Floating offshore wind (FOW) is a renewable energy source that is set to play an essential role in addressing climate change and the need for sustainable development. However, due to the increasing threat of climate emergency, more wind turbines are required to be deployed in deep water locations, further offshore. This presents heightened challenges for accessing the turbines and performing maintenance, leading to increased costs. Naturally, methods to reduce operational expenditure (OpEx) are highly desirable. One method that shows potential for reducing OpEx of FOW is LIDAR-assisted pitch control. This approach uses wind velocity measurements from a nacelle-mounted LIDAR to enable feedforward control of floating offshore wind turbines (FOWTs) and can result in reductions to the variations of structural loads. Results obtained from a previous study of combined feedforward collective and individual pitch control (FFCPC + FFIPC) are translated to OpEx reductions via reduced component failure rates for future FOW developments, namely, in locations awarded in the recent ScotWind leasing round. The results indicate that LIDAR-assisted pitch control may allow for an up to 5% reduction in OpEx, increasing to up to 11% with workability constraints included. The results varied across the three ScotWind sites considered, with sites furthest from shore reaping the greatest benefit from LIDAR-assisted control. This work highlights the potential savings and reduction in the overall levelised cost of energy for future offshore wind turbine projects deliverable through the implementation of LIDAR-assisted pitch control.

As new offshore wind development sites move further from shore and existing sites enter their post-subsidy operating period, it is expected that operational expenditure (OpEx) will increase. In order to overcome these challenges, a more flexible and cost-effective maintenance solution is needed. One such solution is opportunistic maintenance (OM). This work provides an overview of the maintenance strategy used within other industries before providing an in-depth review of the work specific to offshore wind. The existing literature fails to agree on the specific definition of the term. This work proposes an all-encompassing definition of the term, reviewing maintenance ‘opportunities’ and their corresponding ‘action/response’. The review found that maintenance opportunities are either internal or weather-based, with each opportunity having a pre-determined trigger/response. This work proposes the introduction of a market-based opportunity, which has not been previously considered. As offshore wind farms now face increasing curtailment and negative pricing threats, this new OM framework, OM+, view these periods as maintenance opportunities. OM+ also provides a new definition for recording and reporting availability — moving from time/energy-based availability to market-based availability.

The upscaling of wind turbines results in fewer units per installed MW reducing infrastructure and maintenance costs of offshore wind farms. Multi rotor systems (MRS), comprising many wind turbine rotors on a single support structure, are potentially a means to maximize the upscaling benefit in achieving larger unit capacities than is feasible or economic with the conventional, 3-bladed horizontal axis wind turbine (HAWT). The MRS has an inherent upscaling advantage which, for a system with many rotors compared to a single rotor, reduces the total weight and cost of rotor-nacelle assemblies by a large factor. An innovative MRS design is presented based on vertical axis wind turbine (VAWT) rotors of the 2-bladed, H-type. Many disadvantages of VAWT design compared to HAWT in a single rotor system (reduced power performance and higher drive train torque, for example) are resolved in the MRS configuration. In addition, reduced component number and simpler components is advantageous for reliability and O&M cost. This MRS concept has many synergies arising from the choice of VAWT rotors. Results comprise a high-level evaluation of system characteristics and the first stage of more detailed investigation of aerodynamics of the high aspect ratio VAWT.

New wind turbine technologies and designs are being explored in order to reduce the cost of energy from offshore wind farms. Two potential routes to a lower cost of energy are the X- Rotor Concept (XRC) and Multi-Rotor System (MRS) turbines. A key cost saving for both Novel concepts included in this paper is operation and maintenance (O&M) costs savings. The major component replacement cost for conventional horizontal axis, XRC and MRS turbines are examined and the benefits of the concepts are provided in this paper. A review on existing decision support systems for offshore wind farm O&M planning is presented with a focus on how applicable these previous models are to novel turbine concepts, along with analysis of how the influential factors can be modified to effectively model XRC and MRS.

As the installed capacity of individual turbines increases, so do costs associated with manufacture and maintenance. One proposed solution to this problem is the Multi-Rotor System (MRS) which utilises many small rotors to yield the same energy capture as a single large turbine. The operational advantage of the MRS is the built in redundancy between rotors on the same structure. However, despite this advantage, an increase in number of components is likely to result in an increase in transfers. This work examines the balance between additional crew and vessel requirements for such a structure against the expected savings in downtime due to redundancy and small rotor power rating. Three scenarios are analysed to determine the distribution of the failures which contribute to downtime. The study aims to find the optimal vessel fleet which limits downtime without drastically increasing direct operational expenditure (OpEx). As site size increases, the impact of global failures, which shut down the whole asset, is lessened. However, there is a significant increase in the number of vessels required to reduce downtime to <10% of the total OpEx. While a large fleet can offer significant downtime savings, there are practical limitations and challenges which must be acknowledged.

This paper presents the key operations & maintenance (O&M) modelling inputs for fixed-bottom wind (FBW) and highlights the adaptations required for floating offshore wind (FOW) uses. The work also highlights major repair strategies such as tow to shore (T2S) and discusses the limitations and constraints which arise in an operational context. The technical and economic feasibility of such O&M strategies requires rethinking of weather risks and constraints, new vessel technologies and operational costs. The work also collates and reviews existing FBW models which have been adapted for FOW uses and analyses O&M inputs for a tow to shore operation. Findings show that there is ambiguity in literature for tug speeds and disconnection/reconnection times of the turbine system. A performed case study investigates the sensitives of both parameters through a weather window analysis of ScotWind sites. Recommendations for future practises, including additional O&M modelling considerations and inputs for FOW uses are given.