The response of maritime structures can be multiaxial, involving predominant mode-I and non-negligible mode-III components. Adopting a stress distribution formulation based effective notch stress as fatigue strength parameter for mixed mode-{I, III} multiaxial fatigue assessment purposes, a mode-I equivalent von Mises type of failure criterion has been established at the critical fracture plane. Counting includes a cycle-by-cycle non-proportionality measure and damage accumulation is based on a linear model. Distinguished mode specific and material characteristic strength and mechanism contributions in terms of respectively the resistance curve intercept and mean stress induced response ratio coefficient, resistance curve slope and material characteristic length, have been incorporated. Evaluating the mid-cycle fatigue resistance, the outperformance is impressive. The analysed multiaxial mode-{I, III} data fits the uniaxial mode-I reference data scatter band and a single resistance curve can be used for fatigue assessment.

@en

Arc-welded joints in steel maritime structures are typically identified as weakest links in terms of fatigue limit state performance. Multiaxiality can be involved, consisting of predominant mode-I and non-negligible mode-III components. Aiming to answer the question if a cracked geometry based fatigue strength parameter would outperform an intact geometry based one like the effective notch stress, the total stress is adopted. A von Mises type of criterion is defined at the critical fracture plane and includes mode specific and material characteristic strength and mechanism contributions. A lifetime dependent shear strength coefficient is introduced to cover the resistance curves intercepts and slopes, whereas the total stress parameter contains the mean stress contribution as well as the (mixed) mode dependent notch and crack tip elastoplasticity coefficients, reflecting an interaction mechanism. Cycle counting includes a cycle-by-cycle non-proportionality measure and damage accumulation is based on a linear model. Evaluating mid-cycle fatigue resistance data, the total stress and effective notch stress performance turns out to be similar. However, the total stress related elastoplasticity coefficients are an explicit and sensitive measure to incorporate the actual physics of the fatigue damage process, whereas the material characteristic lengths for the effective notch stress seem to be more implicit and less sensitive ones.

@en

Parallel computing is omnipresent in today's scientific computer landscape, starting at multicore processors in desktop computers up to massively parallel clusters. While domain decomposition methods have a long tradition in computational mechanics to decompose spatial problems into multiple subproblems that can be solved in parallel, advancing solution schemes for dynamics or quasi-statics are inherently serial processes. For quasi-static simulations, however, there is no accumulating ‘time’ discretization error, hence an alternative approach is required. In this paper, we present an Adaptive Parallel Arc-Length Method (APALM). By using a domain parametrization of the arc-length instead of time, the multi-level error for the arc-length parametrization is formed by the load parameter and the solution norm. Given coarse approximations of arc-length intervals, finer corrections enable the parallelization of the presented method. This results in an arc-length method that is parallel within a branch and inherently adaptive. This concept is easily extended for bifurcation problems. The performance of the method is demonstrated using isogeometric Kirchhoff-Love shells on problems with snap-through and pitch-fork instabilities and applied to the problem of a snapping meta-material. These results show that parallel corrections are performed in a fraction of the time of the serial initialization, achievable on desktop scale.@en

Mesh adaptivity is a technique to provide detail in numerical solutions without the need to refine the mesh over the whole domain. Mesh adaptivity in isogeometric analysis can be driven by Truncated Hierarchical B-splines (THB-splines) which add degrees of freedom locally based on finer B-spline bases. Labeling of elements for refinement is typically done using residual-based error estimators. In this paper, an adaptive meshing workflow for isogeometric Kirchhoff–Love shell analysis is developed. This framework includes THB-splines, mesh admissibility for combined refinement and coarsening and the Dual-Weighted Residual (DWR) method for computing element-wise error contributions. The DWR can be used in several structural analysis problems, allowing the user to specify a goal quantity of interest which is used to mark elements and refine the mesh. This goal functional can involve, for example, displacements, stresses, eigenfrequencies etc. The proposed framework is evaluated through a set of different benchmark problems, including modal analysis, buckling analysis and non-linear snap-through and bifurcation problems, showing high accuracy of the DWR estimator and efficient allocation of degrees of freedom for advanced shell computations.

@en

The predominant mode-I response of maritime structures can be multiaxial, involving out-of-plane mode-III shear components. Semi-analytical mode-III notch stress distribution formulations have been established for critical details like welded T-joints and cruciform joints, reflecting (non-)symmetry with respect to half the plate thickness. Using a stress distribution formulation based effective notch stress as fatigue strength criterion, the mode-III welded joint mid-cycle fatigue resistance characteristics have been investigated. In comparison to mode-I, the material characteristic length and resistance curve slope estimate suggest the fatigue damage process to be even more an initiation related near-surface phenomenon. Mean shear stress effects seem insignificant.

@en

Modelling nonlinear phenomena in thin rubber shells calls for stretch-based material models, such as the Ogden model which conveniently utilizes eigenvalues of the deformation tensor. Derivation and implementation of such models have been already made in Finite Element Methods. This is, however, still lacking in shell formulations based on Isogeometric Analysis, where higher-order continuity of the spline basis is employed for improved accuracy. This paper fills this gap by presenting formulations of stretch-based material models for isogeometric Kirchhoff–Love shells. We derive general formulations based on explicit treatment in terms of derivatives of the strain energy density functions with respect to principal stretches for (in)compressible material models where determination of eigenvalues as well as the spectral basis transformations is required. Using several numerical benchmarks, we verify our formulations on invariant-based Neo-Hookean and Mooney–Rivlin models and with a stretch-based Ogden model. In addition, the model is applied to simulate collapsing behaviour of a truncated cone and it is used to simulate tension wrinkling of a thin sheet. @en

The characteristic far field response spectrum of welded joints – the governing fatigue sensitive locations in steel marine structures – is predominantly linear elastic, meaning mid- and high-cycle fatigue (MCF and HCF) is most important for design. Using the effective notch stress- and the total stress concept, involving respectively S_e and S_T as intact- and cracked geometry fatigue strength criterion, one MCF-HCF resistance curve has been obtained for all welded joints. A generalised random fatigue limit model explicitly incorporating the MCF life time and HCF strength limit scatter provides statistically the most accurate fatigue strength and fatigue life time estimates. Similar MCF performance is obtained for S_e and S_T. Although crack growth dominates the MCF damage process, the results for an initiation related criterion like S_e and natural crack growth related criterion like S_T are similar. Adopting S_e rather than S_T as fatigue strength criterion naturally related to the crack initiation dominated HCF region showing the largest data scatter may explain the better effective notch stress concept HCF performance. Since the HCF resistance scatter is relatively large, the MCF-HCF generalised random fatigue limit model design curves show approximately 1-slope behaviour. meaning that for design purposes a linear Basquin model approximation rather than a piecewise continuous bi-linear MCF-HCF formulation according to guidelines, standards and classification notes should be adopted.

@en

The first part of the paper presents a partitioned fluid–structure interaction (FSI) coupling for the non-uniform flow hydro-elastic analysis of highly flexible propellers in cavitating and non-cavitating conditions. The chosen fluid model is a potential flow solved with a boundary element method (BEM). The structural sub-problem has been modelled with a finite element method (FEM). In the present method, the fully partitioned framework allows one to use another flow or structural solver. An important feature of the present method is the time periodic way of solving the FSI problem. In a time periodic coupling, the coupling iterations are not performed per time step but on a periodic level, which is necessary for the present BEM–FEM coupling, but can also offer an improved convergence rate compared to a time step coupled method. Thus, it allows to solve the structural problem in the frequency domain, meaning that any transients, which slow down the convergence process, are not computed. As proposed in the method, the structural equations of motion can be solved in modal space, which allows for a model reduction by involving only a limited number of mode shapes. The second part of the paper includes a validation study on full-scale. For the full-scale validation study a purposely designed composite propeller with a diameter of 1 m has been manufactured. Also an underwater measurement set-up including a stereo camera system, remote control of the optics and illumination system has been developed. The propeller design and the underwater measurement set-up are described in the paper. During sea trials blade deflections have been measured in three different positions. A comparison between measured and calculated torque shows that the measured torque is much larger than computed. This is attributed to the differences between effective and nominal wakefields, where the latter one has been used for the calculations. To correct for the differences between measured and computed torque the calculated pressures have been amplified accordingly. In that way the deformations which have been computed with the BEM–FEM coupling for non-uniform flows became very similar to the measured results.

@en

Wrinkling or pattern formation of thin (floating) membranes is a phenomenon governed by buckling instabilities of the membrane. For (post-) buckling analysis, arc-length or continuation methods are often used with a priori applied perturbations in order to avoid passing bifurcation points when traversing the equilibrium paths. The shape and magnitude of the perturbations, however, should not affect the post-buckling response and hence should be chosen with care. In this paper, our primary focus is to develop a robust arc-length method that is able to traverse equilibrium paths and post-bifurcation branches without the need for a priori applied perturbations. We do this by combining existing methods for continuation, solution methods for complex roots in the constraint equation, as well as methods for bifurcation point indication and branch switching. The method has been benchmarked on the post-buckling behaviour of a column, using geometrically non-linear isogeometric Kirchhoff-Love shell element formulations. Excellent results have been obtained in comparison to the reference results, from both bifurcation point and equilibrium path perspective.@en

Highly varying sloshing loads are a superposition of load components resulting from a sequence of different physical phenomena. However, not all features of spatial and temporal variations of sloshing loads and associated phenomena are equally important when failure of structure is considered. Therefore, the prediction of sloshing loads should be focused on those load components which lead to failure. These components can be found by employing a structural model, which should be fast computationally considering the huge number of possible sloshing loads. This paper presents a reduced order model based on the beam-foundation model which is derived for the Mark-III cargo containment system. The model is validated against a detailed finite element model and it conservatively predicts the stresses at failure locations. The calculation time using the model is approximately two orders smaller in comparison to a finite element model computation, which allows the model to be applied for finding governing load components and associated physical phenomena.

@en

Fatigue is a governing design limit state for marine structures. Welded joints are important in that respect. The weld notch stress (intensity) distributions contain essential information and formulations have been established to obtain a total stress fatigue damage criterion and corresponding fatigue resistance curve; a total stress concept. However, the involved weld load carrying stress model does not provide the required estimates and trends for varying geometry dimensions and loading & response combinations. A new one has been developed and performance evaluation for T-joints and cruciform joints in steel marine structures shows that in comparison with the nominal stress, hot spot structural stress and effective notch stress concept based results up to 50% more accurate fatigue design life time estimates can be obtained. Taking advantage of the weld notch stress formulations, the effective notch stress concept performance has improved adopting a stress-averaged criterion rather than a fictitious notch radius-based one.

@en

A special type of fluid–structure interaction (FSI) problems are problems with periodic boundary conditions like in turbomachinery. The steady state FSI response of these problems is usually calculated with similar techniques as used for transient FSI analyses. This means that, when the fluid and structure problem are not simultaneously solved with a monolithic approach, the problem is partitioned into a fluid and structural part and that each time step coupling iterations are performed to account for strong interactions between the two sub-domains. This paper shows that a time-partitioned FSI computation can be very inefficient to compute the steady state FSI response of periodic problems. A new approach is introduced in which coupling iterations are performed on periodic level instead of per time step. The convergence behaviour can be significantly improved by implementing existing partitioned solution methods as used for time step coupling (TSC) algorithms in the time periodic coupling (TPC) framework. The new algorithm has been evaluated by comparing the convergence behaviour to TSC algorithms. It is shown that the number of fluid–structure evaluations can be considerably reduced when a TPC algorithm is applied instead of a TSC. One of the most appealing advantages of the TPC approach is that the structural problem can be solved in the frequency domain resulting in a very efficient algorithm for computing steady state FSI responses.

@en

Structural geometry and stochastic loads such as swell and wind seas can typically induce multiaxial stress states in welded details of marine structures. It is known that such complex time varying stress states determine the fatigue resistance of welded steel joints. Therefore, it is of importance to account for them in fatigue lifetime estimation. Over the past few decades a wide variety of design guidelines and methods have been developed for multiaxial fatigue assessment, but so far there does not exist a general hypothesis applicable to all possible load cases. This study provides an overview of the current state-ofthe-art in academia and engineering practice in terms of multiaxial fatigue assessment, and is focusing on the application to welded joints in marine structures. The progress of different approaches and methods is elaborated and commented upon, taking their hypothesis and (physical) basis into consideration. The insights that are provided in this paper form a valuable foundation for future investigations and emphasize the necessity of experimental proofs and model validation.

@en

Boundary element methods (BEM) have been used for propeller hydrodynamic calculations since the 1990s. More recently, these methods are being used in combination with finite element methods (FEM) in order to calculate flexible propeller fluid–structure interaction (FSI) response. The main advantage of using BEM for flexible propeller FSI calculations is the relatively low computational demand in comparison with higher fidelity methods. However, the BEM modelling of flexible propellers is not straightforward and requires several important modelling decisions. The consequences of such modelling choices depend significantly on propeller structural behaviour and flow condition. The two dimensionless quantities that characterise structural behaviour and flow condition are the structural frequency ratio (the ratio between the lowest excitation frequency and the fundamental wet blade natural frequency) and the reduced frequency. For both, general expressions have been derived for (flexible) marine propellers. This work shows that these expressions can be effectively used to estimate the dry and wet fundamental blade frequencies and the structural frequency ratio. This last parameter and the reduced frequency of vibrating blade flows is independent of the geometrical blade scale as shown in this work. Regarding the BEM-FEM coupled analyses, it is shown that a quasi-static FEM modelling does not suffice, particularly due to the fluid-added mass and hydrodynamic damping contributions that are not negligible. It is demonstrated that approximating the hydro-elastic blade response by using closed form expressions for the fluid added mass and hydrodynamic damping terms provides reasonable results, since the structural response of flexible propellers is stiffness dominated, meaning that the importance of modelling errors in fluid added mass and hydrodynamic damping is small. Finally, it is shown that the significance of recalculating the hydrodynamic influence coefficients is relatively small. This fact might be utilized, possibly in combination with the use of the closed form expressions for fluid added mass and hydrodynamic damping contributions, to significantly reduce the computation time of flexible propeller FSI calculations@en

Concern for crack initiation and growth under cyclic loading as well as unstable crack propagation and tearing in the ship and offshore structures. Due attention shall be paid to the suitability and uncertainty of physical models and testing. Consideration is to be given to practical application, statistical description and fracture control methods in design, fabrication and service.@en

Fatigue is typically a governing limit state for marine structures. Welded joints are the weakest links in that respect. Physics involve several resistance dimensions, a range of scales and distinct contributions in different stages of the accumulative damage process. Fatigue damage criteria developed over time have been classified with respect to type of information, geometry, parameter and process zone including plane and life region annotations. The criteria are evaluated regarding model (in)capabilities, showing up to what extent (governing) physics are taken into account. Modelling developments and trends towards complete strength, multi-scale and total life criteria have been identified. Incorporating all four (interacting) fatigue resistance dimensions: material, geometry, loading & response and environment translates into a complete strength fatigue damage criterion. Considering macro-, meso- and micro-scale information provides a multi-scale fatigue damage criterion. Correlation of crack initiation and growth requires matching intact and cracked geometry parameters, revealing a total life fatigue damage criterion. HIGHLIGHTS • Classification of fatigue damage criteria with respect to type of information, geometry, parameter and process zone including plane and life region annotations. • Identification of modelling developments and trends towards complete strength, multi-scale and total life fatigue damage criteria for welded joints in marine structures. ABBREVIATIONS: CA: constant amplitude; FE: finite element; FSS: full-scale structure; HCF: high cycle fatigue, life time range N = O(5·10⁶ … 10⁹) cycles; (N)LC: (non-)load carrying; LCF: low cycle fatigue, life time range N = O(10¹ … 10⁴) cycles; LSS: large-scale specimen; MCF: medium cycle fatigue, life time range N = O(10⁴ … 5·10⁶) cycles; mSC: micro- and meso-scopic stress concentration; MSC: macro-scopic stress concentration; (N)SIF: (notch) stress or strain intensity factor; SCF: stress or strain concentration factor; SED: strain energy density; SSS: small-scale specimen; VA: variable amplitude.

@en

The application of composite materials in marine propellers is a relatively recent innovation. Methods have been presented to analyse the hydro-elastic behaviour of these type of propellers and in some studies these methods have been validated as well. Differences between measured and predicted responses are typically explained from inaccuracies in structural or fluid modelling. It is beyond all doubt that for an accurate finite element (FE) model a correct modelling of the fibre orientations and material properties is required. Both subjects are addressed in this work. An approach is presented in order to accurately define the element dependent fibre orientations in doubly curved geometries like (marine) propeller blades. In order to improve the structural response prediction this paper presents an inverse method based on experimental and numerical results which can be used for structural identification and FE model updating. In the developed approach the residual between measurement results obtained with static experiments and results obtained with an FE model is minimized by adapting the stiffness properties in the FE calculation. This method has been successfully applied to two small scale composite propellers. The obtained material properties have been determined with a relatively high confidence level. A verification by means of measured and calculated eigenfrequencies show also that accurate results are obtained with the inverse method. Therefore, this paper gives a positive answer on the research question whether it is possible to determine the stiffness properties of small scale composite marine propeller blades from a static experimental data.

@en

In engineering practice, multiaxial fatigue analyses are often avoided due to their complexity and computational intensity. However, damages have been encountered in turret bearings of Floating Production Storage and Offloading vessel (FPSO) offloading buoys which were likely caused by multiaxial fatigue. The Dang Van criterion has often been used to assess problems with multiaxial fatigue in rolling contacts. Therefore, this study set out to validate the application of the Dang Van criterion to turret bearings of FPSO offloading buoys. For this purpose, the criterion was corrected with a horizontal conservative locus for compressive hydrostatic stresses. Three load cases were identified based on the seakeeping analysis of an FPSO offloading buoy equipped with a wheel-rail turret bearing. For each load case, the surface pressure distribution and sub-surface stress states were determined analytically. Staircase tests were used to determine the characteristic parameters (α and β) of the Dang Van curve. Then, the Dang Van criterion was corrected and used to perform a multiaxial fatigue analysis in the critically stressed area of the wheel-rail contact. Finally, full-scale, long-duration fatigue tests were used to validate the results. The corrected Dang Van criterion shows agreement with the experimental results and is not rejected as multiaxial fatigue criterion for application to turret bearings in FPSO offloading buoys.@en

Marine structures are particularly prone to action of waves, winds and currents with stochastically varying composition, intensities and directions. Therefore, resultant stresses may cause multiaxial fatigue in specific welded structural details. For the assessment of multiaxial fatigue in welded joints, a wide variety of methods have been suggested. However, there is still no consensus on a method which can correctly account for non-proportional and variable amplitude loading. This paper beholds a comparative study of multiaxial fatigue methods applicable for design of marine structures. For the purpose of comparison several load cases were defined including non-proportional and variable amplitude loadings with different normal and shear stress amplitude ratios. Three types of methods are compared: those described by three different codes (i.e. Eurocode 3, IIW and DNV-GL), those described by three different multiaxial fatigue approaches from literature (i.e. Modified Carpinteri-Spagnoli Criterion, Modified Wohler Curve Method and Effective Equivalent Stress Hypothesis) and an approach based on Path-Dependent-Maximum-Range multiaxial cycle counting. From this study it has been concluded that non-proportional variable amplitude loading has a significant negative impact on the fatigue lifetime estimates, and that further research and experimental testing are essential to come to a consensus.@en