Over the last 70 years, pultrusion has matured into an industry-leading process when it comes to providing high throughput and automated composite manufacture at a competitive price point. In this paper, we review recent innovations that have advanced pultrusion to a versatile manufacturing technology and thereby allowed composite materials to penetrate markets in, e.g., the automotive, construction, aerospace, and wind turbine industries. We accompany our review with discussions on how pultrusion has enabled new innovations within additive manufacturing and sustainable composite manufacturing, and finally, we provide an outlook and suggestions for where we see the potential for research and new industrial applications of pultrusion technology.

This study presents a detailed material characterization study of a pultrusion specific polyurethane resin system. Firstly, the chemical behaviour was characterized by utilizing differential scanning calorimetry. The cure kinetics was fitted well to an autocatalytic cure kinetics model with Arrhenius temperature dependency. The resin system did not show any inhibition time. Then, the viscosity evolution was observed using a rheometer. From these measurements, the gelation point was estimated from the criterion of cross-over point of storage and loss modulus curves. The corresponding cure degree of gelation point was found to be 0.79 using the cure kinetics model. The complex viscosity evolution through dynamic scans was predicted well with a cure degree and temperature dependent viscosity model. The elastic modulus and glass transition temperature of fully and partially cured samples were measured by means of DMA in tension mode. A five step cure hardening instantaneous linear elastic model was fitted well to a wide range of cure degree values after gelation. Lastly, the fitted material models were employed in a case study of a typical pultrusion process to visualize the effects of pulling speed on the material property evolution.

Process-induced stress and deformation are critical factors when ensuring product quality and structural integrity of composite profiles manufactured using thermoset pultrusion processes. In this paper, we present a new steady-state 3D-Eulerian numerical framework that enables 9–35 times faster computations compared to the current state-of-the-art quasi-static 3D-methods. In addition, we show how process-induced effects from the profile-advancing pulling force and an initial compressive stress state can be modelled. We demonstrate in theoretical parameter studies that the pulling force advances die-detachment and reduces die-swelling, while the initial compressive stress state has the opposite but a more pronounced effect.

Pultruded fiber-reinforced polymer composites are susceptible to microstructural nonuni-formity such as variability in fiber volume fraction (V_f ), which can have a profound effect on process-induced residual stress. Until now, this effect of non-uniform V_f distribution has been hardly addressed in the process models. In the present study, we characterized the V_f distribution and accompanying nonuniformity in a unidirectional fiber-reinforced pultruded profile using optical light microscopy. The identified nonuniformity in V_f was subsequently implemented in a mesoscale thermal–chemical–mechanical process model, developed explicitly for the pultrusion process. In our process model, the constitutive material behavior was defined locally with respect to the corresponding fiber volume fraction value in different-sized representative volume elements. The effect of nonuniformity on the temperature and cure degree evolution, and residual stress was analyzed in depth. The results show that the nonuniformity in fiber volume fraction across the cross-section increased the absolute magnitude of the predicted residual stress, leading to a more scattered residual stress distribution. The observed V_f gradient promotes tensile residual stress at the core and compressive residual stress at the outer regions. Consequently, it is concluded that it is essential to take the effects of nonuniformity in fiber distribution into account for residual stress estimations, and the proposed numerical framework was found to be an efficient tool to study this aspect.

This paper concerns non-isothermal flow in a thermoset resin-injection pultrusion process. Supported by temperature measurements from an industrial pultrusion line and a material characterisation study (curing kinetics, chemorheology, and permeability), the material flow was analysed for the manufacture of a thick glass-fibre profile saturated with a pultrusion-specific polyurethane resin. A central finding is that the heating configuration, together with the strongly convective flow near inlets resulted in phase transitions that were both concave and convex-shaped. This is different from existing literature that commonly describes curing being initiated from die-walls, resulting in the concave phase-transitions.