Autonomous robots are used to inspect, repair and maintain underwater assets. These tasks require energy-efficient robots, including efficient movement to extend available operational time. To examine the suitability of a propulsion system based on undulating fins, we built two robots with one and two fins, respectively, and conducted a parametric study for combinations of frequency, amplitude, wavenumber and fin shapes in free-swimming experiments, measuring steady-state swimming speed, power consumption and cost of transport. The following trends emerged for both robots. Swimming speed was more strongly affected by frequency than amplitude across the examined wavenumbers and fin heights. Power consumption was sensitive to frequency at low wavenumbers, and increasingly sensitive to amplitude at high wavenumbers. This increasing sensitivity of amplitude was more pronounced in tall rather than short fins. Cost of transport showed a complex relation with fin size and kinematics and changed drastically across the mapped parameter space. At equal fin kinematics as the single-finned robot, the double-finned robot swam slightly faster (>10%) with slightly lower power consumption (<20%) and cost of transport (<40%). Overall, the robots perform similarly to finned biological swimmers and other bio-inspired robots, but do not outperform robots with conventional propulsion systems.

@en

To generate aerodynamic forces required for flight, two-winged insects (Diptera) move their wings back and forth at high wing-beat frequencies. This results in exceptionally high wing-stroke accelerations, and consequently relatively high acceleration-dependent fluid forces. Quasi-steady fluid force models have reasonable success in relating the generated aerodynamic forces to the instantaneous wing motion kinematics. However, existing approaches model the stroke-rate and stroke-acceleration effects independently from each other, which might be too simplified for capturing the complex unsteady aerodynamics of accelerating wings. Here, we use computational-fluid-dynamics simulations to systematically explore how aerodynamic forces and flow dynamics depend on wing-stroke rate, wing-stroke acceleration and wing-planform geometry. Based on this, we developed and calibrated a novel unsteady aerodynamic force model for insect wings with stroke accelerations. This includes improved versions of the translational-force model and the added-mass force model, and we identify a third novel component generated by the interaction of the two. This term reflects the delay in bound-circulation build-up as the wing accelerates. The physical interpretation of this effect is analogous to the Wagner effect experienced by a wing starting from rest. Here, we show that this effect can be modelled in the context of flapping wings as a stroke-acceleration-dependent correction on the translational-force model. Our revised added-mass model includes a viscous force component, which is relatively small but not negligible. We subsequently applied our new model to realistic wing-beat kinematics of hovering Dipteran insects, in a quasi-steady approach. This revealed that stroke-acceleration-related aerodynamic forces contribute substantially to lift and drag production, particularly for high-frequency flapping mosquito wings.

@en

When approaching a landing surface, many flying animals use visual feedback to control their landing. Here, we studied how foraging bumblebees (Bombus terrestris) use radial optic expansion cues to control in-flight decelerations during landing. By analyzing the flight dynamics of 4,672 landing maneuvers, we showed that landing bumblebees exhibit a series of deceleration bouts, unlike landing honeybees that continuously decelerate. During each bout, the bumblebee keeps its relative rate of optical expansion constant, and from one bout to the next, the bumblebee tends to shift to a higher, constant relative rate of expansion. This modular landing strategy is relatively fast compared to the strategy described for honeybees and results in approach dynamics that is strikingly similar to that of pigeons and hummingbirds. The here discovered modular landing strategy of bumblebees helps explaining why these important pollinators in nature and horticulture can forage effectively in challenging conditions; moreover, it has potential for bio-inspired landing strategies in flying robots.

@en

The adhesive toe pads of tree frogs have inspired the design of various so-called 'smooth' synthetic adhesives for wet environments. However, these adhesives do not reach the attachment performance of their biological models in terms of contact formation, maintenance of attachment, and detachment. In tree frogs, attachment is facilitated by an interconnected ensemble of superficial and internal morphological components, which together form a functional unit. To help bridging the gap between biological and bioinspired adhesives, in this review, we (1) provide an overview of the functional components of tree frog toe pads, (2) investigate which of these components (and attachment mechanisms implemented therein) have already been transferred into synthetic adhesives, and (3) highlight functional analogies between existing synthetic adhesives and tree frogs regarding the fundamental mechanisms of attachment. We found that most existing tree-frog-inspired adhesives mimic the micropatterned surface of the ventral epidermis of frog pads. Geometrical and material properties differ between these synthetic adhesives and their biological model, which indicates similarity in appearance rather than function. Important internal functional components such as fiber-reinforcement and muscle fibers for attachment control have not been considered in the design of tree-frog-inspired adhesives. Experimental work on tree-frog-inspired adhesives suggests that the micropatterning of adhesives with low-aspect-ratio pillars enables crack arresting and the drainage of interstitial liquids, which both facilitate the generation of van der Waals forces. Our analysis of experimental work on tree-frog-inspired adhesives indicates that interstitial liquids such as the mucus secreted by tree frogs play a role in detachment. Based on these findings, we provide suggestions for the future design of biomimetic adhesives. Specifically, we propose to implement internal fiber-reinforcements inspired by the fibrous structures in frog pads to create mechanically reinforced soft adhesives for high-load applications. Contractile components may stimulate the design of actuated synthetic adhesives with fine-tunable control of attachment strength. An integrative approach is needed for the design of tree-frog-inspired adhesives that are functionally analogous with their biological paradigm.@en

Hemipterans, mosquitoes, and parasitic wasps probe in a variety of substrates to find hosts for their larvae or food sources. Probes capable of sensing and precise steering enable insects to navigate through solid substrates without visual information and to reach targets that are hidden deep inside the substrate. The probes belong to non-related taxa and originate from abdominal structures (wasps) or mouthparts (hemipterans and mosquitoes), but nevertheless share several morphological characteristics. Although the transport function clearly differs (egg laying and acquisition of liquid food), the functional demands on the mechanical behaviour of the probe within the substrate tend to be similar. The probe needs to be thin to limit substrate deformation, and long, in order to attain substantial path lengths or depths. We linked the morphology across taxa to the different functional requirements, to provide insights into the biology of probing insects and the evolution of their probes. Current knowledge of insect probes is spread over many taxa, which offers the possibility to derive general characteristics of insect probing. Buckling during initial puncturing is limited by external support mechanisms. The probe itself consist of multiple (3–6) parts capable of sliding along one another. This multi-part construction presumably enables advancement and precise three-dimensional steering of the probe through the substrate with very low net external pushing forces, preventing buckling during substrate penetration. From a mechanical viewpoint, a minimum of three elements is required for 3D steering and volumetric exploration, as realised in the ovipositors of wasps. More elements, such as in six-element probes of mosquitoes, may enhance friction in soft substrates. Alternatively, additional elements can have functions other than ‘drilling’, such as saliva injection in mosquitoes. Despite the gross similarities, probes show differences in their cross sections, tip morphologies, relative lengths of their elements, and the shape of their interconnections. The hypothesis is that the probe morphology is influenced by the substrate properties, which are mostly unknown. Correlating the observed diversity to substrate-specific functional demands is therefore currently impossible. We conclude that a multipart probe with sliding elements is highly effective for volumetric substrate probing. Shared functional demands have led to an evolutionary convergence of slender multi-element probes in disparate insect taxa. To fully understand 3D probing, it is necessary to study the sensory and material properties, as well as the detailed kinematics and dynamics of the various probes in relation to the nature of the selective pressure originating from the species-specific substrates. Such knowledge will deepen our understanding of probing mechanisms and may support the development of slender, bio-inspired probes.

@en

Tree frogs have the remarkable ability to attach to smooth, rough, dry, and wet surfaces using their versatile toe pads. Tree frog attachment involves the secretion of mucus into the pad-substrate gap, requiring adaptations towards mucus drainage and pad lubrication. Here, we present an overview of tree frog attachment, with focus on (i) the morphology and material of the toe pad; (ii) the functional demands on the toe pad arising from ecology, lifestyle, and phylogenetics; (iii) experimental data of attachment performance such as adhesion and friction forces; and (iv) potential perspectives on future developments in the field. By revisiting reported data and observations, we discuss the involved mechanisms of attachment and propose new hypotheses for further research. Among others, we address the following questions: Do capillary and hydrodynamic forces explain the strong friction of the toe pads directly, or indirectly by promoting dry attachment mechanisms? If friction primarily relies on van der Waals (vdW) forces instead, how much do these forces contribute to adhesion in the wet environment tree frogs live in and what role does the mucus play? We show that both pad morphology and measured attachment performance suggest the coaction of several attachment mechanisms (e.g. capillary and hydrodynamic adhesion, mechanical interlocking, and vdW forces) with situation-dependent relative importance. Current analytical models of capillary and hydrodynamic adhesion, caused by the secreted mucus and by environmental liquids, do not capture the contributions of these mechanisms in a comprehensive and accurate way. We argue that the soft pad material and a hierarchical surface pattern on the ventral pad surface enhance the effective contact area and facilitate gap-closure by macro- to nanoscopic drainage of interstitial liquids, which may give rise to a significant contribution of vdW interactions to tree frog attachment. Increasing the comprehension of the complex mechanism of tree frog attachment contributes to a better understanding of other biological attachment systems (e.g. in geckos and insects) and is expected to stimulate the development of a wide array of bioinspired adhesive applications.

@en