Coastal regions have experienced significant environmental changes and increased vulnerability to floods caused by the combined effect of multiple flood drivers such as storm surge, heavy rainfall and river discharge, i.e., compound floods. Hence, for a sustainable development of coastal cities, it is necessary to understand the spatiotemporal dynamics and future trends of compound flood hazard. While the statistical dependence between flood drivers, i.e., rainfall and storm surges, has been extensively studied, the sensitivity of the inundated areas to the relative timing of a driver's individual peaks is less understood and location dependent. To fill this gap, here we propose a framework combining a statistical dependence model for compound event definition and a hydrodynamic model to assess inundation maps of compound flooding from storm surge and rainfall during typhoon season in Shanghai. First, we determine the severity of the joint design event, i.e., peak surge and precipitation, based on the copula model. Second, we use the same frequency amplification (SFA) method to transform the design event values in hourly time series so that they represent boundary conditions to force hydrodynamic models. Third, we assess the sensitivity of inundation maps to the time lag between storm surge peak and rainfall. Finally, we define flood zones based on the primary flood driver, and we delineate flood zones under the worst compound flood scenario. The study highlights that the temporal delay between storm surge and rainfall plays a pivotal role in shaping the dynamics of flooding events. More specifically, that the peak rainfall occurs 2 h before the peak storm surge would cause the deepest average cumulative inundation depth. At the same time, the results show that in Shanghai surge is the primary flood driver. High storm surge at the eastern part of the city (Wusongkou tidal gauge) propagates upstream in the Huangpu River, resulting in fluvial flooding in Shanghai city center and several surrounding districts. This calls for a better fluvial flooding control system hinging on the backwater effect during high surge in the upper and middle Huangpu River and in the newly added urbanized areas to ensure flood resilience. The proposed framework is useful to evaluate and predict flood hazard in coastal cities, and the results can provide guidance for urban disaster prevention and mitigation.@en

Marine biofouling is a major concern in the operational performance of submerged floating tunnels (SFTs). The objective of this research is to extend hydrodynamic conditions in experiments and numerically investigate the effects of marine fouling on the hydrodynamic behavior of SFTs, including flow characteristics and forces on the SFT subject to waves. A sensitivity analysis of roughness parameters including different roughness heights and roughness coverage ratios is carried out. Additionally, the hydrodynamic forces of a roughened SFT with a circular shape and a newly designed parametric shape are compared.

@en

This research investigates the dynamic response of offshore wind turbine (OWT) systems subject to ice-structure-soil interaction (ISSI). To simulate the behavior of level ice sheets, a coupled approach involving the cohesive element method (CEM) and the finite element method (FEM) is applied. For soil-structure interaction (SSI), the Mohr–Coulomb (M-C) model is employed to accommodate glacial soils. A three-dimensional model for ice-OWT-soil interactions is established using LS-DYNA, focusing on the North American Great Lakes region. The impact of factors, including conical structure geometry, ice loading conditions, and soil characteristics, on the actions of ice and the displacement of the OWT structure, is systematically assessed. The results show a notable reduction in horizontal ice forces when a conical structure is used, underscoring its potential to enhance the stability of an OWT. Additionally, lower ice loading height results in increased ice force and reduced structural displacement. Furthermore, variations in soil properties, specifically elastic shear modulus, cohesion and angle of internal friction, exert a significant influence on OWT dynamics. The elastic shear modulus of glacial soils impacts the displacement of the OWT structure, posing a threat to structural stability. In addition, reduced cohesion and friction angle contribute to greater structural displacement.

@en

Analyzing the spatial-temporal changes in tropical cyclone (TC) tracks in the east China coastal ocean (ECCO) to quantify the magnitude of poleward and landward migration of TCs is of significant importance for coastal disaster mitigation and planning due to its susceptibility to the impacts of TCs. In this study, the TCs that affected the ECCO from 1949 to 2022 are classified into three typical types of tracks using the k-means clustering method, mass moments, and track interpolation based on TC location, shape, and intensity information. Type 1 is a northwestward track, Type 2 is a northwest to northeast-turning track, and Type 3 is a northwest to northeast-turning offshore track. Type 1 tracks mainly make landfall in southern China, while Type 2 predominantly makes landfall in eastern China. Moreover, the proportion of Type 1 decreases while their landfall percentage increases over time, and the proportion of Type 2 tracks is increasing. The probability of TC effects on the eastern and northern parts of the ECCO is increasing, and the boundary where the TC center reaches after landfall is shifting landward. During the period from 1994 to 2022, there has been a significant migration in TC tracks, with the mean centroid of the TCs affecting the ECCO shifting westward by 0.66° in longitude and northward by 1.26° in latitude, which means the magnitude of the poleward shift is about twice that of the landward shift. This migration appears to have been pre-conditioned by a combined influence of a weakening westward steering flow, reduced vertical wind shear, and warmer sea surface temperature Our findings provide valuable insights into the longitudinal and latitudinal migration of TC tracks and have important implications for disaster prevention, mitigation planning, and the adjustment of crucial coastal protection zones in the ECCO and similar regions around the globe.

@en

The July 2021 flood heavily affected many inhabitants, buildings and critical infrastructure throughout Germany, Belgium and the Netherlands. Specifically, the Ahr Valley (Germany) showcased the destructive power associated with these extreme events. Hence, this region was the focus of a field survey, aiming at describing the flood-induced damage to buildings and assessing the possible underlying processes that led to structural failures. The field assessment revealed a close connection between building failures and (1) local flow depths and velocities, (2) building location, (3) distance from the riverbank and (4) construction type. Although it is difficult to identify the exact causes that induced failures, the detailed assessment revealed that damages mainly originated from local scour and hydraulic loads, often unevenly distributed around buildings. Importantly, many buildings were significantly affected by (large) floating debris impacts and damming, both responsible for additional loads, highlighting their importance in flood-resistant building design. Furthermore, data showed that buildings near the riverbanks and in the upstream part of villages were more severely damaged. Altogether, data provide a better understanding of the flood processes that lead to building failures, fostering future research towards the development of safer protection measures and more effective flood risk management strategies.

@en

The design of coastal and hydraulic structures must account for extreme conditions, such as wave overtopping, and consider variables that may not be relevant under normal circumstances to ensure safety. This research investigates the characteristics of air cavity pressure and cavity water depth beside an overflowed vertical caisson breakwater, focusing on the influence of flow conditions and hydraulic parameters for a slowly varying, surging-type tsunami. A physical model was used to conduct controlled experiments, enabling the study to explore various scenarios, including subcritical and supercritical downstream flows with varying downstream flume outlet heights and different upstream water depths. Dimensionless equations for air cavity pressure and cavity water depth were derived through multivariate regression analysis, providing a systematic approach to analyze their behaviors under different flow conditions. The results show that air cavity pressure is significantly influenced by the presence of air in the cavity, with a transition from fully ventilated to partially or non-ventilated conditions as the upstream water depth increases. Cavity water depth is observed to be deeper in the non-ventilated case, aligning with previous studies. The derived dimensionless equations demonstrate strong correlations, offering valuable tools for predicting air cavity pressure and cavity water depth under various scenarios, contributing to the design and analysis of hydraulic structures. This study provides insights into wave-structure interactions, extreme wave loads, and the dynamic responses of coastal infrastructures under wave-induced conditions. Overall, this research advances our understanding of air cavity pressure and cavity water depth behaviors, providing essential data for optimizing the design, performance, and safety of hydraulic and marine structures in response to complex ocean wave loads.

@en

This study investigates the dynamics of air-water flow and the resulting forces on a broad-crested weir with a vertical face under both ventilated and non-ventilated cavity conditions. The focus is on measured forces and flow characteristics across various upstream water depths and flume outlet heights, categorized by distinct groups based on flow regimes. The experimental setup incorporates measurements of air-water mixture density, air cavity pressure, cavity water depth, and velocity profiles in the recirculation pool downstream of the weir. Results indicate that under supercritical downstream flow conditions, the forces exerted on the weir are directly proportional to the upstream water depth, while the downstream flume depth has a minimal impact. Conversely, in subcritical downstream conditions, the downstream flume depth significantly influences stabilizing forces due to increased cavity water depth. Additionally, pressure profile estimations on the downstream-facing wall of the weir using hydrostatic, Bernoulli, and Navier-Stokes equations show that the hydrostatic assumption is inadequate for estimating pressures and sliding forces in non-ventilated cavities. This study offers crucial insights into air-water flow dynamics in weirs, underscoring the importance of incorporating dynamic factors into weir design and hydraulic modeling.@en

Background: The share of renewable energy feeding the European grid has been growing over the years, even though the intermittency of some renewable energy sources can induce electric grid instability. Energy storage has proven to be an effective way of reducing grid instability. Various solutions for large-scale energy storage are being researched nowadays. This study focusses on the innovative low-head pumped hydro storage (LH PHS) technology, a large-scale energy storage scheme suitable for shallow seas (5 – 30 m depth). Implementation of renewable energy technologies, such as wind farms in Europe, Asia and North America, has faced public opposition which has delayed or even cancelled the implementation of renewable energy projects. Literature about public perception of projects highlights the importance of involving stakeholders from the early stages of project planning. Considering this, the present study aims to collect stakeholder opinions (via an online survey) to determine what is necessary for a smooth implementation of LH PHS in the North Sea, both from technical and policy points of view. Results: Stakeholders from commercial parties, government authorities and local groups recognized the potential of LH PHS as a means to increase the share of renewable energies within the European power grid. Economics, bureaucratic burden, and structural safety have emerged as primary aspects of concern respecting the implementation of LH PHS. The impression of the respondents is that a low-head pumped hydro station would not have negative effects on their organizations. Furthermore, most of the engineering firms participating in the study communicated that their knowledge and resources could be involved in the construction of such an energy storage facility. Conclusion: As identified stakeholder concerns such as economics and structural safety are currently being researched, effective communication of the findings of this research is paramount to keep stakeholders informed of the ongoing progress. Two-way communication between researchers and stakeholders is recommended to enhance public acceptance of future technologies. Furthermore, is it advisable to undertake an examination of the available energy policies relevant to LH PHS.

@en

Marine biofouling is a major concern in the operational performance of submerged floating tunnels (SFTs). The objective of this research is to investigate the effects of marine fouling (represented by surface roughness) on the hydrodynamic behavior of SFTs, including the hydrodynamic forces on the SFT subject to current-only, wave-only, and combined current-wave flow conditions. The effects of increased surface roughness induced by marine fouling on the dynamic response of an SFT are characterized by hydrodynamic force coefficients, including drag and inertia coefficients. At the Water Lab of Delft University of Technology (TU Delft), experiments have been performed in a wave-current flume to compare the SFTs’ behaviors as affected by different roughness characteristics. In addition, a parametric cross-section for an SFT is presented, and the hydrodynamic performance associated with surface roughness effects on the parametric shape and circular SFT cross-section shape are compared. The results show that the parametric shape can effectively reduce the drag coefficient (C_d) under current-only conditions and lower the inertia coefficient (C_m) when waves are present. As roughness height and coverage ratio increase, C_d generally increases while C_m decreases. However, small differences in C_d and C_m can be observed with regard to roughness parameters for wave-only conditions. The Morison coefficients adapted for a marine-fouled SFT measured in the experiments are compared to predictions from engineering standards and are recommended for engineering practice.

@en

Fish screens are structures associated with pump stations and power plants, that prevent entrainment of fish, but may also be a source of physiological stress, if placed in locations of strong flow speeds that fish are unable to sustain swimming against over time. Herein, the acute response of Anguilla anguilla and Oncorhynchus mykiss to a 30-minute exposure to two water flow regimes was evaluated at the lowest level of the hypothalamus–pituitary–interrenal axis, from blood serum and skin mucus, in a controlled setup presenting a 45° vertically-angled fish screen. Cortisol response was species specific, regardless of the matrix employed. While the flow velocity factor did not describe any variance of eel data, and no statistically significant differences in cortisol concentrations were observed among eel groups, cortisol release in response to flume hydraulics followed a dose-dependent pattern in trout, with a large proportion of the variance described by the model. Mucus cortisol was highly and strongly correlated to serum levels of trout specimens subjected to the strongest flow. Given the established neuromodulatory and molecular roles of cortisol on major fitness-relevant processes, animal welfare implications may be severe, especially considering ever increasing exposure to chronic anthropogenic stressors, resulting in repeated and/or prolonged elevation of circulating glucocorticoids.

@en

Early initial impoundment can generate additional revenue but bring more flood risk in late-stage construction diversion. In view of the possible flood risk and catastrophic consequences caused by high dam failures induced by early impoundment, a comprehensive assessment is proposed. Taking the Lianghekou high rockfill dam on the Yalong River, southwest China, as an example, this study established the late-stage diversion risk model and predicted the failure probabilities for the original, 15 days ahead, and 30 days ahead schemes varied with the initial impoundment time using the Monte Carlo method. Then, considering overtopping-induced gradual breaking of rockfill dams, the NWS dam-break flood forecasting model (DAMBRK) was used to estimate the break development and the outflow hydrograph. Due to no significant differences being found in the outflow hydrographs of the three schemes, life loss was used an index for the consequences of inundation. Combining the failure probability, life loss, and early impoundment revenues brought by earlier power generation, a satisfied initial impoundment scheme was acquired using the multi-objective decision model. The results revealed this method can find a reasonable initial impoundment time in view of the late-stage diversion risk assessment.

@en

The modelling of complex free surface flows is challenging due to the mobility and deformability of the interface and air entrainment characteristics, which are highly affected by turbulence. With the framework of Reynolds averaged Navier–Stokes (RANS) models and the volume of fluid (VOF) method, turbulence quantities at the air–water interface tend to be over-estimated. In this study, interfacial turbulence treatment methods including the buoyancy modification model based on the simple gradient diffusion hypothesis (SGDH) and Egorov’s turbulence damping model are investigated. Furthermore, due to the unconditionally unstable characteristics of the standard k-ε turbulence model, the stabilized k-ε turbulence model is applied as a comparison. The turbulence attenuation performance using different interfacial turbulence treatment methods in the vicinity of the interface is compared and discussed for stratified flows and free overflow weirs for aerated and non-aerated nappe scenarios. The turbulence quantities and free surface profile under different flow conditions are validated against experimental data and an analytical model. The results show that for free surface waves, both the SGDH model and the turbulence damping model give strong improvements in turbulence production compared with the standard k-ε model. The SGDH model augments the turbulence kinetic energy (TKE) in the unstable stratification, leading to unphysical behaviour for the partially dispersed and separated flow.

@en

Extreme surges and rainfall represent major driving factors for compound flooding in estuary regions along the Chinese coast. The combined effect of extreme surges and rainfall (that is, compound floods) might lead to greater impacts than if the drivers occurred in isolation. Hence, understanding the frequency and severity of compound flooding is important for improving flood hazard assessment and compound flood resilience in coastal cities. In this study, we examined the dependence between extreme surges and corresponding rainfall events in 26 catchments along the Chinese coastline during typhoon and non-typhoon seasons using copula functions, to identify where the two drivers more often occur together and the implication for flood management in these locations. We found that the interaction between flood drivers is statistically significant in 10 catchments located around Hainan Island (south) and Shanghai, where surge peaks occur mainly during the typhoon season and around the Bohai Sea (north), where surge peaks occur mainly during the non-typhoon season. We further applied the copula-based framework to model the dependence between surge peaks and associated rainfall and estimate their joint and conditional probability in two specific locations—Hainan Island and the Bohai Sea, where the correlation between flood drivers is statistically significant. We observed that in Hainan Island where most of the surge peaks occur during the typhoon season, extreme rainfall events during the typhoon season are generally more intense compared to annual maxima rainfall. In contrast, around the Bohai Sea where surge peaks occur mainly outside the typhoon season, rainfall is less intense than annual maxima rainfall. These results show that the interaction between extreme surges and rainfall can provide valuable insight when designing coastal and urban infrastructure, especially in highly populated urban areas prone to both coastal and pluvial flooding, such as many Chinese coastal cities.

@en

Hurricane Ike, which struck the United States in September 2008, was the ninth most expensive hurricane in terms of damages. It caused nearly USD 30 billion in damage after making landfall on the Bolivar Peninsula, Texas. We used the Delft3d-FM/SWAN hydrodynamic and spectral wave model to simulate the storm surge inundation around Galveston Bay during Hurricane Ike. Damage curves were established through the relationship between eight hydrodynamic parameters (water depth, flow velocity, unit discharge, flow momentum flux, significant wave height, wave energy flux, total water depth (flow depth plus wave height), and total (flow plus wave) force) simulated by the model and National Flood Insurance Program (NFIP) insurance damage data. The NFIP insurance database contains a large amount of building damage data, building stories, and elevation, as well as other information from the Ike event. We found that the damage curves are sensitive to the model grid resolution, building elevation, and the number of stories. We also found that the resulting damage functions are steeper than those developed for residential structures in many other locations.

@en

The effects of surface roughness as induced by marine fouling on the hydrodynamic forces on a submerged floating tunnel (SFT) are experimentally and numerically investigated in detail at Reynolds numbers Re = 8.125 × 10³–5.25 × 10⁴. A sensitivity analysis to different roughness parameters including roughness height, skewness, coverage ratio, and spatial arrangement is performed. In addition, an optimized parametric cross-section for an SFT is proposed, and the hydrodynamic performance of the parametric shape and circular SFT cross-section shape with roughness elements is compared. The pressure distribution along the SFT, flow separation and wake characteristics are analyzed to provide a systematic insight into the fundamental mechanism relating the roughness parameters and flow around an SFT. In order to better understand the nonlinear relationships among structural geometry, roughness parameters, flow states, and structural response, an artificial intelligence method using Random Forest (RF) for feature importance ranking is applied. The results show that with the parametric shape, the hydrodynamic forces on the fouled SFT can be effectively mitigated. The roughness height and coverage ratio affect the equivalent blockage and hence, change flow separation and recirculation length in the wake. Lower skewness of the roughness elements can increase the critical Re by changing the relative roughness parameter. Horizontal arrangement of the roughness elements on an SFT generally results in the largest hydrodynamic forces, compared to staggered and vertical distributions. Throughout the feature importance ranking, the flow regime is found to be the most important feature of the hydrodynamics of the SFT. In addition, the SFT cross-section shape and roughness coverage ratio play a dominant role.

@en

Due to the environmental crisis, there is a need for a more conscious and integrating design process within the field of urban infrastructure development. Through cooperation between civil engineering and spatial design resilience of the built environment can be increased. Delft University of Technology investigates interdisciplinary design as a method and incorporates this into its MSc-level education of students in the faculties of civil engineering and architecture. The focus of the research was on the reconstruction projects after disasters like hurricanes and tsunamis. By way of surveys of the participating students, the effectiveness of the interdisciplinary design methods used, and the interpretation of the terms multidisciplinary and interdisciplinary are revealed. From survey results about understanding of multidisciplinary and interdisciplinary it can be concluded that interdisciplinary design should entail a conscious and orchestrated process in which the disciplines present their ideas within a shared value system before systematic integration. The challenges are at personal and cognitive levels, an open attitude is necessary to be able to perceive and react, process and understand, retrieve information. Only then decisions on - and production of - appropriate responses come out of co-creation between engineering within the spatial design process.

@en

The energy transition requires large-scale storage to provide long-term supply and short-term grid stability. Though pumped hydro storage is widely used for this purpose, regions without natural topography do not have the potential for traditional high-head pumped hydro storage. To address this, multiple projects for low-head and seawater pumped hydro storage have been proposed, though few have been implemented. Here, we review the state of the art of the components of low-head seawater pumped hydro storage projects, for construction in shallow seas or integrated into coastal defenses. We reference all civil infrastructure components, in addition to legal, environmental/biological, and financial constraints, drawing knowledge from proposed, planned, and constructed tidal power and seawater pumped hydro storage projects worldwide. Combining this knowledge, we make a preliminary evaluation of the feasibility for low-head seawater pumped hydro storage in the North Sea. We find that an elevated storage basin is more economical than an excavated one in shallow bathymetry (10 m deep or less), while the reverse is true in deeper water. Corrosion and fouling prevention are already well developed due to implementation of these measures at tidal power plants. Dam construction is feasible if measures are taken to address piping, macro-instability (primarily from rapid drawdown), and bursting of the clay layer. Within the context of Europe, legal and environmental regulations may be the most formidable hurdles to such projects.

@en

The Meuse river in the Netherlands has been made navigable by the construction of a cascade of seven low head weirs. Because of environmental regulations, hydropower facilities exist at only two weirs. This implies the full hydropower potential of the Meuse cascade is not utilized. By using pump-turbines the river sections upstream of the weirs could be additionally usable as energy storage reservoirs and could improve and ensure river navigability under changed climate conditions. The main goal of this study is to assess the possible utilization of the full energy storage- and hydropower potential of the Meuse cascade within Dutch environmental regulations. The novelty of this study is the evaluation of the concept of using canalized river sections for pumped-storage purposes within conditions of fluctuating discharge and -water levels throughout the year. In order to meet the goal of the study the relatively fish-friendly Archimedean screw has been selected as pump-turbine. Next a conceptual design of a pumped-storage hydropower plant equipped with screws has been compiled. By using this design, the assessment of utilizing the hydropower- and energy storage potential of the cascade has been carried out by constructing and applying a numerical model. The study shows it is possible to utilize the full hydropower- and the majority of the energy storage potential of the Meuse cascade. The cumulative installed turbine capacity for the cascade turns out to be 81 MW. The Annual Energy Yield (AEY) from regular hydropower alone is 225 GWh. In addition, the yearly surplus power that can be processed for energy storage purposes is 137.2 GWh, of which 77.2 GWh is returned to the grid by a round-trip efficiency of 56.25 %. In total 302.2 GWh can be delivered to the grid which can power up to 75.000 households. The specific cost is relatively high: roughly 15,000 euro/kW. The method developed here can be applied to evaluate the storage- and hydropower potential of other canalized rivers as well, such as the upper Mississippi.@en

To counteract a potential reduction in grid stability caused by a rapidly growing share of intermittent renewable energy sources within our electrical grids, large scale deployment of energy storage will become indispensable. Pumped hydro storage is widely regarded as the most cost-effective option for this. However, its application is traditionally limited to certain topographic features. Expanding its operating range to low-head scenarios could unlock the potential of widespread deployment in regions where so far it has not yet been feasible. This review aims at giving a multi-disciplinary insight on technologies that are applicable for low-head (2-30 m) pumped hydro storage, in terms of design, grid integration, control, and modelling. A general overview and the historical development of pumped hydro storage are presented and trends for further innovation and a shift towards application in low-head scenarios are identified. Key drivers for future deployment and the technological and economic challenges to do so are discussed. Based on these challenges, technologies in the field of pumped hydro storage are reviewed and specifically analysed regarding their fitness for low-head application. This is done for pump and turbine design and configuration, electric machines and control, as well as modelling. Further aspects regarding grid integration are discussed. Among conventional machines, it is found that, for high-flow low-head application, axial flow pump-turbines with variable speed drives are the most suitable. Machines such as Archimedes screws, counter-rotating and rotary positive displacement reversible pump-turbines have potential to emerge as innovative solutions. Coupled axial flux permanent magnet synchronous motor-generators are the most promising electric machines. To ensure grid stability, grid-forming control alongside bulk energy storage with capabilities of providing synthetic inertia next to other ancillary services are required.

@en

Many coastlines around the world are protected by dikes with shallow foreshores (e.g. salt marshes and mudflats) that attenuate storm waves and are expected to reduce the likelihood and volume of waves overtopping the dikes behind them. However, most of the studies to date that assessed their effectiveness have excluded the influence of infragravity (IG) waves, which often dominate in shallow water. Here, we propose a modular and adaptable framework to estimate the probability of coastal dike failure by overtopping waves (Pf). The influence of IG waves on overtopping is included using an empirical approach, which is first validated against observations made during two recent storms (2015 and 2017). The framework is then applied to compare the Pf values of the dikes along the Dutch Wadden Sea coast with and without the influence of IG waves. Findings show that including IG waves results in 1.1 to 1.6 times higher Pf values, suggesting that safety is overestimated when they are neglected. This increase is attributed to the influence of the IG waves on the design wave period and, to a lesser extent, the wave height at the dike toe. The spatial variation in this effect, observed for the case considered, highlights its dependence on local conditions – with IG waves showing greater influence at locations with larger offshore waves, such as those behind tidal inlets, and shallower water depths. Finally, the change in Pf due to the IG waves varied significantly depending on the empirical wave overtopping model selected, emphasizing the importance of tools developed specifically for shallow foreshore environments.@en