NASA's Planetary Science Decadal Survey has concluded that isotopic measurements of cometary water vapor are a means to unraveling the mysteries involving the origin of Earth's water and the evolution of our solar system. To support this, a recent Jet Propulsion Laboratory internal research program has developed quantum limited superconductor-insulator-superconductor (SIS) receivers in the important 500-600 GHz submillimeter frequency band. These instruments can be used to detect the deuterated water (HDO) ground state (110-101), H216O ortho ground state (110-101), and the oxygen isotopologues H217O and H218O with exquisite sensitivity. To achieve the presented results, we have investigated aluminum oxide (AlOx) and aluminum nitride (AlNx) barrier SIS tunnel junction mixers on the 6-μm silicon-on-insulator substrate. The AlOx and AlNx junction mixer blocks utilize diagonal and smooth-profile conical horns, respectively. In both cases, a commercial 4-8-GHz intermediate frequency low-noise amplifier (LNA) has been integrated into the mixer block. The AlOx (low-current-density) barrier SIS junctions were fabricated with 2-μm gold beam-lead technology, whereas in the case of the AlNx SIS tunnel junction, we use capacitive RF decoupling tabs. The latter approach simplifies fabrication, increases yield, eases the mounting process, and facilitates scaling to higher frequencies. For an actual flight mission, with operation ≤4.2 K, the allowed heat dissipation of the mixer-integrated LNA needs to be minimized. In this article, we also investigate the receiver sensitivity as a function of the LNA dc power consumption. We find that the dc power consumption of the LNA can be reduced to ∼1.6 mW with minimal loss in sensitivity. It is anticipated that the continued InP HEMT development for quantum computer applications are likely to reduce the required LNA power dissipation even further.

We compare the results of simulated and measured power efficiency and far-field beam pattern, for two reflective Fourier phase gratings, designed to generate 2 x 2 and 2 x 4 beams respectively from a single-beam, coherent source at 1.4 THz. The designed surface structures were manufactured on aluminum plates by a computer numerical control (CNC) micro-milling machine. Despite small differences between the designed and fabricated gratings, we measured power efficiencies of both gratings to be around 70%, which is in a good agreement with the simulated values. We also find a good agreement between the simulated and measured diffracted beam size and spatial distribution. We demonstrate the application of both gratings as multiple beam local oscillators to simultaneously pump (or operate) a 4-pixel array of superconducting heterodyne mixers.

Modelling, manufacturing and characterization of two 4 and 8-pixel Fourier phase gratings operated at 1.4 THz are reported, mainly applicable as local oscillator multiplexers for heterodyne receivers. Comparing the measurements with full 3D simulations shows good agreements and provides good understanding. Power efficiency of around 70% is experimentally derived for both gratings. We demonstrate the application of both, as multiple beam local oscillators to simultaneously pump (or operate) an array of 4-pixel superconducting mixers.

We report an extensive study of the effect of an additional dielectric layer on the frequency of terahertz quantum cascade lasers (QCLs). QCLs with third-order distributed feedback structure at frequencies of 3.5 and 4.7 THz are used in our experiment. The dielectric layer applied is either Silicon-dioxide (SiO₂) or Polymethylmethacrylaat (PMMA). We find that both dielectric layers can down shift the lasing frequency up to 6GHz on a 3.5THz QCL, and 13GHz for a 4.7THz QCL. Full 3D FEM simulations suggest that the effect is dominated by the effective thickness of the dielectric on the vertical walls of the laser structure, and also confirm that for a given dielectric layer the effect is stronger in the 4.7THz QCL due to its larger out-distribution of electric-magnetic field. The knowledge provides guideline to shift the frequency of an existing QCL used as a local oscillator in practical applications.

We report on a 4.7 THz heterodyne receiver designed for high resolution spectroscopy of the astronomically important neutral oxygen (OI) line at 4.745 THz. The receiver is based around a hot electron bolometer (HEB) mixer and quantum cascade laser (QCL) local oscillator. This receiver has been developed to fly on the Stratospheric Terahertz Observatory (STO-2), a balloon-borne 0.8 m telescope observing from an altitude of 44 km for 14 days or more. We measure a double sideband receiver noise temperature of 815 K (~ 7 times quantum noise) with a noise temperature IF bandwidth of 3.5 GHz. We describe the receiver performance expected in flight and outline novel approaches to QCL amplitude and frequency stabilization.

This paper is a report on the demonstration and stabilization of a 2x4 NbN hot electron bolometer (HEB) array receiver for GUSTO based on a multiple beam local oscillator (LO). Through the combination of a FIR Gas laser and a Fourier phase grating we were able to generate a 8 beam pattern at 1.4 THz. For the array demonstration, it used a 2x2 HEB mixer array which was translated vertically to match the full 2x4 LO beam pattern. Here two lens with a 60 mm were applied to reduce the beam pattern divergence, allowing for a 12 mm spacing between the beams to be achieved at 130 mm from the grating. To stabilize the array receiver, we introduced a new stabilization method, requiring only a voice coil PID controlled loop between the beam originated from the gas laser and a given pumped pixel. The total power Allan time measurements indicate a five times improvement on a two-pixel system stability.

We report an extensive study of the effect of an additional dielectric layer on the frequency of terahertz quantum cascade lasers (QCLs). QCLs with third-order distributed feedback structure at frequencies of 3.5 and 4.7 THz are used in our experiment. The applied dielectric layer is either Silicon dioxide (SiO₂) or Polymethylmethacrylaat (PMMA). We find that both dielectric layers can shift the lasing frequency by up to-6 GHz on a 3.5-THz QCL, and up to-13 GHz for a 4.7-THz QCL. Full 3-D FEM simulations suggest that the effect is dominated by the effective thickness of the dielectric on the side walls of the laser structure, and also confirm that for a given dielectric layer, the effect is stronger in the 4.7-THz QCL due to its different extension of the electromagnetic field to the free space. This study provides a guideline for shifting the frequency of an existing QCL for frequency critical applications such as spectroscopy or use as a local oscillator.

The terahertz region is of great importance for spectroscopy since many molecules have absorption fingerprints there. Frequency combs based on terahertz quantum cascade lasers feature broadband coverage and high output powers in a compact package, making them an attractive option for broadband spectroscopy. Here, we demonstrate the first multiheterodyne spectroscopy using two terahertz quantum cascade laser combs. Over a spectral range of 250 GHz, we achieve average signal-to-noise ratios of 34 dB using cryogenic detectors and 24 dB using room-temperature detectors, all in just 100 µs. As a proof of principle, we use these combs to measure the broadband transmission spectrum of etalon samples and show that, with proper signal processing, it is possible to extend the multiheterodyne spectroscopy to quantum cascade laser combs operating in pulsed mode. This greatly expands the range of quantum cascade lasers that could be suitable for these techniques and allows for the creation of completely solid-state terahertz laser spectrometers.