Oxidative aging induces significant stiffening of asphalt binders that leads to a pronounced reduction in the overall durability of asphalt pavements. The strategic implementation of antioxidant additives provides a potential solution to alleviate this issue. This work presents results from the second phase of the global consortium for antioxidants research aimed at investigating the effectiveness of potential antioxidants in increasing the durability of asphalt binders. Sixteen laboratories around the world participated in this effort and a total of 28 binders from diverse geographical regions were tested. Two promising antioxidants, namely zinc diethyldithiocarbamate (ZDC) and kraft lignin were evaluated in this phase and blended with the binders at specific proportions. Subsequently, a comprehensive investigation was conducted to assess rheological characteristics and chemical properties of the various blends, utilising Dynamic Shear Rheometer (DSR) measurements and Fourier Transform Infrared (FTIR) Spectroscopy. The findings indicate that additives such as ZDC hold considerable promise as an effective antioxidant, particularly when considering a wide diversity of binders. In general, its incorporation does not compromise the rutting performance of the binders and significantly improves fatigue performance. Therefore, research efforts should be focused on exploring additional facets to assess its practical applicability in field.

@en

The chemical characterization of bitumen type and ageing state are fundamental in determining structural and mechanical properties of bitumen. This work aims to classify various bitumen types at different ageing states and to identify the primary chemical differences relevant to the classification. Fourier transform infrared (FTIR) spectral data of eight bitumen types at five ageing states were analyzed using a chemometric procedure that incorporates principal component analysis (PCA), linear discriminant analysis (LDA) models, variable selection methods. The models presented results of high accuracy in differentiating bitumen type and ageing state. The results show that the spectral regions that describe the aliphatic and aromatic bonds are critical to the identification of bitumen types. The chemical changes due to bitumen ageing are mainly revealed at the region of 1800–900 cm-1. This chemometric method is instructive for the characterization of chemical bitumen properties.

@en

This study aims to multiscale investigate the effects of rejuvenator type, temperature, and aging degree of bitumen on the diffusion behaviors of rejuvenators (bio-oil BO, engine-oil EO, naphthenic-oil NO, and aromatic-oil AO) in aged binders. The molecular dynamics (MD) simulation method is performed to detect the molecular-level diffusion characteristics of rejuvenators and predict their diffusion coefficient (D) parameters. At an atomic scale, the mutual but partial interfacial diffusion feature between rejuvenators and aged bitumen molecules is observed. Moreover, Fick’s Second Law well fits the concentration distribution of rejuvenator molecules in aged bitumen. The magnitude for D values of four rejuvenators varies from 10-11 to 10-10 m2/s, and the diffusive capacity order is BO > EO > NO > AO. Meanwhile, diffusion tests and dynamic shear rheometer (DSR) characterizations are employed to validate the MD simulation outputs. The experimental results in magnitude and order of D values agree well with MD simulation outputs. Lastly, the increased aging degree of bitumen exhibits a negative impact on the molecular diffusivity of BO, EO, and NO rejuvenators, while the D value of AO molecules enlarges as the aging level deepens. The underlying mechanism may be composed of the free volume fraction in aged bitumen and the intermolecular force between rejuvenator and aged bitumen molecules, which differs remarkably for various rejuvenators.@en

This research aims to evaluate the potential environmental impact of epoxy-modified asphalt used as a pavement material for roadways in the Netherlands and identify what determines the environmental performance of the epoxy asphalt technology through life cycle assessment. Results indicated that the incor-poration of epoxy binder in asphalt could lead to significantly lower environmental impact than the unmodi-fied asphalt. Such benefits are attributed by the minimal maintenance interventions of a pavement with epoxy and their remarkably higher service life over the analysis period. Finally, although the initial price of epoxy-modified asphalt production and construction was substantially higher than of standard asphalt mixtures, the overall score of epoxy-modified asphalt pavement in all weight scenarios was lower than that of the reference structures reflecting the sustainability benefits of using this technology for roadway pavements.@en

The design and use of antioxidant additives to reduce or slow down the aging of asphalt binders can bring about tremendous benefits to the asphalt industry. Despite many isolated and scattered research efforts showing mixed results, the application of this science to engineering-based solutions has been limited due to variability in results and conflicting data available. This work presents the results from a global interlaboratory study to test the effectiveness of promising antioxidant additives, namely kraft lignin, calcium hydroxide, zinc diethyldithiocarbamate and phenothiazine to increase the resilience of asphalt binders and provide insights towards understanding the complex intricacies between chemistry and rheology. Specifically, seven different binders from various geographical regions in the world i.e., Texas (USA), Vienna (Austria), Illinois (USA), Antwerp (Belgium), and Delft (Netherlands) were blended with the antioxidants at two proportions. Subsequently, the chemical and rheological properties of the blends were evaluated using Fourier transform infrared (FTIR) spectroscopy and dynamic shear rheometer (DSR). The results indicate that although some antioxidants may reduce oxidation based chemical indices, their effect on rheology is more complicated and possibly related to unique physicochemical interactions in each binder. From a macro-perspective, zinc diethyldithiocarbamate showed promising results with a good correlation between rheology and chemistry for the majority of the binders. These additives or other additives with the same working principles should be investigated further. Additionally, significant research efforts must also be directed towards approaches aimed at understanding mechanisms of interaction and relating results with specific binder compositions.@en

The rejuvenation efficiency of aged bitumen is the main concern when developing rejuvenating agents. It is necessary to develop a method to assess the efficiency of rejuvenators using rheological parameters in the whole frequency region. To this end, the 2S2P1D micromechanics model is adopted to fit the entire G∗ master curves of various rejuvenated bitumen, and the influence of rejuvenator type/dosage and aging grade of bitumen on the whole G∗ master curve and chemical indices are investigated. Critical parameters for evaluating rejuvenation efficiency derived from viscoelastic models and chemical characterizations are proposed. Furthermore, the potential relationships between the rheological model-based parameters (E _∞, δ, β, and τ) and chemical indices (carbonyl index CI and sulfoxide index SI) are explored. The results indicate that rejuvenators restore the δ, τ, CI, and SI values of aged bitumen towards the virgin bitumen level. The E _∞ parameter is not applicable to evaluate the rejuvenation efficiency of engine-oil and naphthenic-oil rejuvenators, but the positive E _∞R values of bio-oil and aromatic-oil rejuvenated bitumen are detected. All rejuvenators fail to restore the β parameter of aged bitumen. The τ and CI parameters are selected as critical evaluation indicators from the perspective of viscoelastic models and chemical characteristics. Linear correlations between all rheological parameters and chemical indices are observed and established.

@en

RILEM TC-279 WMR task group TG 1 studied the performance of waste Polyethylene (PE) in bituminous binders and bituminous mixtures. Several laboratories participated in this study following a common protocol. Locally sources aggregates and bituminous binder and same source of waste PE were utilized. The binder experiments showed that at high temperatures, using MSCR tests, PE modified blends had better resistance to permanent deformation in comparison to the non modified binder. Whereas at intermediate temperatures, using the LAS tests, fatigue performance of the PE blends could withstand more loading cycles under low strains; however, it could sustain less loading cycles under high strains due to the increase in brittleness. Dry process was used for the mixture experiments in order to bypass the stability and inhomogeneity experience that was observed at the binder scale. The PE modified mixtures showed improved workability and increased strength. The higher the PE dosage, the higher the ITS increase with respect to the values measured for the control materials (i.e., without any plastic waste) thanks to the improved cohesion of the plastic modified mastic. The stiffness experiments tended to show an improved performance with a lower time dependence and a higher elasticity when plastic was added. The cyclic compression tests demonstrated a reduced creep rate along with a higher creep modulus thanks to the addition of PE; similar conclusions can be drawn from the experimental findings coming from wheel tracking test. Furthermore, acceptable and often improved moisture resistance was observed for PE modified materials.

@en

Two types of elastomer/plastic compound-modified bitumen were developed by means of incorporating the reactive elastomeric terpolymer (RET) into the plastic (high-density polyethylene HDPE or recycled polyethylene RPE) modified bitumen and adding the wax residue (WR) into the bitumen/elastomer (crumb rubber CR or styrene–butadiene–styrene SBS) blends. The rheological properties, morphology microstructure and storage stability of these novel elastomer/plastic compound-modified binders were characterised. The results revealed that RET elastomer positively improved the high-temperature modulus, temperature insensitivity, rut resistant, elastic recovery and shear-resistance of HDPE- and RPE-modified bitumen. However, excessive RET dosage adversely influenced the cracking resistance of plastic-modified bitumen, and its optimum dosage was recommended as 1 wt%. Moreover, RET elastomer significantly strengthened the storage stability of HDPE and RPE-modified binders. The elasticity improvement effect of RET was attributed to the generated polymer network. On the other hand, adding WR limitedly deteriorated the rutting resistance and weakened the elastic recovery performance of elastomer (CR and SBS) modified bitumen. To ensure the low-temperature performance, the optimum level of WR was 2 wt%. Furthermore, the addition of WR promoted the compatibility and dispersion of CR and SBS modifiers in bitumen.@en

Water transport is one of the major factors responsible for moisture damage in asphalt pavements. To study the thermodynamics and kinetics of water transport in bitumen and to uncover microscale mechanisms of moisture-induced damage, molecular dynamics simulations were performed for up to 600 ns for water–bitumen systems with realistic water contents that varied from 0 to 1.76 wt%. Hydrogen bonding interactions and clustering of water molecules at various combinations of temperature and water content were investigated, and their effects on the self-diffusion coefficient of water and bitumen properties are computed and discussed. It is shown that the saturated water concentration in bitumen is small, especially at low temperatures, and additional water molecules tend to form large water clusters via hydrogen bonding, indicating micro-phase separation of the water and bitumen phases inside the simulation box. Hydrogen bonding and water clustering play a crucial role on the magnitude of the self-diffusion coefficient of water. Physical properties of bitumen that include viscosity and cohesive energy are affected by water. The presence of large water clusters is indicative of how degradation in cohesion is observed on the microscale.

@en

Epoxy-asphalt (EA) attracted the attention of road authorities in many countries as a solution for open-graded porous surface layers with enhanced durability and longevity. This research presents an experimental programme to assess the durability of epoxy-modified open-graded porous asphalt (EMOGPA) mixes, emphasising the effects of the reactivity of two mineral fillers on mixes containing various EA proportions. Results indicate that the EMOGPA mixes have shown a high sensitivity to the conditioning time before compaction (aka. preconditioning). The materials produced exclusively by EA are the most sensitive to preconditioning, reducing their water and ravelling resistance with increased preconditioning time lengths. The number of gyrations has also been proven as an efficient quantity of the compaction effort required to reach the target mix properties. Moreover, the proportional increase of EA in mixes led to substantially improved durability. Hydrated lime in epoxy-modified asphalt mixes also affected their mechanical response. The indirect tensile strength and toughness of EA mixes were higher than other mixes, while mixes with limestones were stronger and tougher than those with hydrated lime. This attribute reflects the positive contribution of apolar fillers to strengthen and toughen the EA mixes.@en

Epoxy asphalt attracted the attention of road authorities in many countries as a solution for du-rable open-graded porous asphalt (OGPA) surface layers with enhanced longevity. Nevertheless, the recycla-bility of aged epoxy asphalt materials has not been thoroughly studied yet. This research presents an experi-mental program conducted in the laboratory to assess the potential recyclability of epoxy-modified open-graded porous asphalt (EMOGPA) mixes. Results indicate that the aging increased the tensile strength of studied mixes, with the strength and strength development rate of aging EMOGPA mixes to be almost identi-cal to standard OGPA mixes. The EMOGPA mixes have shown higher resistance against water damage than the OGPA mixes supporting the claim that the stone-mastic adhesion is improved with the use of epoxy bind-er. It was also proven that the aged material containing the epoxy binder could be re-melted to produce new pavement materials. The new EMOGPA mixes with the recycled epoxy material exhibited similar durability characteristics with the recycled standard OGPA mixes.@en

The proper disposal of steel slag has always been a great challenge for the metallurgical industry in China and around the world. In this work, the steel slag aggregate (SSA) was surface pretreated (PSSA) and applied into asphalt mixture. The adhesive behavior between the bitumen and five different types of aggregates (i.e., limestone, diorite, diabase, SSA, PSSA) were evaluated based on the contact angle and binder bond strength tests. The pavement performance of three asphalt mixtures which contain normal aggregate, SSA and PSSA respectively, was analyzed by Marshall stability test, wheel-tracking rutting test, low-temperature bending creep test and water sensitivity test. The results showed that surface modification can improve the surface properties of SSA, reduce its contact angle with bitumen, and eventually lead to the improvement of adhesion between them. In addition to the satisfied low-temperature properties, PSSA was found to significantly improve the anti-rutting property and reduce the water sensitivity of asphalt mixture. This work is expected to promote an alternative application for recycling of SSA in pavement engineering.@en

Moisture in bitumen and at the bitumen-aggregate interface affects the cohesive and adhesive properties of asphalt mixtures, which are critical for the service performance and durability of pavements. This paper aims to investigate the kinetics and thermodynamics of moisture transport in bitumen at various temperatures and relative humidity for different bitumen types. Transport models are introduced to study the moisture transport mechanisms. A parameter optimization approach combined with the finite element method is applied to simulate moisture transport behavior. Results show salient sorption increase at higher relative humidity levels (more than 70%), indicating the occurrence of clustering of water molecules in bitumen, which can lead to a significant decrease of the diffusion coefficient. Transport models show great quality in simulating experimental results, in which the S-Cluster model provides a detailed explanation of the moisture transport mechanisms and describes better the performance at high sorption levels. The diffusion coefficient, cluster size and activation energy were determined and were found to be linked to the bitumen chemical and structural properties. The transport kinetics and thermodynamics are expected to contribute to a comprehensive understanding of moisture transport behavior in bitumen and further of pavement moisture damage at complex and interacting environmental conditions.

@en

Bitumen in asphalt pavements reacts slowly with atmospheric oxygen, resulting in oxidative ageing. This oxidative reaction is strongly dependent on the physical diffusion of the oxygen into the bitumen. This study aims to use molecular dynamics (MD) simulation to investigate the oxygen diffusion into the bitumen film and analyse the effects of anti-ageing compounds (AACs) on the oxygen diffusion. The MD diffusion simulations using a Polymer Consistent Force Field (PCFF) were conducted on a bitumen-air bi-layer model at different temperatures. Fick's second law was used to calculate the diffusion coefficient of the oxygen in the bitumen film. It is found that the oxygen diffusion coefficients ranged from 6.67 × 10⁻¹⁰ to 7.45 × 10⁻¹¹ m²/s for the unmodified and AAC-modified bitumens at the simulating temperatures of 25, 50 and 100 °C. Irganox acid and DLTDP (Dilauryl thiodipropionate):furfural showed two different anti-aging mechanisms, i.e., reducing the oxygen physical diffusion and controlling the chemical oxidative reaction. Reducing the oxygen diffusivity by constructing a network in the bitumen to retard oxygen diffusion and increase the transport path is an efficient way to slow down the bitumen aging without the antioxidant consumption. This work proposed a MD-based computational approach, contributing to 1) determination of the oxygen diffusion coefficient of the existing bitumen that is extremely challenging for the experimental measurement and 2) instruction of developing new antioxidant.

@en

This study aimed to explore the long-term aging influence on chemo rheological properties and develop novel consecutive models for the long-term aging reaction kinetics of bitumen. The results revealed that the aging index was significantly dependent on the types of selected parameters. The Zero-order model was suitable to describe the long-term aging reaction kinetics of bitumen based on the oxygen containing functional groups with the reaction rate constants in 0.7–3.3*10−4 (mol L−1·h−1). In the SARA-based consecutive reaction model, the most optimum kinetics model for aromatic fraction was the Third-order reaction model and the corresponding reaction kinetics constant (k1) was 0.02 (mol·L−1)−2(h)−1. The Zero-order model could well fit the generation kinetics of asphaltene molecules with the reaction rate constant k2 of 3.85*10−4 mol·(L·h)−1. Further, the transformation reaction from the resin to asphaltene molecules was the control step of the whole consecutive reaction model. In this study, when one-unit resin fraction was generated, the consumption amount of aromatic fraction was about 2.82 units. Meanwhile, when one-unit resin fraction was consumed, only 0.58-unit asphaltene could be generated. The developed reaction kinetics models could be beneficial to predict the functional groups distribution and SARA fractions in aged bitumen with different aging degrees.@en

The Guide for Design of Pavement Structures (AASHTO 86/93) and Mechanistic Empirical Pavement Design Guide (MEPDG) are two common methods to design continuously reinforced concrete pavement (CRCP) published by the American Association of State Highway and Transportation Officials (AASHTO) in the USA. The AASHTO 86/93 is based on empirical equations to assess the performance of highway pavements under moving loads with known magnitude and frequency derived from experiments on AASHTO road tests. The MEPDG is a pavement design method based on engineering mechanics and numerical models for analysis. It functions by incorporating additional attributes such as environment, material properties, and vehicle axle load to predict pavement performance and degradation at the selected reliability level over the intended performance period. In order to evaluate the CRCP design procedure and performance, crack width (CW) and crack spacing (CS) from five examined test tracks in Europe with different climate condition, base layer, geometry, and materials were collected in this paper and compared with predicted distresses as well as CW and CS from AASHTO 86/93 and MEPDG design methods. The results show that the interactions between geometrics, material properties, traffic, and environmental conditions in the MEPDG method are more pronounced than in the AASHTO 86/93 and the prediction of CS and CW based on MEPDG matched closely with the recorded data from sections@en

Lignin, one of the most abundant natural polymers, has been extensively studied as an additive in bituminous binders. Even though the lignin improves the overall resistance against oxidative aging of bitumen, it could lead to high thermal cracking sensitivity. In this study, a bio-oil (i.e., rapeseed oil) is implemented in lignin-modified bitumen to ameliorate characteristics, such as the resistance to fatigue and cracking. The long-term aging of bitumens formulated by different proportions of bio-oil was simulated by the pressure aging vessel (PAV) method. Fourier Transform Infrared Spectroscopic (FTIR) results demonstrated lignin has a remarkable antiaging effect, but adding bio-oil will slightly deteriorate the antiaging effect. The Brookfield rotational viscometer showed that the addition of bio-oil was able to reduce the binder’s viscosity observably, thereby improving the workability of bitumen. The frequency sweep tests revealed that lignin increased the stiffness and improved the thermal stability. Also, the multiple stress creep recovery tests corroborated that lignin significantly enhanced the rutting resistance of binders. The fatigue and thermal cracking properties of lignin-modified binder could be strengthened by increasing bio-oil content which is confirmed from both linear amplitude sweep, Glover-Rowe parameter, and Bending Beam Rheometer (BBR) tests. Moreover, the relaxation test results demonstrated that bio-oil decreased the residual stress ratio and relaxation time dramatically. Overall, this study has shown preliminary conclusions on the incorporating of bio-oil to enhance the medium-low temperature properties of lignin-modified binders. In the meantime, bio-oil did not interfere with the improvement influence of lignin on the neat bitumen regarding high-temperature performance.@en

Pavement materials containing epoxy-asphalt are mainly used to enhance the fatigue cracking resistance of surfacing layers on bridges. These materials have also been proposed for roadways, but limited field data are available. In this research, a fully instrumented epoxy-modified asphalt surfacing layer was applied to measure strain responses in service conditions. Results over the first-year monitoring period indicated that the epoxy-modified asphalt behaves fundamentally similarly to a reference one with an asphalt mix of the same aggregate gradation. The epoxy-modified asphalt demonstrated the lowest transverse compressive strains at decreased temperatures, reflecting the potentially high material resistance against thermal cracking. After the summer period, the modified material showed lower tensile strains than the reference mix compared with the previous time period. Such an attribute could indicate the ongoing curing-induced stiffening of epoxy-modified asphalt at high temperatures during summer. The longitudinal and transverse strain measurements had inverse tendencies at all temperatures. Finally, the mechanical response of the studied materials after the summer has been examined using a classical fatigue cracking model and following a life cycle assessment methodology, and preliminary findings support the use of epoxy-asphalt for sustainable pavements.@en

Asphalt aging often leads to rapid degradation of road performance, which seriously affects the service life of asphalt pavement. Exploring the influence of asphalt oil sources, asphalt grades, and filler types on asphalt microcharacteristics in the asphalt aging process can provide an essential reference to guide asphalt pavement maintenance. In this study, we selected seven kinds of asphalt and three fillers commonly used in China for research. The pressurized aging vessel (PAV) and homemade ultraviolet (UV) aging equipment were used to perform thermo-oxidative aging and UV aging tests, respectively, of asphalt. The microcharacteristics of asphalt before and after aging were analyzed via attenuated total reflectance fourier transformation infrared spectroscopy and nuclear magnetic resonance ¹H spectroscopy. The results show that the oil source of asphalt exerted the most significant influence on the microcharacteristics of the aged asphalt, while the effect of the asphalt grade was relatively limited. The addition of fillers did not affect the aging mechanism of asphalt. UV and PAV aging generated apparent differences in the changes in the aged asphalt microstructure.

@en

In this study, a series of viscosity tests were performed to investigate various conditions, i.e. temperature, shear rate and dilution level, on the curing behavior of epoxy bitumen. The results show that curing rate of epoxy bitumen increased with temperature; high shear rate would interfere the formation of crosslinks in epoxy bitumen, resulting in a negative effect on curing rate; diluting epoxy bitumen by a base bitumen was an effective way to control the curing rate and reduce the material cost. Considering the workability and durability of paving materials, it is recommended that dilution level of epoxy bitumen is 25%, mixing rate is 20 r/min, curing temperature is 130 ℃, and the pavement construction should be finished within 5 hours.

@en