The level of detail on modern geological models requires higher resolution grids that may render the simulation of multiphase flow in porous media intractable. Moreover, these models may comprise highly heterogeneous media with phenomena taking place in different scales. Scale transferring techniques allow for the solution of such problems in a lower resolution scale at reduced computational cost. Among these techniques, the Multiscale Finite Volume (MsFV) method constructs a set of numerical operators in order to map quantities from the fine-scale mesh to a coarser one and vice-versa while maintaining flux conservation on both scales. However, the MsFV formulation, as originally stated, is only consistent on k-orthogonal grids since it uses a linear Two-point Flux Approximation (TPFA) method and may struggle to generate consistent primal-dual coarse grids pairs on unstructured grids. The Multiscale Restriction Smoothed-Basis method (MsRSB) improves on the MsFV by introducing a new iterative procedure to find the multiscale operators and the concept of support regions which reduces the method's complexity when applied to unstructured fine and coarse grids. The original version was only consistent on k-orthogonal fine grids due to the TPFA discretization, but filtering methods have been developed to also enable consistent multipoint schemes on the fine scale. Meanwhile, the Multiscale Control Volume method (MsCV) replaces the TPFA by the Multipoint Flux Approximation with a Diamond stencil (MPFA-D) scheme on the fine-scale while further enhancing the generation of the geometric entities to allow unstructured grids on the fine and coarse scales for two-dimensional simulations. In this work we propose an extension to three-dimensional geometries of both the MsCV and the algorithm to obtain the multiscale geometric entities based on the concept of a background grid, a coarser grid used as a proxy for the primal coarse grid. We modify the original MPFA-D method to use the very robust Global Least Squares (GLS) interpolation technique to obtain the required auxiliary nodal unknowns. We also introduce an enhanced version of the 3-D MsCV with the incorporation of the enhanced MsRSB (E-MsRSB) to enforce M-matrix properties and improve convergence. Finally, we employ the MsCV operators in a two-stage smoother to show how it can be used as a good iterative procedure to recover the fine-scale solution. We show that the 3-D MsCV method produces good results employing unstructured grids on both scales to handle the simulation of the single-phase flow in anisotropic, and heterogeneous porous media and that the smoothing procedure is able to accurately retrieve the fine-scale solution within a few iterations.

@en

The modeling of fluid flow in heterogeneous, anisotropic and fractured porous media is relevant in many applications, including hydrocarbon and groundwater extraction, dispersion of contaminants, hydrogen or carbon dioxide (CO₂) storage. Thus, accurate and scalable simulation of fluid flow through these formations continues to be a great challenge. The presence of fractures that are explicitly modeled, ranging from flow barriers to highly conductive channels, significantly increases the complexity of the numerical simulation. The Embedded Discrete Fracture Model (EDFM) produces results that can be as accurate as those obtained using equidimensional Discrete Fracture Models (DFM) at a much lower computational cost for highly conductive fractures, but it is not adequate for impermeable barriers. In contrast, the pEDFM (projection-based Embedded Discrete Fracture Model) produces accurate results for both, channels and barriers by using additional matrix-fracture connectivities. In its current versions, it is restricted to cartesian and corner-point grid geometries and to the classical Two Point Flux Approximation (TPFA) scheme. In this work, for the first time, the pEDFM is extended to handle unstructured tetrahedral meshes (pEDFM-U). In addition, interface fluxes are approximated by using the Multipoint Flux Approximation method with a Diamond stencil (MPFA-D). This allows for simulation of highly heterogeneous and anisotropic geo-models. The developed method is robust and can deal with full permeability tensors on arbitrary tetrahedral meshes. The advective terms are discretized considering an implicit First Order Upwind (FOU) method. Our method is implemented within the DARSim (Delft Advanced Reservoir Simulation) open-source simulator framework. Through several test cases, the proposed method showed to be robust and capable to accurately capture the effects of both high and low permeability fractures for general tetrahedral meshes, under arbitrary heterogeneous and anisotropic permeability tensors for the rock matrix.

@en

A novel Flux Limited Splitting (FLS) non-linear Finite Volume (FV) method for families of linear Control Volume Distributed Multi Point Flux Approximation (CVD-MPFA) schemes is presented. The new formulation imposes a local discrete maximum principal (LDMP) which ensures that the discrete solution is free of spurious oscillations. The FLS scheme can be seen as a natural extension of the M-Matrix Flux Splitting method that splits the MPFA flux components in terms of the Two-Point Flux Approximation (TPFA) flux and Cross Diffusion Terms (CDT), with the addition of a dynamically computed relaxation parameter to the CDT that identifies and locally corrects the regions where the LDMP is violated. Moreover, the whole non-linear procedure was devised as a series of simple straightforward matrix operations. The methodology is presented considering the Multi-Point Flux Approximation with a Diamond (MPFA-D) in what we call the FLS + MPFA-D formulation which is tested using a series of challenging benchmark problems. For all test cases, the FLS repair technique imposes the LDMP and eliminates the spurious oscillations induced by the original MPFA-D method.@en