The effect of an automotive paint bake (PB) thermal cycle on the microstructural evolution and the mechanical properties of resistance spot welded advanced high strength steel is presented in this work. Mechanical behavior of the heat-treated welds reveals an increase in maximum cross-tension strength, displacement and subsequently energy absorption capability when 453 K (180 °C)-20 minutes a bake thermal cycle is applied after welding. The microstructures of resistance spot welds with and without a PB heat treatment were characterized using scanning and transmission electron microscopy (TEM). TEM analysis revealed that the weld nugget and HAZ of the resistance spot welds consist of a martensitic microstructure. The microstructural analysis of the post-weld heat-treated samples shows the presence of ε carbides in a martensitic matrix within the weld nugget and the HAZ. It is shown that the improved mechanical response of the paint-baked welds is associated with carbide precipitation during heat treatment.

@en

Advanced high strength steels (AHSS) are increasingly used in automotive industry; thousands of resistance spot welds are applied to car body-in-white. High alloying levels of AHSS result in lower weldability. Residual stresses play an essential role on the formation of defects and the mechanical performance of the weld. An electrical-thermal-metallurgical-mechanical finite element model was constructed to simulate the temperature and stress distribution during single and double pulse resistance spot welding. The models are validated by ex-situ synchrotron X-ray diffraction stress measurements. In this paper, single pulse and double pulse resistance spot welds were made on 1.3 mm thin sheets of a 3rd generation AHSS. Depth resolved stress measurements in two orthogonal directions were carried out using high-resolution powder diffraction at beamline ID22 of the European Synchrotron Research Facility. A monochromic 70 keV X-ray was used to record the d-spacing of (200) bcc planes in transmission mode. The strains were calculated from the shift in the d-spacing of the planes. The stresses were calculated by the biaxial Hook’s law. The numerical and experimental results show that the residual stresses in the weld nugget zone and the heat affected zone of the welds are tensile in nature, whereas the base material experiences compressive stresses. Lower residual stresses at the weld nugget and HAZ were obtained by applying a second current pulse. The simulated results show a good agreement with the residual stresses measured. This study provides a better understanding of the stress distribution in resistance spot welds and allows prediction of stresses as a result of welding conditions applied. @en

The effects of single and double pulse resistance spot welding on the microstructures of an advanced high strength automotive steel are presented in this work. The double pulse welding schemes partially remelt the primary weld nugget and anneal the area at the fusion boundary of the nugget. The effects of the annealing treatment on the segregation and the microstructure have been studied by electron probe microanalysis (EPMA) in combination with electron backscatter diffraction (EBSD). Results show that phosphorus has been redistributed at the primary weld nugget edge of the double pulse welds, while the mean block width and ellipticity of the prior austenite grains were smaller in welds subjected to double pulsing compared with single pulse weld. A favourable failure mode was obtained for the double pulse welds although behaviour did not correlate with the measured grain size.

@en

This paper presents the effects of double pulse resistance spot welding (RSW) on the microstructural evolution, elemental distribution and mechanical properties of a 3rd generation 1 GPa advanced high strength steel (AHSS). In order to investigate the effect of double pulsing, the steel was exposed to single and various double pulse RSW schedules. The first current pulse was applied to create the weld nugget, while the second current pulse generated a secondary weld nugget and annealed or (partial) re-melted the primary weld nugget, depending on the magnitude of the current. The effect of the second current pulse on the weld nugget and heat-affected zone characteristics was investigated using optical microscopy and electron probe microanalysis (EPMA). Optical and electron microscopy revealed that the secondary weld nugget is fully martensitic, showing a typical solidification microstructure, while the annealed zone reveals an equi-axed martensitic structure. EPMA results showed that elemental segregation has been considerably reduced in the annealed zone. Mechanical properties of the welds show that the AHSS studied is prone to weld metal failure for single pulse RSW. However, the double pulse RSW method can lead to significantly improved mechanical performance and favourable failure modes.@en