A modeling approach to simulate ice-induced vibrations of vertically sided offshore structures in ice tank experiments is presented. The technique combines replica modeling with the preservation of kinematics during ice-structure interaction. The technique was chosen based on the theoretical understanding that ice-induced vibrations are caused by an energy exchange between the structure and the ice. The mechanism is controlled by primarily four aspects: the kinematics during ice-structure interaction, the degree to which the ice can resist higher loading at low velocities prior to failure (velocity effect), the existence of a transition speed from ductile-to-brittle failure, and the mean ice load level. A model ice type which resulted in a velocity effect and provided a transition speed comparable to that of sea ice was developed and used during ice tank experiments. A scaling factor, derived from the comparison between the mean brittle crushing ice load of the full-scale event and the in-situ measured mean brittle crushing model ice load, was applied to scale structure properties of a numerical model. This model was implemented during real-time hybrid simulations in model ice to preserve kinematics during the ice-structure interaction. To verify the proposed scaling approach, rigid indenter experiments covering velocities from 0.1 mm s⁻¹ to 500 mm s⁻¹ and dynamic ice-induced vibration experiments of structures with varying aspect ratios (8 and 12) and shapes (cylindrical and rectangular) were conducted. Neither the aspect ratio nor shape appeared to influence the development of ice-induced vibrations significantly. The approach was qualitatively validated by reproducing full-scale ice-induced vibrations as experienced by the Molikpaq platform and Norströmsgrund lighthouse.

@en

Increased activity in planning offshore wind farms in the northern Baltic Sea has renewed interest in studying the effect of ice cones on ice failure mechanisms. In preparation for future experiments with steep ice cones, preliminary ice basin experiments were performed at the Aalto Ice and Wave Tank to investigate how model ice fails against a 3D-printed cylindrical and a conical structure representative of wind turbine foundations. The main motivation behind the two structures is to test ice loads on a monopile foundation and a monopile foundation fitted with an upward-bending ice cone. Each structure was tested at eight different velocities in three ice sheets with varying mechanical properties, including a newly developed, crushing-optimized model ice. The force exerted by the ice on these rigid structures was measured using a six-axis load cell. The results show that ice undergoes mixed-mode failure on the cone in the form of bending, crushing, and spalling, when tested in crushing-optimized ice. Based on the observations and results, it is recommended that model-scale experiments, focused on mixed-mode ice failure, use model ice with a representative compressive to flexural strength ratio, scaled flexural and compressive strength, and the ability to fail in brittle crushing. If these criteria cannot be met, it may be possible to combine test results from different ice sheets, each focused on one ice failure mechanism. Additionally, this study successfully used 3D-printed structures, which present a new and more accessible method of preparing scale models.
@en

With the recent surge in development of offshore wind in the Baltic Sea, Bohai Sea and other ice-prone regions, a need has arisen for new basin tests to qualify the interaction between offshore wind turbines and sea ice. To this end, a series of model tests was performed at the Aalto ice basin as part of the SHIVER project. The tests were aimed at modeling the dynamic interaction between flexible, vertically-sided structures and ice failing in crushing. A real-time hybrid test setup was used which combines numerical and physical components to model the structure. This novel test setup enabled the testing of a wide range of structure types, including existing full-scale structures for which ice-induced vibrations have been documented, and a series of single-degree-of-freedom oscillators to obtain a better understanding of the fundamental processes during dynamic ice-structure interaction. The tests were primarily focused on the dynamic behavior of support structures for offshore wind turbines under ice crushing loads. First results of the campaign show that the combination of the use of cold model ice and not scaling time and deflection of the structure can yield representative ice-structure interaction in the basin. This is demonstrated with experiments during which a scaled model of the Norströmsgrund lighthouse and Molikpaq caisson were used. The offshore wind turbine tests resulted in multi-modal interaction which can be shown to be relevant for the design of the support structure. The dataset has been made publicly available for further analysis.@en

Basin tests were performed at the Aalto Ice Tank to gather data on ice-structure action and interaction from ice failing against a vertically sided cylindrical pile. The tests were performed with a real-time hybrid test setup, which combined physical and numerical components to simulate a range of test structures in real-time. The dataset includes results from tests with offshore wind turbine structures, structural models representing a series of single- and multi-degree-of-freedom oscillators, and scaled dynamic models of the Norströmsgrund lighthouse and the Molikpaq caisson structure. In addition, forced vibration tests and rigid structure tests were performed. Ice loads and structural response were measured with accelerometers, displacement sensors, potentiometers, strain gauges and load cells and the ice-structure interaction process was filmed from three different camera angles. The resulting raw data have been categorized and stored as unfiltered time series. A total of 259 different tests are included in the dataset. The model ice formation procedure and the test temperature were aimed at creating model ice that mimics the material behavior of full-scale saline ice during crushing failure, with a specific focus on the transition from brittle to ductile behavior. The data can be used for validation of models for dynamic ice-structure interaction. The offshore wind turbine data can be used to study the effect of wind loading on the interaction with ice and the effect of the specific dynamic properties of wind turbine structures with monopile foundations on the ice-structure interaction process. The forced-oscillation data can be used to quantify the time and speed dependant aspects of ice loading. The Norströmsgrund lighthouse and the Molikpaq data can be used as a reference comparison to full-scale data on ice loads.

@en