The uncontrolled inclusion of renewable energy sources in the distribution network causes severe overvoltages. Simultaneously, electrification strategies, such as heat pumps and electric vehicles, increase the peak demand, causing undervoltages. The combination of both phenomena has proven challenging for distributed system operators who are accountable for power quality and accessibility. System operators address those voltage issues with network reinforcements, but such projects are costly and time-consuming. We identified that the cost and qualified workforce availability are the main challenges of premature grid reinforcement. This paper evaluated peak-shaving and power curtailment at the low voltage distribution level as market-based alternatives to provide flexibility using the business model canvas. We identified the main actors that would benefit from peak-shaving and power curtailment at the residential level, their relationships, and the value proposition's challenges. We proposed a business model where residential prosumers receive compensation for supporting the network to prevent the distribution system from surpassing the projected power flows. Both alternatives offer system operators more control over the power flow to ensure power quality while decreasing costs, as fewer or no premature grid reinforcements might be needed. The business opportunity resources are categorized as technical and regulatory, highlighting the latter as the main challenge for the business model. We discussed two residential prosumer case scenarios for the Dutch context, one with a PV system and one with a PV and a heat pump. Our analysis suggests that the business models are technically possible for peak-shaving and power curtailment with existing technologies for the selected target. However, the former requires more complex activities and is limited to a narrower segment, as it requires prosumers with PV, storage and high-load devices, such as heat pumps.@en

The urge to reduce the dependence on natural gas for heating at the residential level has led to the deployment of different fossil fuel-free alternatives. In the Netherlands, two technologies are leading the transition: heat pumps, due to their high COP, and photovoltaic–thermal systems, due to their dual electric-thermal output. However, both represent a challenge for users and grid operators, aside from their stochastic behavior. Heat pumps alone can surpass a typical Dutch house's total energy and power consumption. Photovoltaic–thermal systems, as their only electric homologs, usually have a mismatch between generation and demand, causing energy injections to the grid. From the electric perspective, storage systems are a proven solution to reduce the energy exchange with the distribution network. This paper proposes four multi-carrier energy system configurations for a Dutch household, comprising different combinations of a photovoltaic–thermal system, a battery energy storage, a heat pump, and an underground water tank thermal energy system, providing analytical models for every component (including the thermal losses from the thermal storage to the ground), and the space heating and electrical demands. We determined the components’ compatibility and evaluated the combinations considering their thermal performance, electrical performance, and equivalent CO₂ emissions. The results suggest that using a heat pump combined with a photovoltaic system and a battery provides the best trade-off. The photovoltaic–thermal system alone could not supply the thermal demand required for comfortable space heating nor reach temperatures high enough to charge the thermal storage. Combining the thermal storage with the heat pump allows a certain degree of flexibility for the heat pump activation at the cost of COPs between 0.8 and 1.38 when used to charge the thermal storage, thus increasing energy consumption and equivalent emissions considerably.

@en

In low-voltage distribution networks, the high penetration of renewable energy generators in residential buildings has proven challenging for system operators. In response, the grid operators can reinforce the grid infrastructure or deploy battery energy storage systems throughout the network to compensate for the voltage fluctuations. Alternatively, new energy markets for ancillary services have been proposed to involve the prosumers; however, most are at medium and high voltage levels. This paper investigates, from a cost perspective, what conditions can make it attractive for individual prosumers to participate in a low-voltage ancillary service market, specifically power curtailment and peak shaving. We considered a prosumer with a 2 kWp PV system for both ancillary services, adding a 10 kWh battery for the peak shaving case. Curtailing power to comply with the maximum power exchange with the grid does not create any significant change in the LCoE of the PV system, keeping it near 0.072 €/kWh for permitted return grid powers above 1.25 kW. Scenarios closer to zero-injection increase exponentially the LCoE to 0.222 €/kWh. Using a semi-empirical ageing model, we estimated the degradation of the batteries for the cases with and without providing peak shaving, concluding that doing peak-shaving to avoid demanding more than 1 kW from the grid extends the battery life by up to 320 % while increasing its LCoS only 9.5 % when compared to a zero-consumption scenario due to the reduced depth-of-discharge and number of cycles. The results suggest that power curtailment and peak shaving can be attractive for prosumers, thus creating opportunities for ancillary services business models at the residential scale.@en

In the context of building electrification the operation of distributed energy resources integrating multiple energy carriers poses a significant challenge. Such an operation calls for an energy management system that decides the set-points of the primary control layer in the best way possible. This is done by fulfilling user requirements, minimizing costs, and balancing local generation with energy storage. This last component is what enables building flexibility. This paper presents a novel aging-aware strategy for operating grid-connected buildings that combine multiple energy carriers (heat and electricity), storage devices (electric vehicles, batteries, and thermal storage), and power sources (solar photovoltaics, solar collectors). The novel energy management algorithm presented considers the aging of the batteries to enhance the operational differences between storage technologies, thus making explicit the trade-off between the services provided by the hybrid energy storage system and its degradation. This unlocks grid cost reductions between 20–45 % depending on the season when compared to state-of-the-art solutions.@en

Batteries are one of the main tools to provide the flexibility distribution and transmission systems need due to their increasing dependence on weather conditions. However, environmental and economic factors pose a significant problem. New types of batteries that do not rely on rare earth metals and organic solvents but instead use water and more common ions could be a cost-effective and environmentally safe way to provide energy storage in the future. We studied the performance of sea-salt cells designed as a low-cost, environmentally friendly method to store electricity. We used a constant current charge/discharge test with different currents, from 50 mA to 300 mA, to identify the maximum efficiencies of the cell. Then, we introduced a new strategy to determine the cut-off voltage to discharge the battery, inspired by the maximum power point found in photovoltaics. We used a constant voltage charge to determine the cell’s energy density. However, evidence of side reactions urged us to use constant current charge/discharge tests to identify the battery’s capacity based on the efficiencies drop. Results showed a maximum energy efficiency of 74.6% at 200 mA and a maximum Coulombic efficiency of 88.7% at 300 mA. The cut-off voltage of the cell during discharge should be between 1.4 V and 1.6 V. The energy densities range from 10.1 Wh/kg(6.53 WhL) with an efficiency of 57.5% and 4.18 Wh/kg(2.7 WhL) with an efficiency of 69.8%.@en

The energy transition requires electrical alternatives for domestic heating. Heat pumps are the most common alternatives to gas boilers. However, heat pumps consume a significant amount of electrical power. We simulated an 18-node low voltage network with five buildings with six apartments each to evaluate the effect of deploying heat pumps as part of multi-carrier energy systems at the residential level. We also combined heat pumps with solar collectors and thermal energy storage to quantity whether a more complex system benefits the low-voltage network. Replacing the gas boilers for heat pumps in the majority of the buildings resulted in voltage drops below the limit of the standard EN50160. The voltage drops were significantly improved when we included solar collectors and thermal energy storage in the domestic heating system.@en

Energy storage is vital for a future where energy generation transitions from a fossil fuels-based one to an energy system that relies heavily on clean energy sources such as photovoltaic (PV) solar energy. To foster this transition, engineers and practitioners must have open-access models of PV systems coupled with battery storage systems (BESS). These models are fundamental to quantifying their economic and technical merits during the design phase. This paper contributes in this direction by carefully describing a model that accurately represents the power directions and energy dealings between the PV modules, the battery pack, and the loads. Moreover, the general model can be implemented using two different PV generation methods, the Gaussian model and the meteorological data-based model (MDB). We found that the MDB model is more appropriate for short-term analysis compared to the Gaussian model, while for long-term studies, the Gaussian model is closer to measured data. Moreover, the proposed model can reproduce two different energy management strategies: peak-shaving and maximizing self-consumption, allowing them to be used during PV–BESS sizing stages. Furthermore, the results obtained by the simulation are closed when compared to a real grid-tied PV–BESS, demonstrating the model’s validity.@en

Renewable energy power plants and transport and heating electrification projects are being deployed to enable the replacement of fossil fuels as the primary energy source. This transition encourages distributed generation but makes the grid more weather-dependent, thus reducing its inertia. Simultaneously, electrical network operators face voltage, frequency, and stability challenges at the distribution level. Networks were not designed to manage the stochasticity of renewable energy sources or the congestion caused by the new transport and heating demands. Such challenges are commonly addressed through infrastructure reinforcements. This review studies how energy storage systems with different carriers can provide a collaborative solution involving prosumers as ancillary services providers at the distribution level. We focused on the European urban context; thus, we analyzed renewable energy sources, batteries, supercapacitors, hydrogen fuel cells, thermal energy storage, and electric vehicles. A thorough review of successful implementations proved that including storage in one or more carriers benefits the distribution system operators and the prosumers, from both technical and economic perspectives. We propose a correlation between individual energy storage technologies and the ancillary services they can provide based on their responses to specific grid requirements. Therefore, distribution system operators can address network issues together with the prosumers. Nevertheless, attractive regulatory frameworks and business models are required to motivate prosumers to use their assets to support the grid. Further work is recommended to describe the joint operation of multiple storage technologies as multicarrier systems, focusing on the coupling of electrical and thermal energy storage. Additionally, how ancillary services affect the energy storage system’s aging should be studied.@en

Battery Energy Storage Systems typically procure their primary revenues from regulated energy and ancillary services markets; nonetheless, they have great potential in supporting distribution network operators and their users. This paper evaluates the potential business case of battery storage systems integrating market application and services to a photovoltaic assisted electric vehicle fast-charging station. A mathematical deterministic optimization problem is formulated using mixed-integer linear programming to combine battery storage system operation in the day-ahead and frequency regulation market and the remunerated services offered to the charging station. The technical and economic feasibility of the solution and the applicability of the proposed framework is verified through a case study reflecting an existing photovoltaic assisted charging station in the Netherlands and considering the Dutch energy market framework and prices. The study shows that such battery storage system implementation is economically and technically advantageous for the players involved. The battery storage system can stack additional revenues on top of the market revenues. The charging station benefits from a reduced peak power and a 30% tariff reduction, and the system operator would indirectly benefit from the shaved charging station profile. Furthermore, the analysis shows that providing services to the charging station from the battery storage system does not significantly impact its market-related revenues.@en

Fifth-generation energy networks are combined networks of heat and electricity, that have the ability to generate, distribute, store and share energy between consumers. Knowledge on the dynamic behaviour of the physical phenomena related to energy generation, distribution and storage provides insight into the performance of the system as a whole. A mixed-integer linear algorithm is proposed, implementing a partitioned clustering program for subsequent classification of typical demand, grouping specific days with similar demand profiles together. From this arrangement, the optimal network configuration can be determined using an objective function, minimizing the economic and environmental impact. To validate the optimization results, a simulation of the network was built, which mimics its physical dynamic behaviour, and through which the distribution and storage capabilities of the network can be assessed. Advanced advice on fifth-generation energy networks is presented that can be applied to early-stage network design, reducing costs and emissions, along with data on the implementation of renewable energy technologies and their performance. Additionally, this research provides the foundation for numerical modelling of such energy networks which contributes to future research.@en

This paper discusses the design and optimization of electric vehicles’ fast-charging stations with on-site photovoltaic energy production and a battery energy storage system. Three scenarios, varying the number of chargers, distance from the main grid, and on-site photovoltaic generation potential, are investigated. Such scenarios are benchmarked in investment, operating costs, and grid connection requirements. The addition of a battery storage system is also evaluated to reduce the operating cost and, therefore, boost the system’s economic parameters, such as the net present value, and increase the grid independence.The analysis shows that the addition of the battery system can be effective in both performance metrics, the reduction of the grid connection, which can be reduced up to 80% by the addition of a large size battery, and the increase of the net present value, which can be even doubled with respect to the case when the battery storage system is not installed.@en

Smart MicroGrids (SMGs) can be seen as a promising option when it comes to addressing the urgent need for sustainable transition in electric systems from the current fossil fuel-based centralised system to a low-carbon, renewable-based decentralised system. Unlike previous studies that were restricted to a limited number of actors and only took a mono-disciplinary research approach, this current review adopts a multidisciplinary, socio-technical approach and addresses the factors that have been hindering the development of SMGs and considers how these barriers interact. This study contributes to the body of literature on the development of SMGs by mapping and discerning technical, regulatory, market, social and institutional barriers for different types of actors, including technology providers, consumers, Distributed Generation (DG) providers and system operators, based on information derived from laboratory reports, demonstration pilots, and academic journals. In addition, attention is paid to how these barriers interact based on real-life experimentation. A holistic picture of barriers and their interaction is presented as well as recommendations for future research.@en

Battery Energy Storage Systems (BESSs) are a new asset for Primary Frequency Regulation (PFR), an ancillary service for improving the grid stability. The system operators determine the implementation and remuneration of PFR. However, assessing the revenue stream is not enough to define the business case, as also the components’ lifetime has to be estimated. Previous studies of lifetime estimation for BESSs performing PFR considered only the electrochemical storage, disregarding the power electronics (PE). Nonetheless, researchers have shown the importance of estimating PE wear due to the operation when applied in renewable energy generation and microgrids. This paper presents a lifetime analysis of BESSs providing PFR considering IGBT modules, electrolytic capacitors and electrochemical storage degradation. The lifetime information is used to estimate BESS's Net-Present-Value (NPV), evaluating the benefits of deploying PE-based BESS in the European grid. A comparison between different countries, Germany, the Netherlands, and the U.K., is performed, considering the PFR implementation and remuneration differences. The analysis shows that the BESS management strategy can extend its lifetime and that the component that exhibits the shortest lifetime is the electrochemical storage. The PE components are subject to low wear due to the low power utilization and, therefore, small thermal swings while performing PFR. In conclusion, the provision of PFR by means of BESS has been found to be profitable in all three countries. However, in the Netherlands, the potential NPV has been estimated to be 47% and 76% higher than in Germany and the U.K., respectively.@en

The dynamic behaviour - steady-state and transient - of the DC Microgrids during power disturbance can affect the system’s general performance. A hybrid combination of energy storage devices with slow frequency response, like a Fuel Cell, and with a fast dynamic response, like a Super-Capacitor, provides an improved dynamic response to stabilise DC bus voltage. However, control parameters should be designed based on the preferences of the system. This paper proposes a fuzzy-based controller to determine the Virtual Capacitor Droop controller to achieve the desired transient response. The proposed dynamic control method is validated through MATLAB/Simulink.@en

This paper presents a protection framework for low voltage dc grids, which segments these grids into zones and tiers according to their fault current potential and provided protection. Furthermore, the technology and applications of different protection devices are examined. It is demonstrated that the utilization of fast fault interruption and fault limiting inductors are vital for the protection of low voltage dc grids. Moreover, a design of a solid-state circuit breaker is presented, and this devices is experimentally verified. The experimental results showed that the total time for the detection and interruption of faults can be lower than $1 \mu \mathrm{s}$ with solid-state protection devices.

@en

LCL filters are commonly adopted to attenuate the current harmonics produced by Pulse Width Modulation (PWM) Voltage Source Converters (VSC). Due to the nature of LCL filters, several combinations of L and C can deliver the attenuation required by the standards. The optimal configuration is generally evaluated, considering power density, costs, and filter efficiency. This paper shows that semiconductor efficiency should also be considered as an important design variable. It is shown that the AC ripple across the converter side inductor can reduce, to a certain extent, the overall semiconductor losses, when commercial IGBTs and the respective anti-parallel diodes are used. Reduced losses have benefits in terms of semiconductor module lifetime, chip area and cost reduction, and simplification of cooling requirements. Higher AC ripple, however, negatively affect the filter losses. Nonetheless, inductive components are typically much less critical in terms of losses dissipation and lifetime than semiconductors.@en

Energy Storage Systems (ESSs) are promising solutions for mitigating the technical problems created by high penetration of Distributed Generation (DG) in distribution grids. This paper presents a methodology for the ESS sizing and placement within the distribution networks. Those are found through an optimization routine that considers the impact of the use of storage on voltage regulation and system losses. Several scenarios, varying the load and PV panels power, are investigated. In addition, the impact on the energy storage requirements of a basic residential self-consumption scheme is evaluated. The proposed method has demonstrated to be effective in determining the ESS size in the studied scenarios. Furthermore, the results show that the location that requires the lowest ESS rating does not necessarily offer satisfactory performances in terms of losses reduction and voltage control. Also, the paper shows that by encouraging residential users to self-consume the energy produced by the PV panels installed in their house, the grids ESS requirements can be significantly reduced.@en

This paper discusses a qualitative comparison between Two and Three-Level Voltage Source Converter (VSC) topologies for battery energy storage applications. Three-Level Neutral Point Clamped (NPC) and T-Type circuit topologies are benchmarked versus the state-of-art Two-Level VSC in terms of efficiency and power density considering a 100 kW system. Analytical equations for determining the power losses in the semiconductor modules are given, and the procedure for designing the output LCL filter and the DC-link capacitors is described. The analysis, based on off-the-shelf circuit components, shows that the Three-Level topologies perform better than the Two-Level one in both considered metrics, mainly due to their lower switching losses that allow operating at higher switching frequency without significantly degrading the system efficiency, and, at the same time, increasing the system power density. Additionally, it is found that the T-Type topology shows better performances than the NPC topology at full and high partial loads, being then more suitable for applications that require most of the operation at maximum power.

@en

DC Microgrid with integrated photo-voltaics (PV) and battery storage system is a promising technology for future smart grid applications. This paper compares three battery storage technologies namely: lithium-ion (Li-ion), lead-acid, and vanadium redox flow battery (VRFB) in the residential low-voltage dc grids, to increase the penetration of PV to improve self-sufficiency and grid independence. A multi-objective optimisation method is proposed to visualise the trade-offs between four objective functions: cost of electricity, energy autonomy, peak power reduction, and lifetime capital cost. The method is applied to a near-future scenario, based on a real residential feeder. Pareto fronts of the dominant designs are used to compare different battery technologies for this PV-battery integrated dc microgrid application. Additionally, the results provide insight into the dimensioning the battery, the PV, and the front-end ac-dc converter.@en

Due to the distributed nature of future electrical power systems, decentralized control is essential for these grids. This paper shows that converters that have identical voltage thresholds switch off simultaneously even if some could have remained operational. Therefore, inadequate system and energy utilization can occur when decentralized demand or supply response is utilized. The Grid Sense Multiple Acces (GSMA) algorithm proposed in this paper ensures that, after a change occurs in the system, a subset of the converters remains connected to the grid, without the need of utilizing any form of communication. This is achieved by introducing an exponential backoff time between failed connection attempts. Furthermore, several simulations and experiments are conducted to illustrate and validate the behavior of the GSMA algorithm, showing that it can be applied to dc grids in order to improve system and energy utilization.

@en