Circular Image

J.M.C. Mol

info

Please Note

220 records found

Journal article (2026) - Yiran Li, Lingwei Ma, Zongbao Li, Xin Guo, Jingzhi Yang, Jinke Wang, Arjan Mol, Dawei Zhang
Surface stabilization treatment serves as a primary method to promote stable rust layer formation on weathering steel (WS). However, due to the complex and multicomponent chemical formulations of stabilization treatment agents (STA), the precise control over STA component ratios to achieve the best stabilization treatment effect remains highly challenging. This study combines high-throughput experiment and machine learning method to establish an optimization framework for designing rust layer STA formulation. By employing high-throughput droplet dispensing experiments and wire beam electrode electrochemical testing, a predictive model is constructed using the AdaBoost algorithm. Interpretability analysis is further integrated to guide Bayesian optimization for iterative formulation refinement. After two optimization cycles, the optimal STA formulation (0.70 g/L CuSO4, 0.20 g/L MgSO4, 0.60 g/L Na2HPO4, and 0.20 g/L tannic acid) is identified from over 2.8 million candidate formulations. The optimized STA promotes the generation of stable rust layer on Q420 WS, which effectively reduces rust layer defects, inhibits corrosive medium penetration, and significantly enhances the corrosion resistance of WS. ...
Molybdenum disulfide (MoS 2) has emerged as a promising electrocatalyst for the electrochemical reduction of CO 2, primarily yielding carbon monoxide. However, product selectivity is known to be highly sensitive to structural features such as edge termination and defect density. In this work, we report the formation of higher hydrocarbons (C 2+ products) enabled by the presence of inherent sulfur vacancies in MoS 2 when combined with various ionic liquids as co-catalysts. While MoS 2 has traditionally shown limited hydrocarbon output, our findings demonstrate for the first time that native defect sites, interacting synergistically with the electrolyte environment, can facilitate the production of significant amounts of C 2+ species. These results provide new insights into defect-mediated catalytic pathways and highlight the importance of electrolyte design in tuning product distribution during CO 2 electroreduction. ...
Journal article (2026) - Durga S. Nair, Reshma S. Babu, Prasad Gonugunta, Thamayanthi Panneerselvam, Harish Kumar, Ruud Hendrikx, Arjan Cornet, Arjan Mol, Prasaanth Ravi Anusuyadevi, More Authors
The surging demand for high-energy density lithium-ion batteries (LIBs) necessitates the exploration of anode materials with higher storage capacity. Nickel‑cobalt (Ni-Co) based transition metal oxides (TMOs) are strong contenders due to their high theoretical capacity based on conversion reactions. The copper (Cu) doping strategy is adopted to improve the electrochemical performance through addressing the drawbacks of NiCo2O4, such as lower conductivity and volume expansion. In this work, Cu-doped NiCo2O4 nanomaterials are synthesized via a rapid, efficient, and scalable microwave-assisted synthesis route. When evaluated as an anode material for LIBs, the Cu-doped NiCo2O4 electrode delivers a high reversible specific capacity of 662 mAh g−1 at a current density of 100 mAg−1. The enhanced performance is attributed to the unique porous nanorod-like structure with a high surface area of 59.4 m2/g, which provides short lithium-ion diffusion pathways. Significantly, the copper acts as an inactive material that accommodates volume changes effectively during cycling when compared to pure NiCo2O4. Furthermore, the electrode exhibits an excellent rate capability and remarkable cycling stability. These findings indicate that copper doping is found to be an efficient approach for enhancing the cyclic performance of TMO-based anodes for next-generation LIBs. ...
Journal article (2026) - R. Addai, S. Ramamurthy, D. Zagidulin, Z. Wang, C. Power, J. M.C. Mol, Y. S. Hedberg
De-icing road salts are widely employed for snow and ice mitigation in cold climate regions, with sodium chloride (NaCl) being the most commonly used salt. The extensive application of NaCl has raised significant infrastructure, sustainability, and environmental concerns, and it has led to the emergence of various alternative de-icing salts, including other chloride-based and organic salts and compounds. In this study, the effect of zinc and acetate species on the corrosion behaviour of steels was systematically investigated using a combination of atmospheric corrosion testing, immersion testing, electrochemical measurements, cross-sectional microscopy, Zn K-edge X-ray absorption spectroscopy (XANES), and thermodynamic speciation modelling. The effect of eight chloride and non-chloride salts and their mixtures on the corrosion of structurally important galvanized steel, mild steel, and high-strength steel was studied. The chloride-based salts were found to be more detrimental than the organic salts to the corrosion of mild and high-strength steels, but all the salts were similarly corrosive to galvanized steel. It was found that the presence of both zinc and acetate species significantly enhanced corrosion and the Fe dissolution rate in steels. >40 wt.% of the 20 µm-thick galvanized zinc layer was dissolved after one week of immersion in 0.5 M sodium chloride or sodium acetate. After this one-week immersion, or the 10-week atmospheric field exposure, any remaining zinc was entirely in the form of zinc oxide. Our findings call for further investigation before using organic de-icing salts, alone or in mixtures with NaCl, on galvanized steel. ...

Rethinking volta potential in nowadays and future in-situ kelvin probe studies

Journal article (2026) - Ehsan Rahimi, Patrick Mesquida, Thilo Glatzel, Yaiza Gonzalez Garcia, Arjan Mol
The Volta potential (also known as contact potential) is widely used in Kelvin probe studies of corrosion, energy materials, and biomaterials, but its relation to electrochemical behavior in solution, and its possible interpretation as an electrochemical signal, remains debated and is often inconsistent. Here, we clarify the conditions under which the electrostatic contrast revealed by Kelvin probe measurements can be meaningfully correlated with redox-related behavior, and when such interpretation is not valid. We also argue for terminology that is consistent with physical theory, interfacial chemistry, and recent methodological advances such as alternating current Kelvin probe force microscopy (AC-KPFM) and open-loop electric potential microscopy (OL-EPM). ...
Highlights

• Controlled pretreatments link steel oxide chemistry to epoxy adhesion.
• Adhesion strength scales with surface hydroxyl density.
• Hydroxyl-rich surfaces show superior adhesion retention in saline environments.
• Probe molecule links microscopic amine bonding to macroscopic adhesion strength.
• Covalent coupling across silane–steel interface linked to superior adhesion strength. ...
Seagoing vessels operate in harsh environments which make them especially prone to progressive degradation mechanisms such as fatigue and corrosion. Acoustic emission (AE) monitoring is gaining interest from ship operators and inspectors for its potential as an early-warning structural health monitoring technique for these types of damage. A major challenge facing the implementation of AE is dealing with the background noise. This article presents an experimental study of ultrasonic noise levels in representative environments and conditions AE monitoring. The probability of detection (PoD) is proposed as a quantitative metric for the detection of damage in the presence of operational noise. Measurements were carried out in multiple locations on board of a vessel under different operational conditions. Measurements at cruising speed on hull plates inside the engine room suggest that the ultrasonic background noise level exceeded 90 dB under 100 kHz but rapidly reduced in the higher frequencies associated with the failure mode-related AE signals. The PoD was estimated to be 94% for damage signals above 100 kHz. These results suggest that acoustic emission monitoring has the potential to perform reliably under noisy conditions. This perspective is promising to the future of a structural health monitoring system based on AE measurement. ...
Corrosion is a leading damage mechanism in the degradation of marine assets. Organic barrier coatings are widely used as a corrosion mitigation measure, because their application suppresses the interaction between the metallic structure and the corrosive environment. Electrochemical impedance spectroscopy (EIS) is a well-established technique for the evaluation of coating performance. Acoustic emission (AE) monitoring has gained increasing interest as a technique for continuous monitoring of corrosion damage. In this experimental study, EIS measurements are combined with AE monitoring to investigate the degradation of different organic barrier coatings. Laboratory experiments were performed on 7 aluminum specimens covered with different types of coatings. Water uptake was achieved by immersing the samples in a salt solution for 24 hours prior to each test. Each sample was equipped with an electrochemical cell (Ag/AgCl reference electrode, platinum mesh counter electrode, acidic NaCl solution; pH=2) and an AE sensor (85-180kHz). The acidic salt solution was used to accelerate the degradation of the coatings for a period of 24 hours during which periodic EIS measurements were performed as well as continuous AE monitoring. AE signals detected during the test could be associated with a measured reduction in coating resistance and, in some cases, visible signs of surface degradation. The preliminary results from the study indicate that coating degradation generates AE signals in the same frequency range as that of typical AE from corrosion degradation. This is a promising perspective towards expanding the capabilities of AE based structural health monitoring systems. ...
Journal article (2026) - Bharath Chandran, Reshma S. Babu, Arjan Mol, N. Satyanarayana, Prasaanth Ravi Anusuyadevi, Durga S. Nair, O. Padmaraj, Prasad Gonugunta, Thamayanthi Panneerselvam, R. Murugan, Gangineni Ramesh Babu, Ruud Hendrikx, Peyman Taheri
In recent years, spinel-structured transition-metal oxide ZnMn2O4 has attracted attention as a low-cost anode material with high lithium-ion storage capacity. However, its practical application is limited by poor intrinsic electrical conductivity, sluggish reaction kinetics, and large volume changes during repeated lithiation and delithiation, leading to unstable cycling behavior. Although several strategies have been explored to improve cyclic stability, many reported systems still suffer from limited rate performance, multistep synthesis routes, and an incomplete understanding of nitrogen-doped graphene oxide (N-rGO)-induced interfacial effects. In this work, hybrid ZnMn2O4/N-rGO nanocomposites with controlled graphene oxide additions of 20 and 30 wt% were synthesized via a simple one-pot hydrothermal route, enabling intimate oxide–N-rGO interfacial contact. Structural, microscopic, and X-ray photoelectron spectroscopy analyses confirmed the formation of phase-pure tetragonal ZnMn2O4 nanoparticles uniformly distributed on the N-rGO framework. XPS revealed a redistribution of nitrogen bonding configurations at higher GO loading, with increased graphitic nitrogen contribution that may enhance electronic conductivity, while pyridinic and pyrrolic nitrogen species provide interfacial active sites. Brunauer-Emmett-Teller analysis showed that increasing GO content enhanced the specific surface area and pore volume while preserving mesoporous architecture. The ZnMn2O4/N-rGO nanocomposite containing 30 wt% graphene oxide (ZMO-30) delivered a reversible discharge capacity of 859.02 mAh g-1 after 100 cycles at 100 mA g-1 with superior rate performance and reduced charge-transfer resistance, demonstrating the beneficial role of oxide–N-rGO interfacial engineering in improving the kinetics and durability of ZnMn2O4 anodes. ...
Journal article (2026) - A. J. Cornet, A. M. Homborg, L. ‘t Hoen-Velterop, J. M.C. Mol
Developing accelerated exposure tests that accurately predict the in-service performance of structural aircraft coatings remains challenging, largely due to the complexity of simulating real-world environmental conditions without altering key degradation mechanisms. This study evaluated four different coating systems under various accelerated exposure tests and compared their degradation behavior to in-service performance. Coating degradation was characterized using electrochemical impedance spectroscopy, scanning electron microscopy, and attenuated total reflectance Fourier transform infrared spectroscopy. Under in-service conditions, failure was primarily driven by the leaching of corrosion inhibitors, while the polymer matrix degraded predominantly through hydrolysis and thermo-oxidation. In contrast, during outdoor- or cyclic salt spray exposure, inhibitor leaching remained a key contributor to coating degradation although polymer degradation was mainly caused by ultraviolet radiation or hydrolysis. These findings emphasize the challenge of replicating real-world degradation in laboratory settings. Additionally, anodized oxide layers containing polymers within their pores played a critical role in maintaining protection during early coating failure. Chromate-based systems restored barrier properties, likely through chromate adsorption on hydrolyzed products within the oxide pores. In comparison, praseodymium-based systems failed to restore protection, while lithium-based systems sustained protection through an intact polymer. ...
Journal article (2026) - Bharath Chandran, Reshma S. Babu, Arjan Mol, N. Satyanarayana, Prasaanth Ravi Anusuyadevi, Durga S. Nair, O. Padmaraj, Prasad Gonugunta, Thamayanthi Panneerselvam, R. Murugan, Gangineni Ramesh Babu, Ruud Hendrikx, Peyman Taheri
Spinel ZnMn2O4 is a promising anode material for lithium-ion batteries owing to its high theoretical capacity, low cost, and environmental compatibility. However, its practical utilization is limited by poor electrical conductivity, sluggish reaction kinetics, and structural instability during repeated lithiation and delithiation. These limitations motivate the development of an interfacial strategy that can simultaneously improve charge transport and mitigate the structural degradation associated with conversion-type lithium storage. In this work, N-doped reduced graphene oxide (N-rGO) is intimately wrapped around porous ZnMn2O4 nanoparticles to construct an interconnected oxide–graphene interface. The N-rGO framework provides continuous electronic pathways and stable interfacial transport channels, while its flexible network helps accommodate volume variations and maintain electrical connectivity during cycling. The resulting ZMO-M/N-rGO nanocomposite exhibits improved electrochemical kinetics and high-rate capability compared with pristine ZMO-M, delivering a reversible discharge capacity of 541.09 mA h g−1 at a current density of 2 A g−1. Following an initial 10-cycle activation period, the nanocomposite maintains a stable electrochemical response for 300 cycles at 1 A g−1, retaining a discharge capacity of 619.10 mA h g−1, whereas pristine ZMO-M exhibits pronounced capacity fluctuations. Electrochemical impedance analysis further reveals lower interfacial resistance and a more gradual, controlled evolution of Li+ transport behavior in the nanocomposite. These results demonstrate that N-rGO interfacial wrapping is an effective approach for improving charge-transfer kinetics, maintaining stable transport pathways, and enhancing the long-term electrochemical stability of ZnMn2O4-based anodes. ...
Journal article (2026) - Jiaqi Li, Jia Lu, Derek R. Lovley, Yongqiang Fan, Feng Li, Xiangying Meng, Arjan Mol, Fuhui Wang, Tingyue Gu, Upadrasta Ramamurty, Dake Xu
Passive metals protected by surface oxide films dominate modern structural materials. Thus, understanding the mechanisms governing passive film breakdown is essential. The electronically insulating TiO2 passive film on titanium separates the underlying Ti0 from environmental oxidants, but microbial biofilms have been reported to catalyze titanium corrosion. Here we demonstrate that the common marine microbe Shewanella algae growing on titanium reduces TiO2 to destabilize the passive film. The biofilm consumes oxygen, generating anaerobic conditions near the metal interface even when the bulk environment remains aerobic. High-resolution characterizations reveal thinning of the passive layer and accumulation of lower-valence titanium oxides. Electrochemical analyses show a 6-fold increase in corrosion current from Ti0 accompanied by enhanced pitting. Mutant studies and other approaches indicate that extracellular flavins function as an intermediary electron carrier for S. algae TiO2 reduction. These results demonstrate how microbes create localized microenvironments that accelerate corrosion of otherwise highly corrosion-resistant metals. ...
Journal article (2026) - Keer Zhang, Arjan Mol, Yaiza Gonzalez-Garcia
Understanding localized corrosion under atmospheric droplets is critical, yet previous studies have mostly focused on single-droplet systems or general trends, leaving the role of individual droplets within multi-droplet environments yet to be explored. Here, we present a fully automated, image-based, data-driven framework for analyzing corrosion progression under thousands of droplets simultaneously. Using time-resolved optical imaging and pre-trained large vision models for droplet segmentation, we construct per-droplet color features and propose a probability-based representation of corrosion product formation in inner and outer regions of interest. This approach overcomes the limitations of binary classification by capturing the continuous and spatially heterogeneous nature of corrosion product formation. Applied to carbon steel exposed to over 1500 pre-sprayed 1 M NaCl droplets of various sizes, the method reveals that the probability of corrosion product presence strongly depends on droplet size, with larger droplets more likely to exhibit products both under and around the droplet footprint. Moreover, corrosion products in the outer region can appear independently of under-droplet corrosion, suggesting a role for inter-droplet interactions. By transforming raw imaging data into physically meaningful per-droplet metrics, this work offers a scalable platform for investigating localized corrosion kinetics and morphology in complex, real-world droplet populations, opening new opportunities for connecting droplet formation and population behavior to local and overall atmospheric corrosion rates. ...
The increasing concentration of CO2 is a serious concern for the environment. Electrochemical conversion of CO2 into valuable products, including fuels, offers a viable solution and helps close the carbon-neutral cycle. Metal-organic framework (MOF) composites, due to their high porosity, large surface area, and significant chemical tunability, are considered to be a promising class of catalyst materials for the CO2 reduction reaction (CO2RR). This chapter focuses on the fundamentals of CO2RR and mechanism of the reaction followed by discussing the recent advancements in MOF composite electrocatalysts for CO2RR including MOF-supported electrocatalysts, conductive-supported MOF composites, graphene and carbonous MOF composites, MOF-MXenes, MOF-polymers, and polyoxometalate. ...
Journal article (2025) - Marlon Mopon, Arjan Mol, Santiago J. Garcia
This study demonstrates that galvanically coupling AA2024-T3 and AA7075-T6 affects localized corrosion even with the alloys’ comparable electrochemical behaviour. In situ reflected light microscopy tracked corrosion initiation and trench propagation, while zero resistance ammeter measurements quantified galvanic current density and potential. This combined approach allowed direct correlation between electrochemical signals and optically detectable surface phenomena. Galvanic coupling increased cathodic activity at AA2024-T3 intermetallic particles (IMPs) and caused the surrounding matrix to dissolve more extensively beyond the trench that formed around the particles. Local activity analysis revealed initial IMP dealloying was unaffected by galvanic coupling. However, lateral growth of trenches in both alloys was accelerated under coupling compared with electrically-isolated conditions. Correlation of optical activity with electrochemical measurements showed that trends and fluctuations in galvanic current and potential reflect different stages of local corrosion, facilitating the morphological and physicochemical interpretation of the electrochemical data. ...
Corrosion is a leading damage mechanisms in the degradation of marine assets. Acoustic emission (AE) monitoring has gained increasing interest as a technique for continuous monitoring of corrosion damage. This study numerically and experimentally investigates the feasibility of wall thickness loss estimation from the AE signals due to localized corrosion. The interaction of the elastic waves emitted due to the evolution of corrosion damage are influenced by the local thickness and material properties of the structure. A steel plate of (500 mm x 500 mm x 10 mm) with a localized wall thickness loss between 0 and 80% in the center of the plate was considered. The numerical investigation was conducted using a higher-order finite element model. Laboratory experiments were performed on a carbon steel specimen instrumented with 7 AE transducers (40 - 250 kHz). Corrosion damage was artificially introduced in the steel plate by progressively milling a pit in the center. At different stages of wall thickness loss, simulated AE sources were generated. The response of the structure was evaluated based on signal characteristics such as amplitude, rise-time, frequency content, and waveform. A correlation between the signal amplitudes and the wall thickness loss was observed in both experimental and numerical results. This perspective is promising for the feasibility of corrosion-induced wall thickness loss estimation based on AE measurements. ...

Integrating high-throughput experiments and interpretable machine learning approach

Journal article (2025) - Jingzhi Yang, Junsen Zhao, Xin Guo, Yami Ran, Zhongheng Fu, Hongchang Qian, Lingwei Ma, Patrick Keil, Arjan Mol, Dawei Zhang
The discovery of synergistic strategies effectively improves the corrosion inhibition capability of amino acids. However, the wide variety of amino acid formulations and the time-consuming nature of corrosion tests make combinatorial discovery challenging to achieve. Herein, a library of 70 amino acids was created and tested in a high-throughput manner. Benefiting from a vast amount of labeled data of amino acid formulations, an interpretable machine learning approach was used to reveal the contribution of molecular features to inhibition performance of amino acids and the synergisms in the optimal formulation. The synergism was verified by electrochemical tests and quantum chemical calculations. ...
Review (2025) - Anthony E. Hughes, Christopher D. Easton, Prasaanth Ravi Anusuyadevi, Thomas J. Raeber, Nick C. Wilson, Arjan Mol
XPS analysis is routinely used in corrosion studies to analyse corrosion product and protective layers on a range of metals. In the case of transition metals and especially iron, the extraction of information about chemical species including identification and quantification requires complex fitting of the metal 2p spectrum. Unfortunately, there is extensive misunderstanding of what is required for fitting of these metal 2p photoelectron peaks. In the case of high spin Fe 2p compounds there is a complex structure based on multiplet and satellite peaks which is often ignored. In this review of the application of XPS in the study of corrosion and protection of ferrous metals; we quantify the extent of misinterpretation of XPS Fe 2p spectra within the literature. It is found that in over 70 % of papers there is an adamant misunderstanding of the requirements for fitting Fe 2p, which can be divided into three groups. First, in the most serious case, there seems to be a lack of understanding of spin orbit coupling which gives rise to the major Fe 2p3/2 and Fe 2p1/2 peaks with the latter being incorrectly assigned to a different chemical species. Second, satellite structures are often assigned to a different chemical species. Third, single peaks are used to fit chemical components whereas a complex multiplet structure should be employed. We establish the extent to which these errors are made by critical appraisal of over 220 papers published in selected years between 2015 and 2024. ...
Journal article (2025) - A. J. Cornet, A. M. Homborg, L. ’t Hoen-Velterop, J. M.C. Mol
Eliminating hexavalent chromium-based corrosion inhibitors from structural aircraft coatings remains a significant challenge, primarily due to the lack of reliable accelerated test methods. This study evaluates the performance of various structural aircraft coatings under different exposure conditions, i.e. outdoor exposure, cyclic salt spray testing and in-service conditions, supplemented by environmental sensors. Quarterly inspections and scanning electron microscopy were used to evaluate corrosion damage. The findings highlight a lack of correlation between accelerated testing and outdoor exposure testing, likely driven by disparities in salt deposition, UV-radiation, time of wetness and temperature cycling. Additionally, galvanic couples between skin and fasteners remain difficult to protect, with chromate-based systems offering limited inhibition and alternative systems struggling to protect such complex assemblies. However, in lap-joints, alternative coatings outperformed chromate-based counterparts, likely due to their polymer matrices providing improved barrier properties, hence limiting access of electrolyte to the coating-aluminium alloy interface. ...

Enhanced stability through partial dealloying and prolonged exposure

Journal article (2025) - Marlon Mopon, Arjan Mol, Santiago J. Garcia
The stability of inhibiting layers on AA2024-T3 intermetallic particles (IMPs) during re-immersion in saline following an initial immersion in a Ce(III)-containing electrolyte was investigated using in situ reflected light microscopy. Re-immersion behaviour varied due to differences in IMP composition, spatial distribution, and Ce(III) precipitation. IMPs were grouped into four categories based on whether their activity was high or low during both the immersion and re-immersion stages. Majority of the high activity particles during re-immersion had low activity during immersion. Longer immersion times (up to 72 h) and a brief delay in inhibitor supply (30 s) reduced re-immersion activity by increasing Ce(III) coverage. These findings suggest that corrosion protection systems promoting greater Ce(III) precipitation may enhance re-immersion stability. ...