stress. Most importantly, it facilitates a rapid estimation of the critical moisture fluctuation range and the preferred sawing location of boards for different wood species, which can provide guidance to the production of higher moisture resistant glulam. ...
The lack of strength values for timber foundation piles in the current Eurocode 5 hinders their appropriate engineering design and assessment. Timber piles, often submerged for their entire service life, endure high moisture levels, highlighting the need to define strength parameters of round wood under fully saturated conditions. To ensure reliable material properties, a large-scale study was conducted on 70 European softwood piles, determining strength and stiffness through axial compression tests on saturated segments extracted along the pile. Mean and characteristic wet compressive strength and stiffness values were derived, applicable to the whole pile and/or its parts. The mechanical properties of the piles were analysed in relation to grading parameters that may influence the saturated compressive strength, leading to the classification of three strength classes for visual grading. Additionally, two regression models were developed-one based on the most influencing visually graded parameters, and the other on the dynamic modulus of elasticity. The saturated compressive strength values and grading boundaries presented in this study contribute to the engineering design of European softwood foundation piles in the context of a new circular construction ecosystem, and support the integration of reliable design values into future versions of Eurocode 5. ...
Large parts of banks of canals in the Netherlands are protected by azobé timber sheet piles. Many kilometers of sheet piles in the province of Noord-Holland, are planned to be replaced or to undergo maintenance. Yet, there is insufficient knowledge on the current state of the azobé sheet piles and their residual service life. Based on this, a series of investigations on azobé sheet piles after 57 years of service were performed. Visual inspections showed surface deterioration on the water-exposed side for all boards. Nondestructive testing using micro drilling technique showed no signs of internal deterioration. A maximum reduction in thickness of 17% and an average thickness reduction of 6.7% of original thickness were observed. CT scanning showed that the remaining cross sections of the azobé boards were intact and had comparable density of new azobé boards. An exponential damage accumulation model was used to predict the residuals service life of the timber sheet piles subjected to earth stress. Conservative estimates based on physical measurements and residual bending strength indicate that the sheet piles have an additional service life of 22–43 years from the current state. ...
Journal article (2025) - Changxi Yang, Mostafa Abdelrahman, Ani Khaloian-Sarnaghi, Jan Willem van de Kuilen
Fatigue failures pose significant challenges across various engineering disciplines. Wood, due to its low carbon emissions and high strength-to-weight ratio, has been gaining attention in engineering applications. The fatigue behavior of wood is complex due to its heterogeneous, anisotropic, and viscoelastic nature. This research explores essential insights into the fatigue behavior of wood, with a focus on S–N curves, stress–strain behavior, and failure mechanisms. Due to often varying failure criteria and test settings, direct comparison of S–N curves across different studies can be challenging and inconclusive. A closer look shows that wood in fatigue shows both irreversible and recoverable strain components that are delayed. However, there have been conflicting reports about residual stiffness changes under fatigue loading. Theoretical fatigue life models based on S–N curves or duration of load theory have shown limited applicability. Efforts to develop progressive damage model based on stress–strain behaviors have been challenging and largely unsuccessful due to the lack or inconsistency of data. Understanding the microstructural failure mechanism is crucial in order to build a more trustworthy fatigue modeling technique. Further work is suggested to monitor the microstructural deterioration during high-cycle fatigue loading. ...
Journal article (2025) - Taoyi Yu, Ani Khaloian, Jan Willem van de Kuilen
This study examines the spring-back effect and residual stresses in curved glued-laminated timber (glulam) beams during the manufacturing process. In addition to curving along the longitudinal axis (X), a cup-deformation develops in the transverse direction (Z) due to the Poisson's effect. This deformation, combined with the glue-hardening process and the release of pressure, leads to the development of residual stresses in all three axial directions, as well as shear stresses within individual boards and at their interfaces. Besides the well-known factors such as longitudinal elasticity, board thickness, and inner radius, the study reveals that the number of layers (n) and Poisson's ratio (νLT) significantly influence the magnitude of residual stresses. However, aside from longitudinal stresses, the impact of n and νLT, as well as other residual stresses, have been scarcely studied and are not adequately addressed in current design standards. A Monte–Carlo analysis of the growth-ring effect is conducted, taking the pith location of different board layers as the input random variable. Strong influences can be identified on the residual stresses in both radial and tangential directions, with intensified maximum values and more scattered distribution inside the cross-section. The time- and moisture-dependent relaxation analysis using the rheological wood model shows a significant influence of the temperature and relative humidity. ...

Impact of developmental growth levels on mechanical properties

Trees can adapt to external loads and form inosculations (self-growing connections), where stems or branches naturally fuse together. However, a limited understanding of biomechanical features of connections hinders their practical applications. This study used connections formed by Ficus benjamina L. to investigate their mechanical properties at different growth levels. Two parameters (fusion degree and interface curvature) were identified to describe growth levels. Customized tensile tests were designed to measure mechanical properties perpendicular to the interconnected surface. Growth levels of studied connections ranged from initial formation to almost fusion of piths, which provided a range of tensile strength of 0.23 to 1.38 MPa. Two primary failure modes (failure at the interface and failure across the stems) were found to be linked to growth levels. The fusion degree, at approximately 15%, contributed to distinguishing failure modes. The average diameter of a connection had the most significant effect on its tensile strength and stiffness. Moreover, the interface curvature correlated negatively with mechanical properties. Average diameter, interface curvature, and fusion degree were effective predictors of connections’ tensile strength. Regarding Ficus connections, dry connections were stronger than wet connections. These findings provide evidence for nature-based design using self-growing connections under different moisture conditions and growth levels. ...

Techniques for the assessment of their state of conservation

Journal article (2025) - Giorgio Pagella, Tiziana Urso, Michele Mirra, Silvia Naldini, Jan-Willem van de Kuilen
This study explored the most employed techniques for the assessment of the state of conservation of traditional wooden foundation piles in Amsterdam and Venice. The techniques were evaluated for their relevance and effectiveness in assessing decay impact on centuries-old waterlogged wooden piles. The techniques adopted in Amsterdam and Venice were complementary. In Amsterdam, underwater micro-drilling was employed to accurately estimate the amount of decay and the remaining strength of the piles. In contrast, the techniques in Venice were based on microscopic and mechanical testing of small wood samples to provide a detailed decay analysis. The successful use of underwater micro-drilling in Amsterdam, which allows for fast and accurate pile decay assessment, presents an opportunity to enhance the piles conservation database of Venice. Adopting this technique in Venice could support more timely and effective preservation strategies. ...
Conference paper (2025) - Florian Böhm, Sajjad Jubair, Andriy Kovryga, Jan Willem van de Kuilen
Extending the service life of building components is essential for a circular economy. Wood, as a renewable raw material, plays due to its mechanical properties and ease of processing a crucial role in this process. Most studies focus on the reuse of building materials. However, it is essential to detect and investigate the use cases in which reuse is impossible due to changing dimensional requirements or damages. This study examines the bending properties of recovered wood, particularly battens with cross-sectional dimensions of 30x50 mm2, which were processed from rafters originating from a roof truss deconstructed in southern Germany. The bending tests were performed and interpreted based on the damages of the prior use and the lumber pieces' background information. The visual observation resulted in many fastener holes, mainly derived for battens from the built-in upper layer of the rafters. Even though fastener holes contributed to or were the single cause for the failure of the battens, bending strength around the mean value or even higher was yet achieved for some battens. Developing unique sawing patterns for each rafter by taking into account the location of the pith and the arrangement of knots can enhance the yield. Additionally, introducing a third grade, S7, alongside the existing S10 and S13 grades - similar to the approach used for joists and boards in DIN 4074-1:2012 - could further optimize yield. Although it has been concluded that knots remain even for recovered wood the key sorting criteria, fastener holes, can additionally influence the mechanical properties and, therefore, need to be considered in a standardized strength grading. ...
Conference paper (2025) - J. W.G. van de Kuilen, P. A. de Vries, J. J.B. Debije, J. H.P. Hover, W. F. Gard, G. J.P. Ravenshorst
Laminated bamboo can be produced in sizes that are similar to glued laminated timber. Asaresult, large connections with multiple dowels and slotted-in steel plates are similarly possible with bamboo. MOSO bamboo was used in this study, withadensity of around 660 kg/m3, potentially creating connections having higher load carrying capacity than softwood. A large experimental campaign was set-up in order to determine the mechanical properties of connections with various ratios of dowel diameter to bamboo thicknesses and with single and double steel plates. Furthermore, influences of the density of the material, related to the embedding strength for fasteners, as well as the splitting sensitivity with multiple fasteners inarow are playing crucial roles with respect to the load carrying capacity. Therefore, multiple test series on large bamboo connections have been performed in order to study various possible failure modes, as dependent on embedding strength, steel grade, number of fasteners inarow, and the influence of multiple steel plates. The various failure modes have been analysed analytically with the Johansen equations, similar to the design equations proposed for the upcoming version of Eurocode 5 for multiple steel plate connections, confirming their applicability to bamboo and its similarity with wood. ...
Journal article (2025) - Franziska Seeber, Ani Khaloian-Sarnaghi, Elena Benvenuti, Jan Willem van de Kuilen
This contribution aims to increase the understanding of the complex mechanical behavior of wood through a framework for simulating mixed-mode failure. Based on physical properties assessment, appropriate constitutive laws, and experimental validation, a generally applicable numerical strength prediction tool for wood from different species and with various natural imperfections is introduced. The 3D orthotropic elastic plastic non-local CDM model considers the local fiber orientation and is implemented as material subroutines in the commercial software Abaqus. Herein, orthotropic Hill-plasticity with exponential hardening represents the plastic behavior in compression. Separated stress-based gradient-enhanced transient non-local damage represents the brittle material behavior in tension and shear. The methodology is validated with experimental data on tensile veneer tests, shear- and compression tests. Moreover, the methodology is applied to four-point bending tests of boards with heterogeneities. The numerical results demonstrate that the proposed model is able to reproduce different crack patterns observed in the four-point bending tests. Detailed investigations of the impact on the strength of the boards can be performed with this method to optimize species-independent strength prediction and engineered wood products. Further combination with other material laws e.g. moisture is possible. ...
Journal article (2025) - Franziska Seeber, Ani Khaloian-Sarnaghi, Elena Benvenuti, Fabian Duddeck, Jan Willem van de Kuilen
Reliable finite element simulation of orthotropic-dependent failure mechanisms is crucial for understanding the mechanical behavior and optimizing engineered composites and fiber-based materials. Such materials behave brittle under tension and strongly depend on the orthotropic material orientation. Existing non-local models can reproduce brittle fracture for isotropic materials but, in most cases, they are based on the equivalent strain concept for damage initiation, which is unsuitable for orthotropic materials. This contribution introduces a stress-based non-local damage model enhanced with an implicit gradient formulation of the failure criteria. A localizing non-local length is assumed to avoid any pathological broadening of the damage band. The methodology introduces direction-dependent damage variables driven by non-local stress-based damage criteria and can thus distinguish different failure modes. The verification and validation are shown on numerical and experimental benchmark examples. The implicit gradient-based non-local damage approach allows mesh-independent results. Furthermore, it does not require a priori known crack paths and makes it possible to simulate complex failure modes. Perspectively, its effective implementation in the commercial software Abaqus and combination with other constitutive laws, e.g. to account for plasticity or moisture, make it an attractive tool for describing the mechanical material behavior of orthotropic materials, such as wood and fiber-composites. ...