Steel production accounts for approximately 8% of all global CO2 emissions, with the primary steelmaking route using iron ores accounting for about 80% of those emissions, mainly due to the use of fossil-based reductants and fuel. Hydrogen-based reduction of iron oxide is an alternative for primary synthesis. However, to counteract global warming, decarbonization of the steel sector must proceed much faster than the ongoing transition kinetics in primary steelmaking. Insufficient supply of green hydrogen is a particular bottleneck. Realizing a higher fraction of secondary steelmaking thus is gaining momentum as a sustainable alternative to primary production. Steel production from scrap is well established for long products (rails, bars, wire), but there are two main challenges. First, there is not sufficient scrap available to satisfy market needs. Today, only one-third of global steel demand can be met by secondary metallurgy using scrap since many steel products have a lifetime of several decades. However, scrap availability will increase to about two-thirds of total demand by 2050 such that this sector will grow massively in the next decades. Second, scrap is often too contaminated to produce high-performance sheet steels. This is a serious obstacle because advanced products demand explicit low-tolerance specifications for safety-critical and high-strength steels, such as for electric vehicles, energy conversion and grids, high-speed trains, sustainable buildings, and infrastructure. Therefore, we review the metallurgical and microstructural challenges and opportunities for producing high-performance sheet steels via secondary synthesis. Focus is placed on the thermodynamic, kinetic, chemical, and microstructural fundamentals as well as the effects of scrap-related impurities on steel properties.@en

Iron powder can be a sustainable alternative to fossil fuels in power supply due to its high energy density and abundance. Iron powder releases energy through exothermic oxidation (combustion), and stores back energy through its subsequent hydrogen-based reduction, establishing a circular loop for renewable energy supply. Hydrogen-based direct reduction is also gaining global momentum as possible future backbone technology for sustainable iron and steel production, with the aim to replace blast furnaces. Here, we investigate the microstructural formation mechanisms and reduction kinetics behind hydrogen-based direct reduction of combusted iron powder at moderate temperatures (400–500 °C) using thermogravimetry, ex-situ X-ray diffraction, scanning electron microscopy coupled with energy dispersive spectroscopy and electron backscatter diffraction, as well as in-situ high-energy X-ray diffraction. The influence of pre-oxidation treatment was studied by reducing both as-combusted iron powder (50 % magnetite and 50 % hematite) and the same powder after pre-oxidation (100 % hematite). A gas diffusion-limited reaction was obtained during the in-situ high-energy X-ray diffraction experiment, with successive hematite and magnetite reduction, and a strong increase in reduction kinetics with initial hematite content. Faster reduction kinetics were obtained during the thermogravimetry experiment, with simultaneous hematite and magnetite reduction. In this case, the reduction reaction was limited by a mix of phase boundary and nucleation and growth models, as analyzed by multi-step model fitting methods as well as by microstructural investigation. When not limited by gas diffusion, the pre-oxidation treatment showed almost no influence on the reduction time but a strong effect on the final microstructure of the reduced powder.

@en

Grain boundaries in noble metal catalysts have been identified as critical sites for enhancing catalytic activity in electrochemical reactions such as the oxygen reduction reaction. However, conventional methods to modify grain boundary density often alter particle size, shape, and morphology, obscuring the specific role of grain boundaries in catalytic performance. This study addresses these challenges by employing gold nanoparticle assemblies to control grain boundary density through the manipulation of nanoparticle collision frequency during synthesis. We demonstrate a direct correlation between increased grain boundary density and enhanced two-electron oxygen reduction reaction activity, achieving a significant improvement in both specific and mass activity. Additionally, the gold nanoparticle assemblies with high grain boundary density exhibit remarkable electrochemical stability, attributed to boron segregation at the grain boundaries, which prevents structural degradation. This work provides a promising strategy for optimizing the activity, selectivity, and stability of noble metal catalysts through precise grain boundary engineering.

@en

Excellent properties (durability, wear and corrosion resistance) and long service life under extreme conditions are essential for the successful application of metallic materials in the energy sector. In particular, for future fusion applications, high Cr ferrous alloys (in our case Eurofer) are of great interest. Importantly, modified microstructure with higher dimensional stability improves corrosion and wear resistance properties. In this study, we successfully manipulate the desired type of microstructure, which could provide a solution to current challenges in such a high temperature, highly corrosive and highly irradiated environment, using a novel technique of cryogenic processing (CP). The research identifies the CP-driven changes not only to the microstructure, but also to the local chemistry and bonding state of the key alloying elements. The correlations and individual phenomena associated with CP have been evaluated using state-of-the-art techniques such as atom probe tomography and synchrotron-based in-situ scanning photoemission spectroscopy. This novel process and its novel microstructural manipulation opens up new possibilities for materials processing for future energy applications.

@en

Ammonia is a promising alternative hydrogen carrier that can be utilized for the solid-state reduction of iron oxides for sustainable ironmaking due to its easy transportation and high energy density. The main challenge for its utilization on an industrial scale is to understand the reaction kinetics under different process conditions and the associated nitrogen incorporation in the reduced material that originates from ammonia decomposition. In this work, the effect of temperature on the reduction efficiency and nitride formation is investigated through phase, local chemistry, and gas evolution analysis. The effects of inherent reactions and diffusion on phase formation and chemistry evolution are discussed in relation to the reduction temperature. The work also discusses nitrogen incorporation into the material through both spontaneous and in-process nitriding, which fundamentally affects the structure and chemistry of the reduced material. Finally, the effect of nitrogen incorporation on the reoxidation tendency of the ammonia-based reduced material is investigated and compared with that of the hydrogen-based reduced counterpart. The results provide a fundamental understanding of the reduction and nitriding for iron oxides exposed to ammonia at temperatures from 500 to 800 °C, serving as a basis for exploitation and upscaling of ammonia-based direct reduction for future green steel production.

@en

Metallurgical production traditionally involves three steps: extracting metals from ores, mixing them into alloys by liquid processing and thermomechanical processing to achieve the desired microstructures ^1,2. This sequential approach, practised since the Bronze Age, reaches its limit today because of the urgent demand for a sustainable economy ^2–5: almost 10% of all greenhouse gas emissions are because of the use of fossil reductants and high-temperature metallurgical processing. Here we present a H ₂-based redox synthesis and compaction approach that reforms traditional alloy-making by merging metal extraction, alloying and thermomechanical processing into one single solid-state operation. We propose a thermodynamically informed guideline and a general kinetic conception to dissolve the classical boundaries between extractive and physical metallurgy, unlocking tremendous sustainable bulk alloy design opportunities. We exemplify this approach for the case of Fe–Ni invar bulk alloys ^6,7, one of the most appealing ferrous materials but the dirtiest to produce: invar shows uniquely low thermal expansion ^6,8,9, enabling key applications spanning from precision instruments to cryogenic components ^10–13. Yet, it is notoriously eco-unfriendly, with Ni causing more than 10 times higher CO ₂ emission than Fe per kilogram production ^2,14, qualifying this alloy class as a perfect demonstrator case. Our sustainable method turns oxides directly into green alloys in bulk forms, with application-worthy properties, all obtained at temperatures far below the bulk melting point, while maintaining a zero CO ₂ footprint.

@en

Hydrogen-based direct reduction (HyDR) of iron ores has attracted immense attention and is considered a forerunner technology for sustainable ironmaking. It has a high potential to mitigate CO ₂ emissions in the steel industry, which accounts today for ~ 8–10% of all global CO ₂ emissions. Direct reduction produces highly porous sponge iron via natural-gas-based or gasified-coal-based reducing agents that contain hydrogen and organic molecules. Commercial technologies usually operate at elevated pressure, e.g., the MIDREX process at 2 bar and the HyL/Energiron process at 6–8 bar. However, the impact of H ₂ pressure on reduction kinetics and microstructure evolution of hematite pellets during hydrogen-based direct reduction has not been well understood. Here, we present a study about the influence of H ₂ pressure on the reduction kinetics of hematite pellets with pure H ₂ at 700 °C at various pressures, i.e., 1, 10, and 100 bar under static gas exposure, and 1.3 and 50 bar under dynamic gas exposure. The microstructure of the reduced pellets was characterized by combining X-ray diffraction and scanning electron microscopy equipped with electron backscatter diffraction. The results provide new insights into the critical role of H ₂ pressure in the hydrogen-based direct reduction process and establish a direction for future furnace design and process optimization. Graphical Abstract: (Figure presented.)

@en

The ultrafine cellular structure promotes the extraordinary mechanical performance of metals manufactured by laser powder‐bed‐fusion (L‐PBF). An in‐depth understanding of the mechanisms governing the thermal stability of such structures is crucial for designing reliable L‐PBF components for high‐temperature applications. Here, characterizations and 3D discrete dislocation dynamics simulations are performed to comprehensively understand the evolution of cellular structures in 316L stainless steel during annealing. The dominance of screw‐type dislocation dipoles in the dislocation cells is reported. However, the majority of dislocations in sub‐grain boundaries (SGBs) are geometrically necessary dislocations (GNDs) with varying types. The disparity in dislocation types can be attributed to the variation in local stacking fault energy (SFE) arising from chemical heterogeneity. The presence of screw‐type dislocations facilitates the unpinning of dislocations from dislocation cells/SGBs, resulting in a high dislocation mobility. In contrast, the migration of SGBs with dominating edge‐type GNDs requires collaborative motion of dislocations, leading to a sluggish migration rate and an enhanced thermal stability. This work emphasizes the significant role of dislocation type in the thermal stability of cellular structures. Furthermore, it sheds light on how to locally tune dislocation structures with desired dislocation types by adjusting local chemistry‐dependent SFE and heat treatment.@en

When solid-state redox-driven phase transformations are associated with mass loss, vacancies are produced that develop into pores. These pores can influence the kinetics of certain redox and phase transformation steps. We investigated the structural and chemical mechanisms in and at pores in a combined experimental-theoretical study, using the reduction of iron oxide by hydrogen as a model system. The redox product (water) accumulates inside the pores and shifts the local equilibrium at the already reduced material back toward reoxidation into cubic Fe1-xO (where x refers to Fe deficiency, space group Fm3¯m). This effect helps us to understand the sluggish reduction of cubic Fe1-xO by hydrogen, a key process for future sustainable steelmaking.

@en

The effect of hydrogen on the surface morphology and nanomechanical properties of Ni-based Alloy 725 under solution-annealed (SA) and precipitation-hardened (API) conditions was thoroughly studied. The investigation involved in situ nanoindentation testing, microscopy characterization, statistical analysis, and numerical simulation approaches. The results showed the distinctive effects of hydrogen on the pop-in and hardness in the SA and API samples. For the SA sample, hydrogen mainly dissolved as solid solute in the matrix, causing enhanced lattice friction on the dislocation motion and increasing the internal stress via lattice expansion. Thus, an enhanced hardness, a reduced pop-in width/load ratio, and numerous surface steps were detected in the presence of hydrogen. For the API sample, the strengthening γ′′ phases were the stress concentrators, and the dislocations nucleated heterogeneously, demonstrating indistinctive pop-in phenomena. Furthermore, the precipitates in the API sample affected the trapping behavior of hydrogen, thereby resulting in the hardness change, which reflected the competition between solution hardening in the matrix and vacancy softening mechanism in precipitates.

@en

Hydrogen-based reduction of iron ores is the key technology for future sustainable ironmaking, to mitigate the CO2 burden from the steel industry, accounting for ~7–8% of all global emissions. However, using hydrogen as a reductant prompts concerns about hydrogen embrittlement in steel products. This raises the question of how much hydrogen remains from green ironmaking in the metal produced. We answer this question here by quantifying the amount of hydrogen in iron produced via two hydrogen-based ironmaking processes, namely, direct reduction and plasma smelting reduction. Results suggest no threat of hydrogen embrittlement resulting from using hydrogen in green steel production.@en

The hydrogen-based direct reduction of iron ores is a disruptive routine used to mitigate the large amount of CO ₂ emissions produced by the steel industry. The reduction of iron oxides by H ₂ involves a variety of physicochemical phenomena from macroscopic to atomistic scales. Particularly at the atomistic scale, the underlying mechanisms of the interaction of hydrogen and iron oxides is not yet fully understood. In this study, density functional theory (DFT) was employed to investigate the adsorption behavior of hydrogen atoms and H ₂ on different crystal FeO surfaces to gain a fundamental understanding of the associated interfacial adsorption mechanisms. It was found that H ₂ molecules tend to be physically adsorbed on the top site of Fe atoms, while Fe atoms on the FeO surface act as active sites to catalyze H ₂ dissociation. The dissociated H atoms were found to prefer to be chemically bonded with surface O atoms. These results provide a new insight into the catalytic effect of the studied FeO surfaces, by showing that both Fe (catalytic site) and O (binding site) atoms contribute to the interaction between H ₂ and FeO surfaces.

@en

The reduction of magnetite-based iron ore fines in a hydrogen-induced fluidized bed becomes an attractive fossil-free ironmaking route. Our previous study showed that a prior oxidation treatment of magnetite was helpful to improve its fluidization and reduction behavior. However, the underlying oxidation mechanisms of magnetite ore fines remained unclear and required further investigations. In this study, two magnetite ore brands were analyzed viain situ high-temperature X-ray diffraction (HT-XRD) during oxidation, to investigate the thermal transformation of Fe ₃O ₄ to α-Fe ₂O ₃ at crystal scale. The lattice constants and crystallite sizes of both phases and oxidation degree were evaluated at different temperatures based on the HT-XRD patterns. The lattice constants of Fe ₃O ₄ and α-Fe ₂O ₃ increased with an increase in temperature due to the thermal expansion and can be successfully fitted with temperature by second-order polynomials. With Fe ₃O ₄ being oxidized into Fe ₂O ₃, the Fe ₂O ₃ crystallite grew and showed a certain growth habit. The Fe ₂O ₃ crystallite grew faster along the a/b axis than the c axis. The oxidation kinetics followed the parabolic law as shown by the sigmoid-shaped oxidation degree curve, suggesting that the solid diffusion of ions was the rate-limiting step.

@en

Tungsten stands a prime candidate for plasma-facing applications in fusion reactors, attributed to its capacity to withstand high temperatures and intensive particle fluxes. The operational heat flux, however, can induce recrystallisation of the initial microstructure, increasing the brittle-to-ductile transition temperature. Although such a phenomenon is thought to result from impurity segregation to grain boundaries, direct evidence of impurity-induced grain boundary embrittlement has not yet been reported. Addressing this, our study employs microcantilever testing, coupled with local chemical analysis via atom probe tomography, to unveil the impact of impurity segregation on the fracture toughness of recrystallised tungsten with a purity of 99.98 at.%. The in situ fracture toughness measurements were performed with the notch placed directly at random high-angle grain boundaries, revealing brittle failure regardless of grain boundary misorientation or grain orientation. Notably, both single-crystalline microcantilevers and the as-received material exhibited significant plasticity before failure, with instances without crack propagation. In contrast, recrystallised grain boundaries displayed a fracture toughness of 4.7 ± 0.4 MPa·√m, determined using a linear elastic approach - notably lower than for cleavage plane fracture in tungsten microcantilevers. Local atom probe analysis of the high-angle grain boundaries exposed phosphorous segregation exceeding 2 at.% at the recrystallised interfaces, stemming from recrystallisation. Atomistic simulations confirmed the role of phosphorous in embrittling high-angle grain boundaries in tungsten, while additionally revealing mechanisms of crack-grain boundary interactions and their dependence on phosphorous segregation.

@en

Out of the multitude of researched processing routes for sustainable ironmaking, hydrogen-based direct reduction and hydrogen plasma smelting reduction (HyPSR) are currently the most promising candidates for a successful industrial application. Both processes operate under gaseous atmospheres, which turn the partial and absolute pressure of hydrogen into a relevant process parameter. Here, we present first insights into the influence of total pressure and concentration of hydrogen on the reduction of hematite, focusing on the more pressure-sensitive route (HyPSR). The effect of pressure on the dissociation of H2 molecules into metastable H atoms or H+ ions,- and the overall hydrogen utilization is discussed using a thermodynamic approach. Validation experiments were conducted to testify the practical feasibility of adjusting these parameters. A decrease in the total pressure of the system from 900 mbar to 450 mbar resulted in an improved hydrogen utilization, thus suggesting that a larger population of H atoms can exist in the plasma arcs ignited under 450 mbar. An increase in the hydrogen concentration to 20 vol.% lead to undesired evaporation, likely because of a parallel increase in plasma temperature. Possibilities and challenges for exploiting these pressure-related phenomena for the industrial production of green steel are outlined and discussed.@en

Iron making is the biggest single cause of global warming. The reduction of iron ores with carbon generates about 7% of the global carbon dioxide emissions to produce ≈1.85 billion tons of steel per year. This dramatic scenario fuels efforts to re-invent this sector by using renewable and carbon-free reductants and electricity. Here, the authors show how to make sustainable steel by reducing solid iron oxides with hydrogen released from ammonia. Ammonia is an annually 180 million ton traded chemical energy carrier, with established transcontinental logistics and low liquefaction costs. It can be synthesized with green hydrogen and release hydrogen again through the reduction reaction. This advantage connects it with green iron making, for replacing fossil reductants. the authors show that ammonia-based reduction of iron oxide proceeds through an autocatalytic reaction, is kinetically as effective as hydrogen-based direct reduction, yields the same metallization, and can be industrially realized with existing technologies. The produced iron/iron nitride mixture can be subsequently melted in an electric arc furnace (or co-charged into a converter) to adjust the chemical composition to the target steel grades. A novel approach is thus presented to deploying intermittent renewable energy, mediated by green ammonia, for a disruptive technology transition toward sustainable iron making.

@en

The effect of the scarcely reported F phase on hydrogen-assisted cracking in nickel-based Alloy 725 was thoroughly studied by combining tensile tests, advanced characterization, and density functional theory (DFT) calculations. The results show grain boundary precipitate F phase promotes intergranular fracture in a hydrogen environment. DFT calculations further indicates hydrogen atoms lower the binding strength of the F phase and Ni matrix interfaces. More importantly, our study showed for the first time that the addition of approximately 0.01 wt.% boron can effectively suppress F phase precipitation, thereby elevating the hydrogen resistance of Alloy 725.

@en

Steels with medium manganese (Mn) content (3∼12 wt-%) have emerged as a new alloy class and received considerable attention during the last decade. The microstructure and mechanical response of such alloys show significant differences from those of established steel grades, especially pertaining to the microstructural variety that can be tuned and the associated micromechanisms activated during deformation. The interplay and tuning opportunities between composition and the many microstructural features allow to trigger almost all known strengthening and strain-hardening mechanisms, enabling excellent strength-ductility synergy, at relatively lean alloy content. Previous investigations have revealed a high degree of microstructure and deformation complexity in such steels, but the underlying mechanisms are not adequately discussed and acknowledged. This encourages us to critically review and discuss these materials, focusing on the progress in fundamental research, with the aim to obtain better understanding and enable further progress in this field. The review addresses the main phase transformation phenomena in these steels and their mechanical behaviour, covering the whole inelastic deformation regime including yielding, strain hardening, plastic instability and damage. Based on these insights, the relationships between processing, microstructure and mechanical properties are critically assessed and rationalized. Open questions and challenges with respect to both, fundamental studies and industrial production are also identified and discussed to guide future research efforts.

@en

With the aim to find the best simulation routine to accurately predict the ground−state structures and properties of iron oxides (hematite, magnetite, and wustite) using density functional theory (DFT) with Hubbard-U correction, a significant amount of DFT calculations were conducted to investigate the influence of various simulation parameters (energy cutoff, K-point, U value, magnetization setting, smearing value, etc.) and pseudopotentials on the structures and properties of iron oxides. With optimized simulation parameters, the obtained equation of state, lattice constant, bulk moduli, and band gap is much closer to the experimental values compared with previous studies. Due to the strong coupling between the 2p orbital of O and the 3d orbital of Fe, it was found that Hubbard-U correction obviously improved the results for all three kinds of iron oxides including magnetite which has not yet been tested with U correction before, but the U value should be different for different oxides (3 ev, 4 ev, 4 ev for hematite, magnetite, and wustite, respectively). Two kinds of spin magnetism settings for FeO are considered, which should be chosen according to different calculation purposes. The detailed relationship between the parameter settings and the atomic structures and properties were analyzed, and the general principles for future DFT calculation of iron oxides were provided.

@en

Iron- and steelmaking cause ∼7% of the global CO ₂ emissions, due to the use of carbon for the reduction of iron ores. Replacing carbon by hydrogen as the reductant offers a pathway to massively reduce these emissions. However, the production of hydrogen using renewable energy will remain as one of the bottlenecks at least during the next two decades, because making the gigantic annual crude steel production of 1.8 billion tons sustainable requires a minimum stoichiometric amount of ∼97 million tons of green hydrogen per year. Another fundamental aspect to render the ironmaking sector more sustainable lies in an optimal utilization of green hydrogen and energy, thus reducing efforts for costly in-process hydrogen recycling. We therefore demonstrate here how the efficiency in hydrogen and energy consumption during iron ore reduction can be dramatically improved by the knowledge-based combination of two technologies: partially reducing the ore at low temperature via solid-state direct reduction (DR) to a kinetically defined degree, and subsequently melting and completely transforming it to iron under a reducing plasma (i.e. via hydrogen plasma reduction, HPR). Results suggest that an optimal transition point between these two technologies occurs where their efficiency in hydrogen utilization is equal. We found that the reduction of hematite through magnetite into wüstite via DR is clean and efficient, but it gets sluggish and inefficient when iron forms at the outermost layers of the iron ore pellets. Conversely, HPR starts violent and unstable with arc delocalization, but proceeds smoothly and efficiently when processing semi-reduced oxides, an effect which might be related to the material's high electrical conductivity. We performed hybrid reduction experiments by partially reducing hematite pellets via DR at 700 °C to 38% global reduction (using a standard thermogravimetry system) and subsequently transferring them to HPR, conducted with a lean gas mixture of Ar-10%H ₂ in an arc-melting furnace, to achieve full conversion into liquid iron. This hybrid approach allows to exploit the specific characteristics and kinetically favourable regimes of both technologies, while simultaneously showing the potential to keep the consumption of energy and hydrogen low and improve both, process stability and furnace longevity by limiting its overexposure to plasma radiation.

@en