State-of-the-art intracortical neural recording and stimulation systems rely on subdural implants tethered to a cranial implant which itself has a wireless power and data link to the outside world [1] (Fig. 6.2.1). However, this tethered configuration poses challenges such as scarring and potential damage to the surrounding tissue due to strain and micromotions, making this approach unsuitable for chronical implants [2]. Consequently, there is growing interest in wireless connections between cranial and subdural implants. This paper focuses on wireless powering between implants, traversing the dura and cerebrospinal fluid (CSF) tissue layers over distances of 0.5 to 1cm (transdural powering). With modern burr-hole craniotomy, the hole drilled in the skull is 6mm in diameter, limiting the available size for the TX. Moreover, the power dissipation of the TX must be low to keep tissue heating below 1°C [3]. RF and optical modalities suffer from higher attenuation in tissue compared to ultrasound (0.6dB/cm/MHz) [4]. Furthermore, for transdural powering, power losses from reflections at medium interfaces (e.g., skull) are avoided, making ultrasound (US) a prime candidate for efficient in-body wireless power transfer. US is also preferable to inductive powering since US beam steering up to large angles (>45°) is needed to maximize power delivery and compensate for brain micromotions of up to ±4mm [5] and misalignment during surgery. However, prior art US driving systems either use single-phase transducer driving [6, 7], incapable of beam steering, or use class D drivers with low power transfer efficiency (PTE) [8, 9]. A phased array with increased driving efficiency was presented in [10], but it cannot perform beam steering without grating lobes that can be eliminated with miniature transducers with a pitch close to λ/2. To facilitate direct integration between CMOS and the transducer array, the CMOS driving units should also be pitch matched [8, 9].

A near-field galvanic coupled transdural telemetry ASICs for intracortical brain-computer interfaces is presented. The proposed design features a two channels transmitter and three channels receiver (2TX-3RX) topology, which introduces spatial diversity to effectively mitigate misalignments (both lateral and rotational) between the brain and the skull and recovers the path loss by 13 dB when the RX is in the worst-case blind spot. This spatial diversity also allows the presented telemetry to support the spatial division multiplexing required for a high-capacity multi-implant distributed network. It achieves a signal-to-interference ratio of 12 dB, even with the adjacent interference node placed only 8 mm away from the desired link. While consuming only 0.33 mW for each channel, the presented RX achieves a wide bandwidth of 360 MHz and a low input referred noise of 13.21 nV/√Hz. The presented telemetry achieves a 270 Mbps data rate with a BER < 10 ^-6 and an energy efficiency of 3.4 pJ/b and 3.7 pJ/b, respectively. The core footprint of the TX and RX modules is only 100 and 52 mm ², respectively, minimizing the invasiveness of the surgery. The proposed transdural telemetry system has been characterized ex-vivo with a 7-mm thick porcine tissue.

This paper presents a 1.8-2.7 GHz low-power ring-oscillator-based fractional-N injection-locked digital PLL (IL-DPLL) in 40-nm CMOS for Internet-of-Things clock generation. A two-path injection technique is proposed to improve the in-band phase noise and the integrated jitter of the implemented PLL by 6 dB and 1.8×, respectively. Furthermore, a digital foreground calibration is introduced to effectively reduce reference spurs in a short calibration time of 2 μs. In the worst-case channel, the proposed DPLL using a 64 MHz reference input shows a 1.6 ps integrated jitter, -43.6 dBc reference spur, -45.8 dBc fractional spur and 1 kHz frequency resolution while consuming 1.33 mW power.