ML

Matthijs Langelaar

info

Please Note

106 records found

Recent advancements in metal additive manufacturing (AM) technologies have enabled the precise fabrication of complex designs, promoting integration between topology optimization and AM. However, AM processes like laser powder bed fusion (LPBF) inevitably lead to microstructural defects, including keyhole-induced porosity and lack of fusion porosity. These pores significantly degrade the mechanical strength of printed components. The complexity of the process leads to the generation of random and unpredictable pores, which can vary from part to part even if all process parameters and geometry remain the same. Thus, this study proposes a reliability-based topology optimization framework that incorporates the uncertainty arising from random porosity defects during the AM process in a computationally efficient way. In this study, the probability of pore formation is assumed to increase linearly with distance from the build plate, which serves as a proxy for temperature. Assuming that defects are induced exclusively by overheating, the likelihood of pore formation increases with the temperature rise during the build process. A Monte Carlo approach is used to account for the stochastic pore realizations. To avoid performing a separate FEA for each realization, analytical stress fields around pores are used to augment the stress field obtained from a single FEA per optimization iteration. Adjoint sensitivity analysis is then employed for efficient gradient evaluation. Through 2D numerical examples on regular Cartesian grids, this study demonstrates and evaluates the effectiveness of the proposed approach while accounting for process-dependent stochastic porosity. ...
The pursuit of high-performance structures requires innovative manufacturing approaches that balance multiple competing factors. This work focuses on one such novel approach, named Advanced Tape Laying Additive Manufacturing (ATLAM), that integrates the characteristics of automated tape laying and additive manufacturing. ATLAM supported by a dedicated complementary design tool can provide a unique ability to balance mechanical performance, manufacturing flexibility, and eco-efficiency. To exploit the full potential of ATLAM in manufacturing lightweight sustainable structures, we aim to develop, verify and experimentally validate a computational design tool rooted in topology optimization. We use geometric projection topology optimization framework, and tailor it to accommodate ATLAM’s unique features and constraints. We customize the geometric primitive, the projection & material interpolation schemes and design/manufacturing constraints. Then, based on numerical investigation, we showcase excellent effectiveness and robustness of the proposed approach in optimizing geometry and reinforcement placements and designing stiffer yet manufacturable structures. An environmental impact constraint is incorporated to enable a design choice on sustainability. Finally, we experimentally validate our proposed approach, paving the way for reliable use in real-world applications. ...
Journal article (2026) - Aditya Garde, Henk Hoevers, Roland Den Hartog, Matthijs Langelaar, Just Herder, Luc Voruz, Adam Lassise, Christian Körnig
X-ray interferometry (XRI) is a promising technique for ultra-high resolution X-ray imaging. However, a major limitation of a regular design is the long length of the interferometer, which makes it virtually impossible to fit in a single spacecraft. The Willingale XRI design reduced the length by several orders of magnitude with the introduction of a slatted mirror. We propose to parallelize the interferometer using silicon pore optics (SPO). We show that SPO technology, currently being used to fabricate mirrors for ESA’s upcoming NewAthena space mission, can be used for XRI and benefit by starting at a higher technology readiness level. We provide a detailed design description of Willingale XRI and combine it with SPO along with an optimization approach. Further, we apply the optimization approach for a Willingale’s XRI testbed. The optimized design is checked with a ray optics simulation. Furthermore, we report successful fabrication of a slatted mirror manufacturing prototype. The optimized design and fabrication of a slatted mirror manufacturing prototype will serve as a first step toward building an XRI testbed for the demonstration of X-ray interference fringes that would demonstrate the feasibility of a Willingale type XRI. ...
Conference paper (2026) - Rajit Ranjan, Prabhat Kumar, Can Ayas, Matthijs Langelaar
In Metal Additive Manufacturing (MAM), support structures serve not only for mechanical supports but also for heat dissipation, preventing overheating in the melt zone. Although a high support volume aids heat dissipation, it significantly increases printing time, material wastage, and post-processing efforts. Additionally, contact area between the part and the supports often has higher surface roughness, which compromises part quality. This paper presents a novel density-based Topology Optimization (TO) technique for designing support structures optimized for efficient heat evacuation while keeping the part design fixed. First, a simplified MAM model, already established in the literature, is used to identify regions prone to overheating, referred to as ‘hotspots.’ This hotspot information is then used to formulate a TO problem that minimizes support volume while regulating the heat evacuation efficiency of the supports through thermal compliance which is defined as a constraint. For calculation of thermal compliance, a thermal load is defined using the hotspot information while the baseplate acts as a heat sink. To reduce post-processing costs, a concept of vicinity penalization is introduced, promoting the minimization of the part-support interface area. First, a set of 2D results is presented to demonstrate the method’s effectiveness and explain the influence of various parameters. Next, the TO algorithm is applied to a real-size 3D part and the results are discussed. Finally, the performance of the optimized supports is evaluated using a transient layer-by-layer AM simulation. ...

Topology optimization, 3D-printing and experimental validation

Journal article (2026) - Prabhat Kumar, Chandra Prakash, Josh Pinskier, David Howard, Matthijs Langelaar
Typically, heuristic/trial-based approaches are used to design soft pneumatic grippers (SPGs). This paper presents a systematic topology optimization framework for developing SPGs. The design-dependent nature of actuating load is modeled using Darcy's law with an added drainage term. A 2D soft arm unit is then optimized as a compliant mechanism under pneumatic loading. To ensure the design is robust and manufacturable, the problem is formulated as a min-max optimization, where output deformations of blueprint and eroded designs are considered. A volume constraint is imposed on the blueprint part, while a strain-energy constraint is enforced on the eroded part. The Method of Moving Asymptotes is employed to solve optimization problems. The optimized 2D part is extruded suitably to generate a 3D unit. Ten such 3D units are assembled to create a gripper arm. Both the optimized 2D unit and the corresponding gripper arm outperform their conventional rectangular designs under pneumatic loading, demonstrating the efficacy of the proposed approach. The arms are fabricated using the SLA printing technique. Numerical and experimental results are compared at different pneumatic loads. Four 3D-printed arms are integrated with a supporting structure to form the SPG. The gripping action of the SPG is demonstrated on objects with different weights, sizes, structures, stiffnesses, and shapes. ...
Journal article (2025) - M. J.B. Theulings, L. Noël, M. Langelaar, R. Maas
In density-based topology optimization of flow problems, flow in the solid domain is generally inhibited using a penalization approach. Setting an appropriate maximum magnitude for the penalization traditionally requires manual tuning to find an acceptable compromise between flow solution accuracy and design convergence. In this work, three penalization approaches are examined, the Darcy (D), the Darcy with Forchheimer (DF), and the newly proposed Darcy with filtered Forchheimer (DFF) approach. Parameter tuning is reduced by analytically deriving an appropriate penalization magnitude for accuracy of the flow solution. The Forchheimer penalization is found to be required to reliably predict the accuracy of the flow solution. The state-of-the-art D and DF approaches are improved by developing the novel DFF approach, based on a spatial average of the velocity magnitude. In comparison, the parameter selection in the DFF approach is more reliable, as convergence of the flow solution and objective convexity are more predictable. Moreover, a continuation approach on the maximum penalization magnitude is derived by numerical inspection of the convexity of the pressure drop response. Using two-dimensional optimization benchmarks, the DFF approach reliably finds accurate flow solutions and is less prone to converge to inferior local optima. ...
Journal article (2025) - Hendrik J. Algra, Zichao Li, Matthijs Langelaar, Farbod Alijani, Alejandro M. Aragón
The quality factor (Q factor) of nanomechanical resonators is influenced by geometry and stress, a phenomenon called dissipation dilution. Studies have explored maximizing this effect, leading to softly-clamped resonator designs. This paper proposes a topology optimization methodology to design two-dimensional nanomechanical resonators with high Q factors by maximizing dissipation dilution. A formulation based on the ratio of geometrically nonlinear to linear modal stiffnesses of a prestressed finite element model is used, with its corresponding adjoint sensitivity analysis formulation. Systematic design in square domains yields geometries with comparable Q factors to literature. We analyze the trade-offs between resonance frequency and quality factor, and how these are reflected in the geometry of resonators. We further apply the methodology to optimize a resonator on a full hexagonal domain. By using the entire mesh—i.e., without assuming any symmetries—we find that the optimizer converges to a two-axis symmetric design comprised of four tethers. ...
Journal article (2025) - Reinier Giele, Can Ayas, Matthijs Langelaar
A framework is proposed for geometric filters in density-based topology optimization. Most geometric filters feature density detection in a specified region of interest. In this method, this operation is decoupled from the finite element mesh by using interpolated densities. This allows for the filter configuration (e.g. tool orientation or printing direction) to be optimized simultaneously with the geometric layout. The framework is presented in a generic manner, and demonstrated on filters for: milling with simultaneous optimization of milling orientation; jetting with simultaneous optimization of jetting positions; and printing with simultaneous optimization of printing orientation. The performance of the framework is tested with numerical examples for compliance in 2D and 3D on a structured mesh, and in 2D on an unstructured mesh. The framework can extend the design freedom of existing filters, and can serve as a basis for the development of new geometric filters. ...
Journal article (2025) - Reinier Giele, Can Ayas, Matthijs Langelaar
A novel feature mapping topology optimization method is presented, allowing for the creation of features with highly flexible shapes. The method easily integrates with conventional density-based formulations. Feature shapes are implicitly described by NURBS control points. The feature shape dictates the locations of two sets of projection points to represent the solid void boundaries. At these projection points, density values are projected onto a finite element mesh. The method optimizes feature shapes in a gradient-based manner, while allowing more specific control of the feature shapes than classical level set methods. Several feature fields can be combined to create a final output design. It is found that the eminent flexibility of the NURBS-based feature definition is a benefit but also requires additional regularization to guarantee stability of the optimization. ...
Journal article (2024) - Breno Vincenzo de Almeida, Renato Pavanello, Matthijs Langelaar
The design of smart structures is challenging because of the integrated electromechanical modelling and optimization of actuators, sensors and load-bearing structures. To simplify the design process, it is common to decouple some of the components and physics and develop each part separately, which could lead to suboptimal systems. To improve the overall design of active structures, we propose an integrated and fully coupled design methodology for a certain class of smart structures. Specifically, this paper presents a numerical framework for the simultaneous application of density-based topology optimization of multi-material conductive compliant mechanisms and a composite multi-layered geometry-projection method for the optimization of the size, position and orientation of embedded piezoelectric stack actuators. Their electromechanical properties are represented in a continuum-based setting by an orientation- and geometry-dependent equivalent material model and their activation depends on the distribution of conductive material in the structure. Furthermore, a novel constraint on the polarization of the actuators is proposed to avoid unwanted designs that could cause their mechanical degradation. A set of numerical examples is analysed and discussed. The proposed framework exhibits promising results, with significant improvements in comparison to a benchmark problem. ...
Journal article (2024) - Yi Xia, Andrew Liew, Hongfei Wu, Matthijs Langelaar, Max A.N. Hendriks, Yuanlong Yang, Meisam Takalloozadeh, Matthew Gilbert
When employing the strut-and-tie modelling (STM) method in the conceptual design of reinforced concrete structures, a suitable strut-and-tie (ST) model indicating load transfer mechanisms first needs to be identified. Topology optimization (TO) methods have frequently been used for this purpose. However, although TO methods employing either a ground-structure or a continuum-based TO approach can be used, the performance and effectiveness of these two methods have not been systematically investigated and compared. To obtain a better understanding of the characteristics of both methods, a systematic comparison procedure is proposed to investigate the generation process and the resulting ST designs. Three aspects, relating to structural performance, economic issues, and method applicability are considered in the comparison, with six metrics formulated to quantify these aspects. Based on investigation of designs for three reinforced concrete elements incorporating typical discontinuity regions (two 2D cases and a 3D case), the performance of the two methods is assessed. It is found that both methods result in safe and efficient ST designs, with comparable structural performance, while some differences in terms of computation time and usability are observed. ...
In topology optimization of transient problems, memory requirements and computational costs often become prohibitively large due to the backward-in-time adjoint equations. Common approaches such as the Checkpointing (CP) and Local-in-Time (LT) algorithms reduce memory requirements by dividing the temporal domain into intervals and by computing sensitivities on one interval at a time. The CP algorithm reduces memory by recomputing state solutions instead of storing them. This leads to a significant increase in computational cost. The LT algorithm introduces approximations in the adjoint solution to reduce memory requirements and leads to a minimal increase in computational effort. However, we show that convergence can be hampered using the LT algorithm due to errors in approximate adjoints. To reduce memory and/or computational time, we present two novel algorithms. The hybrid Checkpointing/Local-in-Time (CP/LT) algorithm improves the convergence behavior of the LT algorithm at the cost of an increased computational time but remains more efficient than the CP algorithm. The Parallel-Local-in-Time (PLT) algorithm reduces the computational time through a temporal parallelization in which state and adjoint equations are solved simultaneously on multiple intervals. State and adjoint fields converge concurrently with the design. The effectiveness of each approach is illustrated with two-dimensional density-based topology optimization problems involving transient thermal or flow physics. Compared to the other discussed algorithms, we found a significant decrease in computational time for the PLT algorithm. Moreover, we show that under certain conditions, due to the use of approximations in the LT and PLT algorithms, they exhibit a bias toward designs with short characteristic times. Finally, based on the required memory reduction, computational cost, and convergence behavior of optimization problems, guidelines are provided for selecting the appropriate algorithms. ...
Journal article (2024) - Josh Pinskier, Xing Wang, Lois Liow, Yue Xie, Prabhat Kumar, Matthijs Langelaar, David Howard
Soft grippers are ideal for grasping delicate, deformable objects with complex geometries. Universal soft grippers have proven effective for grasping common objects, however complex objects or environments require bespoke gripper designs. Multi-material printing presents a vast design-space which, when coupled with an expressive computational design algorithm, can produce numerous, novel, high-performance soft grippers. Finding high-performing designs in challenging design spaces requires tools that combine rapid iteration, simulation accuracy, and fine-grained optimization across a range of gripper designs to maximize performance, no current tools meet all these criteria. Herein, a diversity-based soft gripper design framework combining generative design and topology optimization (TO) are presented. Compositional pattern-producing networks (CPPNs) seed a diverse set of initial material distributions for the fine-grained TO. Focusing on vacuum-driven multi-material soft grippers, several grasping modes (e.g. pinching, scooping) emerging without explicit prompting are demonstrated. Extensive automated experimentation with printed multi-material grippers confirms optimized candidates exceed the grasp strength of comparable commercial designs. Grip strength, durability, and robustness is evaluated across 15,170 grasps. The combination of fine-grained generative design, diversity-based design processes, high-fidelity simulation, and automated experimental evaluation represents a new paradigm for bespoke soft gripper design which is generalizable across numerous design domains, tasks, and environments. ...
Journal article (2024) - Reinier Giele, Can Ayas, Matthijs Langelaar
Topology optimization methods are used to design high performance structural components that often have complex geometric layouts. In several industries, components are required to be cleanable, and for this research cleaning by jetting is considered. Thus, being able to ensure jet access on the entire surface of a structure is of interest in topology optimization. In this paper, a jetting filter is proposed, that turns a blueprint design into a jet accessible design. Two methods are considered to find an access field for each jet. These individual jet access fields are then combined into a total access field, to obtain a cleanable design. Consistent sensitivity analysis is used and the additional computational cost of the jetting filter is modest compared to the finite element analysis. The performance of the two methods is demonstrated with 2D and 3D numerical examples for mechanical and thermal topology optimization problems. ...
Journal article (2023) - Vibhas Mishra, Can Ayas, Matthijs Langelaar
In metal Additive Manufacturing (AM), the deposited material is subjected to a series of heating and cooling cycles. The locally occurring temperature extremes and cooling rates determine solid-state phase fractions, material microstructure, texture, and ultimately the local material properties. As the shape of a part determines the local thermal history during AM, this offers an opportunity to influence these material properties through design. In this paper, we present a way to obtain desired properties by controlling the local thermal history. This is achieved through topology optimization of the printed part while considering its entire transient thermal history. As an example of this approach, this work focuses on high strength low alloy steels, where resulting phase fractions significantly influence mechanical properties such as yield strength and ductility. These solid-state phase fractions depend on cooling rates in a particular critical temperature range. The phase composition and hence the local yield strength in target regions can be controlled by constraining the cooling time in this range. Numerical examples illustrate the capability of the proposed approach in adapting part designs to achieve various desired material properties. ...
Journal article (2023) - Marek Slebioda, Reinier Giele, Matthijs Langelaar
This paper presents a density based topology optimization method for infinite fatigue life constraints of non-proportional load cases, with a specific focus on parts with cyclic symmetry. Considering non-proportional loads in topology optimization significantly broadens the types of design problems that can be handled. The method estimates the local variation in Signed von Mises stress using a smooth min/max function and constrains the resulting stress amplitude using established stress based topology optimization methods. Accounting for non-proportionality of loading significantly increases the computation cost with respect to existing proportional methods, as the time-varying stress field needs to be computed. Inertia effects are neglected in the structural analysis. Therefore, a quasi-static analysis is used to obtain the stress history. To reduce the computational cost, advantage is taken of cyclic symmetric properties to reduce the number of necessary time steps to evaluate. This reduces the computational cost roughly proportional to the number of unique load time steps present in the repeated segments as opposed to a standard implementation. The method is tested on numerical examples in 2D and 3D for both proportional and non-proportional loads and was found to be locally accurate up to the accuracy of the constraint aggregation. ...
Review (2023) - Mohamad Bayat, Olga Zinovieva, Jesper Hattel, Federico Ferrari, Can Ayas, Matthijs Langelaar, Jon Spangenberg, Roozbeh Salajeghe, Konstantinos Poulios, Sankhya Mohanty, Ole Sigmund
Additive manufacturing (AM) processes have proven to be a perfect match for topology optimization (TO), as they are able to realize sophisticated geometries in a unique layer-by-layer manner. From a manufacturing viewpoint, however, there is a significant likelihood of process-related defects within complex geometrical features designed by TO. This is because TO seldomly accounts for process constraints and conditions and is typically perceived as a purely geometrical design tool. On the other hand, advanced AM process simulations have shown their potential as reliable tools capable of predicting various process-related conditions and defects. Thus far, geometry design by topology optimization and multiphysics manufacturing simulations have been viewed as two mostly separate paradigms, whereas one should really conceive them as one holistic computational design tool. More specifically, AM process models provide input to physics-based TO, where consequently, not only the designed component will function optimally, but also will have near-to-minimum manufacturing defects. In this regard, we aim at giving a thorough overview of holistic computational design tool concepts applied within AM. First, literature on TO for performance optimization is reviewed and then the most recent developments within physics-based TO techniques related to AM are covered. Process simulations play a pivotal role in the latter type of TO and serve as additional constraints on top of the primary end-user optimization objectives. As a natural consequence of this, a comprehensive and detailed review of non-metallic and metallic additive manufacturing simulations is performed, where the latter is divided into micro-scale and deposition-scale simulations. Material multi-scaling techniques, which are central to the process-structure-property relationships, are reviewed next, followed by a subsection on process multi-scaling techniques, which are reduced-order versions of advanced process models and are incorporable into physics-based TO due to their lower computational requirements. Finally the paper is concluded and suggestions for further research paths discussed. ...

Design, experiments and numerical simulation of optimized concrete girders

Journal article (2023) - Nadine Pressmair, Yi Xia, Hongfei Wu, Matthijs Langelaar, Max A.N. Hendriks, Ahmad Majdouba, Mihir Mogra, Hezi Grisaro, Oded Amir, Benjamin Kromoser
Concrete, as the most widely used construction material, is associated with a high environmental impact. Within the present study, structural optimization is the method of choice to counter this issue. The entire process, from optimization, to design, experiments and numerical simulation is outlined. Embedded in the framework of a design competition (Concrete Girder Optimization Competition 2021), a bridge between structural engineering and mathematical optimization is demonstrated. Two design concepts for optimized concrete girders, one with internal and one with external reinforcement, yet both based on strut-and-tie modeling, were investigated. Within the boundaries of the competition, several conclusions can be drawn: The results indicate the importance of an adequate structural interpretation of topology optimization results to obtain satisfying structural performance. The environmental evaluation outlines that the reinforcement mass has a substantial share in the total Global Warming Potential. A successful numerical re-simulation of selected girders can serve as a modeling base for other researchers. Compared to a conventionally designed girder an increase in resource efficiency, measured by load-carrying capacity versus environmental impact, of more than 30% was achieved. ...
Conference paper (2023) - Prabhat Kumar, Josh Pinskier, David Howard, Matthijs Langelaar
Compliant mechanisms actuated by pneumatic loads are receiving increasing attention due to their direct applicability as soft robots that perform tasks using their flexible bodies. Using multiple materials to build them can further improve their performance and efficiency. Due to developments in additive manufacturing, the fabrication of multi-material soft robots is becoming a real possibility. To exploit this opportunity, there is a need for a dedicated design approach. This paper offers a systematic approach to developing such mechanisms using topology optimization. The extended SIMP scheme is employed for multi-material modeling. The design-dependent nature of the pressure load is modeled using the Darcy law with a volumetric drainage term. Flow coefficient of each element is interpolated using a smoothed Heaviside function. The obtained pressure field is converted to consistent nodal loads. The adjoint-variable approach is employed to determine the sensitivities. A robust formulation is employed, wherein a min-max optimization problem is formulated using the output displacements of the eroded and blueprint designs. Volume constraints are applied to the blueprint design, whereas the strain energy constraint is formulated with respect to the eroded design. The efficacy and success of the approach are demonstrated by designing pneumatically actuated multi-material gripper and contractor mechanisms. A numerical study confirms that multiple-material mechanisms perform relatively better than their single-material counterparts. ...
In design optimization of bulk handling equipment (BHE) we generally focus on the mean performance of the equipment. However, granular materials behave stochastic due to irregularities in particle shape and size which leads to stochastic performance of the equipment. To include the stochastic performance we propose robust metamodel-based design optimization (MBDO). The used metamodels are trained with stochastic performance data from randomly repeated discrete element method (DEM) simulations and predict mean and variance of the equipment performance. This method is compared to the conventional deterministic optimization method by means of a case study of a discharging hopper including verification and validation. The robust MBDO shows more distinctive optimal designs compared to the deterministic approach. In addition, the DEM-based metamodel is a relatively accurate method to predict DEM-model simulation results. However, the validation indicates that differences between DEM-model and experimental results highly affect the reliability of the found optima. ...