Horizontal stirred bed reactors are widely used in the commercial manufacturing of polypropylene. However, a comprehensive understanding of the particle dynamics in horizontal stirred bed reactors remains elusive, primarily due to the lack of detailed experimental data. In this work, we studied the influence of operating parameters on the particle flow dynamics in a laboratory-scale horizontal stirred bed reactor using single-photon emission radioactive particle tracking. The results show that the general solids flow behavior is strongly affected by both the agitator rotation speed and reactor fill level. Operation at low rotation speed and low fill level results in solids flow with poor radial and circumferential distribution due to internal bed circulation. On the contrary, at increased rotation speeds and fill levels, solids motion throughout the bed is continuous resulting in excellent solids distribution. The solids circulation was found to increase for both an increase in rotation speed and reactor fill level. The axial dispersion coefficient, on the other hand, shows a linear relation with the rotation speed, but no conclusive relation between the axial dispersion coefficient and the reactor fill level was found.

@en

This study introduces a mathematical model to predict the dynamic angle of repose exhibited by granular materials in a rotating drum. The model accounts for the effect of particle properties, particularly sliding and rolling friction, as well as process conditions, i.e., the Froude number. We show that the effects of particle properties can be modeled independently of the process conditions, resulting in a multiplicative model. The model is validated using experimental data taken at different Froude numbers, yielding favorable agreement between the predicted dynamic angle of repose and the experimental observations. The findings of this study hold significant implications for engineering disciplines, as they provide crucial insights for optimizing processes involving granular materials in various engineering applications.@en

Vibro-assisted fluidization of cohesive micro-silica has been studied by means of X-ray imaging, pressure drop measurements, and off-line determination of the agglomerate size. Pressure drop and bed height development could be explained by observable phenomena taking place in the bed; slugging, channeling, fluidization or densification. It was observed that channeling is the main cause of poor fluidization of the micro-silica, resulting in poor gas-solid contact and little internal mixing. Improvement in fluidization upon starting the mechanical vibration was achieved by disrupting the channels. Agglomerate sizes were found to not significantly change during experiments.

@en

Evaluation of the hydrodynamics of opaque multi-phase flows remains a challenging task, with implications for various industrial processes such as chemical processing, pharmaceutical, and mineral processing. Understanding how design and operational variables affect the complex behavior of multi-phase flow systems is essential for optimizing processing conditions and improving efficiency. Radioactive particle tracking (RPT) has been a proven measurement technique to evaluate hydrodynamics in multi-phase flow systems. However, a limitation of the classical RPT technique exists in the assumptions made in the simulation of the count rate received by the detectors in correcting for varying flow-induced fluctuations in the volume fraction of the dispersed phase, often encountered in industrial multi-phase flow systems. In this paper, we introduce a fundamentally novel experimental RPT method that directly uses detected incident photon hit locations for the reconstruction of the three-dimensional radioactive tracer particle position. We argue that this approach is inherently more robust as varying attenuation does not affect the reconstruction. The RPT setup consists of three identical γ-radiation slit collimator detectors that are placed equidistantly at 120° intervals. A subsequent calibration-experimentation procedure is established that allows reconstruction of the tracer particle position with spatial accuracy and precision in the order of 1 mm. We demonstrate the applications of this technique in evaluating hydrodynamics in multi-phase systems by characterizing the flow field of industrial-grade polypropylene reactor powder in a laboratory-scale horizontal stirred bed reactor.

@en

Stirred gas–solid fluidized bed reactors are commercially employed in polyolefin manufacturing, but the complex gas–solid contacting dynamics pose challenges in design, scale-up, and operation. In this study, the influence of agitation on the fluidization performance of Geldart B particles was investigated experimentally by X-ray imaging and pressure drop measurements and numerically by Computational Fluid Dynamics (CFD) - Discrete Element Method (DEM) - Immersed Boundary Method (IBM). The experimentally obtained minimum fluidization curve and time-averaged pressure drop show good qualitative agreement with the simulation results. Visual observations underscore that an increase in the angular velocity of the agitator results in reduced bubble size and improved bed homogeneity, as further evidenced by reduced pressure fluctuations. Furthermore, the simulations reveal that while the impeller enhances solids agitation, a proper design study is imperative, considering that static immersed bodies, such as the stirrer shaft, can adversely impact solids motion.@en