Both preloaded and injected bolted connections are commonly used in steel bridges in The Netherlands. Where preloaded bolted connections are already used for a longer time, the injection of bolt holes is a method used from the 1970s onwards. Injection of bolts became a good alternative for the replacement of riveted connections. This injection increases the slip resistance of the connection by filling the clearance between the bolt and the plate. Combining both methods increases the slip resistance of a bolted connection and is therefore even more beneficial.
According to the standard NEN-EN1993-1-8 [17], it is safe to assume that the resistance of a preloaded and injected bolted connection is equal to the sum of the two individual obtained resistances from preloading and injection. The aim of this research is to validate this statement and thus investigate the resistance of a slip-critical steel-to-steel connection including preloading and/or injection.

The study addresses this manner through both experiments and numerical analysis, addressing all three types of connections. In addition, this potential of summation is considered for two different levels of preloading, implementing plastic and elastic preload preloading. These levels of preloading were considered for two reasons, embodying different applications and identifying the effect of the preload force on the resistance. Each experiment is based on a short-term testing method that is in compliance with the described method of the EN1090-2. These resistances are verified by a numerical analysis with the goal of gaining more insight into the behaviour of the connection and validation of the obtained results.

From both experimental and numerical results, it is concluded that a summation of the individual resistances overestimates the actual resistance of a preloaded and injected bolted connection when measuring at the edge of the plates. This overestimation is similar for both preload levels.
Based on these results, it is concluded that it is unsafe to assume that the resistance of a preloaded and injected bolted connection is equal to the sum of the individual resistances obtained from preloading and injection. However, this conclusion might change if a different criterion for measuring relative displacements at specific locations is implemented.

The resistance of a connection is defined at a fixed magnitude of relative displacement measured at the edge of the plate, assuming that this is representing the displacement of the bolt. However, it turned out that the assumed limit displacement of 0.15mm did not result in the same displacement at the bolt(group) for all connections due to the amount of preload force and the geometry of the plates. Therefore, it is recommended to investigate the sensibility of the measured displacements for different geometries of and preload levels in the connection.

Sustainability concerns steer the construction sector towards adopting a circular economy philosophy. Steel-concrete composite beams are extensively used in multi-story buildings and bridges due to their competitive construction and efficient material use. Currently the composite action is mainly achieved by headed shear connectors welded to the top flange of the beam, obstructing the non-destructive demountability. Demountable shear connectors can be used in order to open up the composite con-struction for reusability. Demountable shear connectors can take the form of a bolted connection which requires a tight control of construction tolerances. This thesis is fo-cused on studying a bolt coupler connector which is seen as a valuable alternative to the more conventional embedded bolt. The proposed shear connector consists of a bolt and coupler embedded in prefabricated concrete decks which are connected through the top flange of the steel section by an injection bolt.
Full-scale experiments have been performed to investigate the feasibility of construc-tion of a demountable car park. The demountable flooring was obtained by large pre-fabricated concrete decks in combination with tapered beams. Experimental research has confirmed the possibility of assembly and disassembly of the system if construction tolerances are appropriately designed. The most influential factors were quantified based on experimental observations, measurements and finite element models. The hole clearance should be designed keeping in mind the deformability of the system during construction, the manufacturing tolerances and the speed of construction. Experiments show that resin injection can be reliably and labour efficiently used for large oversized holes which allow for higher fabrication imperfections and reduced construction while at the same time enabling composite action of the connectors under live load.
The reusability of the structure was confirmed by a set of eight four-point bending tests considering uniform and non-uniform connector arrangements. Finite element models closely match the experimental results in terms of deflection, stresses and curva-ture. However, the end slip is overpredicted which is in line with research performed by other authors. The efficiency of the non-uniform connector arrangements was studied experimentally and numerically to reduce the construction costs. Concentrating the shear connectors toward the supports will bring the highest benefit in terms of beam bending stiffness without the need of a large number of connectors to prevent uplift.
An extensive cost analysis was performed based on a database of 15500 beam solu-tions generated by a design algorithm develop as part of this thesis. The case study provides a preliminary cost assessment of two demountable steel-concrete composite floorings in order to quantify their economic viability. It was shown that the system constructed with prefabricated solid slabs is more viable compared to the demountable profiled sheeting slab. The most influential contribution to the final cost of the struc-ture comes from the steel work and the labour intensive manufacturing.