Flow sensing exists widely in nature to help animals perform certain tasks. It has also been widely adopted in engineering applications with different types of sensing instrumentation. In particular, in the field of aerospace engineering, airflow sensing is crucial to vehicle state evaluation and flight control. This project surveys the key mechanisms from biological features in nature that enable flow sensing and expands towards the application motivation to identify a suitable airflow sensor that can be equipped to a flapping wing micro air vehicle (FWMAV) for onboard airflow sensing.

The selection of sensors is first narrowed down to three major types of airflow sensors from the state of art that have the most potential to be integrated onboard a flapping wing MAV, considering the sensor performance need, size, weight and power (SWaP) restrictions. Two thermal-based commercially available low-cost airflow sensors RevP and RevC from Modern Device have been selected after the trade-off analysis.

A full workflow of calibrating and evaluating the two airflow sensors' directional sensitivity has been carried out through two wind tunnel campaigns. Their performance under grid-generated turbulence is compared with a constant temperature hot-wire anemometer. This series of tests leads to the conclusion that the RevP airflow sensor has better performance and is therefore chosen to be placed onboard a flapping wing MAV Delfly Nimble.

Both mounted tests and tethered hovering tests with the Delfly Nimble are performed to further examine the airflow sensor RevP's measurement performance under different influence factors such as MAV throttle levels, MAV body pitch angles and freestream speeds. In the end, it is concluded that as a proof of concept, the RevP sensor is capable of performing effective measurements for low flow speeds less than 4 m/s, within the pitching angle range of -30 to 30 degrees. Although this is the first achieved tethered hover flight with onboard airflow sensing for a flapping wing MAV, its limited payload and onboard power supply demands an even smaller and less power consuming design of airflow sensors to enable further applications such as autonomous reactive control under wind disturbances.

Flapping wing micro air vehicles (FWMAV's) are a subcategory of unmanned aerial vehicle which use flapping wings for thrust generation. The high agility and maneuverability of FWMAV's are very favorable attributes, making them more applicable in cluttered spaces. A tailless FWMAV called the Delfly Nimble has been developed at the Delft University of Technology. Due to the inherent instability of the tailless design an active controller is required to ensure safe and stable flight of the drone. In previous research, models have been developed for the longitudinal dynamics of the Delfly Nimble. In this paper, a grey-box state-space model of the lateral body dynamics in hover conditions is identified using system identification techniques. The parameters which needed to be estimated were stability and control derivatives, and they were obtained with a least-squares approach. Free-flight experiments were performed to generate the identification and validation data. A doublet train was used in the identification experiments, with the gains of the controller adjusted in such a way that maximum excitation was acquired. The identified model has been validated with various maneuvers. These included doublets, 112-maneuvers, maneuvers using coupled inputs, and maneuvers with sideways flight. The resulting model is able to predict the state derivatives of most maneuver accurately, reaching accuracies of over 90% for maneuvers close to hover. Moreover, in closed-loop configuration it is able to simulate the state response accurately, with accuracies of over 85% for maneuvers close to hover, and remains stable, making it applicable for controller design and stability analysis. Finally, based on the model the inherent instability of the lateral body dynamics was also confirmed, for there are eigenvalues with positive real parts.

This study investigates the wing deformation of the flapping-wing micro air vehicle (MAV) DelFly II in various flight configurations. Experiments were carried out with the MAV tethered in a windtunnel test section. To determine the best suited measurement approach, a trade-off study was carried out which showed that a point tracking approach with background illumination is most suitable. The therefore used high-speed camera pair and illumination were mounted on the same rotating frame with the DelFly, which allowed adequate viewing axes of the wings at for all pitch angles. Processing was done a purpose-build algorithm, allowing 136 points per wing to be measured simultaneously with an average lost point ratio of 3.4 % and an estimated accuracy of 0.25 mm. Results of hovering flight show some previously unnoticed behaviors. First, it was noted that the upper and lower wing on each side do not deform purely symmetric but show some considerable asymmetric behavior like heave and camber production. Furthermore, the upper wing shows a torsional wave and recoil behavior at faster flapping frequencies, which was shown to be beneficial in insect flight. Lastly, it was found that an air-buffer remains present between the wing surfaces at all times of the clap-and-peel motion (apart from the root trailing edge). This air-buffer increases once freestream velocity is added, which is investigated during the climbing flight study. Here, the reduced angle of attack of the wing is assumed to reduce the wing loading at faster climb, resulting in lower deformations outside the clap-and-peel motion. The isolated effect of a body pitch angle is also studied. Here, the asymmetrical freestream direction results in larger asymmetries such as wing alignment with the freestream direction and reduced camber and even camber reversal during the upstroke. In forward flight the pitch angle is changed simultaneously with the flapping frequency and freestream velocity. Due to the non-linear properties the wing deforms not directly as a superposition of the individual effects. Deviations are mostly present in increased asymmetry in incidence angle, while the camber behaves more linear and the clap-and-peel motion also remains relatively unchanged. The torsional wave and recoil are here however reduced. Descending flight was also tested. Velocities below 1m/s result in relatively minor deformation changes, while faster descent leads to large flapping frequency fluctuations, making interpretation of the results impossible.